Search Documents

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By D. S. Kingery, D. W. Mitchell

The authors attended the 11th International Conference of Directors of Safety in Mines Research held in France, July 1963. In addition to Conference discussions pertaining to control of coal dust they had the added assignment to study present European practices for neutralizing the coal-dust explosion hazard. Information was obtained through discussions with the Research Directors, by visits to testing stations and observations of operating mines in various countries. This paper tells what the current practice in this field is in Europe, and how effectively coal dust explosions are controlled. The method is rock dust barriers. CONTROL OF COAL DUST DISSEMINATION Experience in Europe indicates that the control of dust production and dissemination by water or foam systems is not successful except during undercutting. Cybulski, Dawes, and DeBraaf - respectively Director, Mines Research Establishment "Barbara", Katowice, Poland; Principal Scientific Officer, Safety in Mines Research Establishment, Sheffield, England; and Chief, Central Mines Research Establishment, Hoensbroek, Treebeek, The Netherlands - believe that wetted dust becomes readily dispersible and abatement measures should be considered only as a temporary means for reducing the health hazard. In an effort to reduce the health hazard, calcium chloride is used on the floor of main haulageways in Dutch mines and water infusion is practiced in Germany in mines where the coal is relatively porous. With respect to wet coal dust, the Belgians, British, Dutch, French, and Russians reportedly have accepted the results of research from the Polish and American experimental mines on the effectiveness of water as an inert in arresting explosion propagation. The Polish use the two test methods proposed by the U.S. Bureau of Mines1 for evaluation of the adequacy of wetness of mine dust; they require that water be added to the wet dust to maintain a minimum of 50% moisture by weight if dependence is placed on water alone. GENERALIZED ROCK DUSTING The general attitude with regard to protection against coal dust explosions throughout Europe is that generalized rock dusting is a vital primary step to inhibit initial ignitions but definite emphasis is also placed upon the efficiency of rock dust barriers. Those exceptions to generalized rock dusting are Germany and Austria where some rock dusting is done but principal reliance is placed upon rock dust barriers. The rock dust used in Belgium, Holland, Russia, and Poland is coarser than that used in the U. S.; 50% of the dust is through a No. 200 sieve (75 microns). Recent research by the Polish indicates that the portion finer than 20 microns is ineffective in arresting explosion propagation, and that the rock

Jan 1, 1964

By Gordon C. Hicks

Prior to 1950 most fertilizer manufactured in the United States was produced in a nongranular form. In such form, the material caked when stored and was extremely dusty when applied in the field. About this time a wide interest developed in the fertilizer industry for the manufacture of a granular, high-analysis fertilizer of improved physical properties. Thus, TVA began work on fertilizer granulation about 1950 using both a pugmill (double-shaft paddle mixer) for a thick slurry of nitric phosphate and a continuous ammoniator-granulator drum for superphosphate-base mixed fertilizer. Granulation in these units was mainly by agglomeration. The liquid phase generated by the moisture and by the heat of reaction of ammonia with acidic materials, such as superphosphate and sulfuric or phosphoric acids, resulted in agglomeration of the solid ingredients. About 1956, TVA began studies of the use of a pan or disk granulator for production of ammonium nitrate or other fertilizers containing a large proportion of ammonium nitrate, such as 30-10-0 ammonium phosphate nitrate. This is the layering method of granulation. More recently, TVA has demonstrated pan granulation of urea from a highly concentrated solution and granulation of ammonium polyphosphate melts in a pugmill. The bulk of TVA studies throughout the years has related to use of the drum granulator. About 200 granulation plants in the United States have been licensed and built to use the TVA continuous ammoniator-granulator; it is estimated that more than half of the 20 million tons of mixed fertilizer used in the United States in 1974/1975 was produced in these plants. Some other granulation processes developed for use in the drum granulator include diammonium phosphate, monoammonium phosphate, urea- ammonium phosphate, ammoniated superphosphate, and most recently, NPK fertilizers by melt granulation using a pipe reactor.

Jan 1, 1977

By J. B. Rather

The use of sulfuric acid in refining illuminating oils antedates the beginning of the petroleum industry in America by many years. It was used as early as 1792 by Tower in refining "coal oil" in the British Isles, and by 1860 there were 53 refineries in the United States manufacturing "coal oil," most of them using sulfuric acid as a refining agent. Following the completion of the Drake well in 1859, many of the "coal oil" refiners began to use petroleum for manufacturing illuminating oil, and their methods and equipment were adapted so far as possible to this new raw material. The value of sulfuric acid in refining L'coal oil" having been established, this reagent was immediately tried and found to be satisfactory in refining petroleum. Notwithstanding the tremendous advances in petroleum technology since that time, sulfuric acid remains today the most valuable and most widely used means for refining petroleum products. Early Methods of Disposal of Acid Sludge With the almost immediate expansion of the petrolrum industry came the problem of disposing of the acid sludge produced in the refining operations. While in 1859, the year of the discovery of the Drake well, a patent was granted for sludge separation and separated acid concrntration, most of the earlier refiners, and rnany of their successors, felt that separation and recovery of spent acid was uneconomical. Accordingly, many of then) disposed of the sludge in any way that seemed expedient nt the time. It was huricd in the refinery grounds, harged and tlurnped at sea, run into neighboring streams, or dumped into sewers. Some optimists carted it to open pits in the hope that it would eithcr sink into the ground or evaporate. Not so many years ago, the superintendent of nn eastern refinery, who was using the open-pit method of disposal, lost, a sludge cart, with horse attached, in such a pit. The horse was recovred almost immediately, but its availability for further use was reduced to zero by the loss of its hair.

Jan 1, 1928

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of open-ings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35° to 40° to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transporta-tion of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars prac-tically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939

By C. F. Austin

lined-cavity shaped charge is an explosive mass with a cavity at one end and the detonator at the opposite end. The cavity is lined with a dense material, such as metal, glass, or a ceramic. Such an explosive device can be a useful drilling tool. Lined-cavity shaped charges are constructed to do just one thing — create a high-velocity jet of liner particles that can bore a hole in a target. The liner must be smooth and symmetrical, and high-velocity, high-brisance explosive must be used rather than ordinary commercial dynamites. Since the depth of target penetration is related to jet length, a standoff distance should be provided to hold the charge a short distance from the target. This allows the jet to lengthen prior to target impact. The best results are obtained when the jet is perpendicular to the target surface. Charges can be positioned for firing by taping them to a stake or simply laying them on a flat surface at the proper distance and angle with respect to the target. EFFECTS ON THE TARGET When a jet strikes a rock target, the jet and target particles at the jet-target interface move outward radially with respect to the jet axis to create a tremendous compressive load on the target material immediately below the target surface. The result is a shallow crater formed by spalling at the point of target entry. After cratering ceases, the steadily deepening hole continues to form as a result of the jet's imparting radial motion to the target particles at the jet-target interface. These radially moving particles collide with one another and with the hole walls, the net motion of the spent jet particles and target particles being back out of the hole in an axial direction (the backblast). The backblast keeps the penetration free of debris during penetration, al- though loose surface rock often falls into the hole after penetration ceases. The sudden stress relief after penetration ceases sometimes results in minor hole-wall rebound, which can partially fill the hole. The hole bottom will taper as the jet velocity decreases, until the jet velocity is too low to maintain the backblast. At this point the remaining jet and the following slug material are simply packed into the hole bottom. HAZARDS INHERENT IN USE Air blast from the highly brisant explosives used in shaped charges can damage nearby structures

Jan 1, 1961

By P. Nicholls

Patent records show that the attempt to improve the burning of fuel by mixture or pretreatment with chemicals dates back to the early years of the last century. By 1845 English and French patents had included the specific beneficiations of elimination or reduction of smoke, soot and clinker; reduction of the ashes; elimination of sulphur fumes; increase of the rate of burning; increase of the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 lb. or more per ton of fuel, but after 1860 the quantity was seldom more than 4 lb. There is no record of the extent to which these patents were commercialized, but after 1874 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many proprietary products were marketed under the general name of "fuel savers," the principal sales being in small packages for the use of householders; savings of from 10 to 40 per cent of the coal were promised. Starting with 1927, the use of proprietary or other mixtures of chemicals was extended to power plants and to treatment of coals at the mines, the claims of saving of fuel being subordinated to those of general improvement and, in particular, to reduction of clinker-ing. Such expectations are attractive and a number of companies experimented with or adopted the practice. There were reports of improved operation, but, apparently, few were confident enough that these improvements were due to the salts to publish the results of tests or their records of operation. There are no data on the yearly tonnage of coal treated but indirect reports suggest that it has been relatively large. Since its establishment in 1910, the U. S. Bureau of Mines has continually received inquiries about these products. At the request of other governmental departments it made tests in 1910, 1916 and 1930, using certain proprietary products applied according to the instructions of the vendors; these tests were made with eastern coals in domestic and

Jan 1, 1938

By A. J. Bartlett

Island Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, arid all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly arid continuously; that is, at all times while the mine!: are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are contacted in their working places and other employees at their respective, work. A thorough check is made to see that the state mining laws are complied with and that company safety rules arc being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emergency nature are taken up immediately with the management. Periodical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipmcnt and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture of the existing conditions at the time of inspection. Copies of inspection reports are forwarded to the superintendents with the general manager'? comments. It has been said, "There is nothing under God's heaven that justifies. your creation or your citizenship but this gospel: ' That the next greatest

Jan 1, 1938

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By E. L. Anderson, J. R. Long, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By J. S. Westwater

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W, within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleve-land-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. Al1en.† Mather " A " shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather "B," also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation. Shaft Sinking General Plan An average depth of 16 ft of sand overburden at the shaft site was cleared away by bulldozer, and the shaft approximately 15 by 20 ft in rock opening put down to an initial depth of 87 ft. Mucking of the broken rock to this depth was accomplished by an Insley excavator equipped with a 1/2 yard ca-pacity Owens clamshell bucket. Addition of 200 lb weight to each lip of the clam bucket provided adequate "bite" to dig the broken diorite and jasper rock. Temporary heavy wood bearers were placed across the shaft mouth to support the steel shaft sets which were hung in this initial 87 ft depth, aligned accurately and concreted in place from the lowest set upwards. The permanent steel headframe foundations and three service tunnel openings to the shaft were also concreted in the upper section to the shaft collar. A temporary wood headframe was then erected over the shaft mouth, and initial hoisting machinery assembled consisting of a Lake Shore 12 ft diam single drum grooved for a 1 3/8 in. rope and powered by two 400 hp motors to attain hoisting speed of 1100 fpm. Compressed air was obtained from a Nordberg 2 stage tandem horizontal type with a capacity of 1500 cfm. An enclosed landing platform at the shaft collar was equipped with a rotary dump and pocket for discharge of the rock into a Euclid 15 ton truck. On completing assembly of this equipment and installation of a special cage in the shaft, sinking was resumed on a three shift, six days per week

Jan 1, 1950

By Howard A. Meyerhoff, J. Earl Frazier

It is not known when silica sand was first noticed along the north coast of Puerto Rico, but the first mention of its occurrence was made in 1922, by N. L. Britton,1 who described its presence in isolated patches extending from Loiza westward beyond Manati. Further observations were made in 1925 and 1926 by Meyerhoff,2 who extended the known occurrences still farther westward to the low hill belt in the Quebradillas limestone immediately south of Hatillo. The extraordinary purity of the sands, which in most localities exhibit no contamination from the non-siliceous materials surrounding them, was quickly appreciated, and the feasibility of utilizing them for the manufacture of glass was investigated, initially by the Committee on Mineral Resources3 and later (1936) by the Puerto Rico Recon-structionAdministration and by H. C. Ray, mining engineer of the Insular Bureau of Mines. In 1934 samples submitted to the Hazel Atlas Glass Co., of Washington, Pennsylvania, were reported to have the composition as shown in the table on column two. Appreciation of the quality of the sand prompted geological and quantitative studies of the deposits, as well as cornmercial investigations to determine the feasibility of utilizing it locally or on the mainland for the manufacture of glass containers. Distribution of the Sands The quartz sands consistently lie within the outcrop area of the Quebradillas limestone, the youngest of the Miocene formations in the Tertiary coastal plain that fringes the northern coast of the Island. Many of the deposits are closely associated with limestone outcrops, but some appear to be embedded in lagoonal sediments at some distance from rock exposures, and at least one deposit, near Dorado, has been reworked by waves and littoral currents. With this single known exception, the deposits consist of irregular, patternless patches of white sand, which have sharply defined contacts with the surrounding material. Although patches of sand are present in a 90-km. belt that is not more than 5 km. wide, extending from Loiza to Hatillo, they attain maximum size, purity and number in the north central coastal area between Dorado and Barceloneta. Fifty separate deposits have been mapped in Lago Tortuguero and to the south of it, some as small as 50 ft. in diameter but

Jan 1, 1948

By A. E. Back

A method is described in which particulate iron, as distinguished from high purity iron powders used in powder metallurgy, is a precipitant for copper contained in dilute solutions. A new precipitation apparatus utilizes particulate iron precipitants to recover copper more efficiently than is possible in a conventional launder precipitation plant. In the search for lower cost methods of recovering copper from mine water, the use of sponge iron or particulate iron (as distinguished from iron powder used in powder metallurgy) as precipitants in place of tin cans, detinned scrap iron, or scrap iron is an intriguing possibility. The relatively faster copper precipitation rate obtained with particulate iron as compared to scrap iron promises economic and processing advantages when, and if, particulate iron becomes competitive cost-wise with available scrap iron. Kennecott has developed a precipitation cone,' see Fig. 1, utilizing various particulate iron precipitants and has demonstrated the process successfully in a prototype at a flow rate of approximately 1000 gal of solution per min. Essentially complete precipitation of copper is obtained, the cone overflow solution is clear and contains no particulate copper, and the iron factor is more favorable than in a conventional launder plant. Initially, sponge iron produced at the Ray Mines Div. Kennecott Copper Corp. for use in a Leach-Precipitation-Flotation process was used in exploratory tests to develop a suitable apparatus to take advantage of the rapid precipitation rate and efficient iron utilization for the recovery of copper from dilute solutions. Here it was demonstrated that, when sponge iron was added to a launder, the particles of iron collected in the bottom of the launder and tended to cement together. This resulted in incomplete precipitation of the copper and inefficient utilization of the iron. Next, sponge iron was suspended in glass columns to study the dynamics of the precipitation reaction. Again it was observed that the particles tended to cement together at low solution flow rates, while at higher flow rates large amounts of the precipitant overflowed the column, resulting in loss of precipitant and an inefficient process. Next, the precipitant was suspended in an inverted cone in a rising column of solution. Dynamic suspension of the solids was maintained at relatively rapid solution flow rates with instantaneous and complete precipitation of copper and with improved iron utilization. The first tests were conducted on a batch basis and it was determined that a dynamically suspended bed of precipitant was necessary for satisfactory operation. More than 99% of the metallic iron could be converted to metallic copper by careful control of the residence time in the cone and copper precipitation was essentially complete, even when the available iron precipitant was almost depleted. Several cones were built, ranging in capacity from 1 to 200 gal of feed solution per min, and finally, a prototype cone was constructed which was 20-ft high

Jan 1, 1968

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -The Institute was founded 54 years ago "with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained" At least once a year it is well to take stock of our assets, review our performance and determine how well we are now carrying out the purposes of our Founders There can be no question as to the work the Institute has done and is doing in promoting the arts and sciences in the fields of mining and metallurgy One needs only to contiast the methods, the labor and the costs of a half century ago with those now to visualize how far we have gone in the development of accurate technology and sound economics in mineral and metal production The great mines, mills and smelters of the present, handling individually thousands of tons per day, would have been impossible except for the accumulation of knowledge, the development of theory, and the improvement in practice that has charac¬terized the period since the foundation of the Institute The United States has prospered in the last half century greatly, and this has been due not merely to the possession of great natural resources, but to these resources being reduced to possession and put to work The absence of customs barriers and the freedom of trade across the whole width of this great continent has been an important factor in the growth of our wealth Unrestricted interchange of goods has permitted each citizen to draw on the resources of the whole country However, these are but subsidiary causes of prosperity The free interchange of scientific and technical data, by making the whole body of facts and theory available to each worker, has made this quick and unrivaled development possible In promoting this free trade in knowledge the Institute may claim a large place without fear of denial The 72 volumes of TRANSACTIONS, the special volumes, the bulletins and the other pub¬lications that have been issued, include a store of knowledge of the arts and sciences related to the pioduction and use of metals and minerals not duplicated elsewhere The large list of foreign members-1746 in number-few of whom ever have opportunity to attend meetings and all of whom derive their main benefits from membership through the pub-

Jan 1, 1923

By Ralph J. Schilthis

Several investigators1-8 have reported evidence of the existence of native or connate water in oil-and-gas-bearing strata. Both water and salt have been detected in cores of oil sands that yielded oil and gas exclusively when produced. Electrical logs often reveal unexpectedly low resistivity through oil and gas sands, indicating the presence of some material that is a considerably better conductor of current than oil and gas. Furthermore, calculationsg of the oil and gas content of reservoirs based upon production and reservoir-pressure decline data indicate appreciably lower values than are arrived at under the assumption that the pore space is occupied completely by oil and gas. Origin and Occurrence of Connate Water in Oil-and-gas-bearing Formations The view has been expressed, 10-15 and is generally agreed upon, that the expulsion of oil and gas material from source beds and the subsequent migration and accumulation occurred in the presence of salt water. As the strata that usually form reservoirs for oil and gas were laid down by, or in the presence of, ancient seas, the pore space within the strata must have been saturated with salt water before the entrance of the oil and/or gas. Thus, the accumulation of oil and/or gas in the upper regions of structures suitable for reservoirs must have required displacement of the connate water therefrom. In the absence of any forces other than gravitational, it would be expected that the displacement of the connate water out of the zones finally occupied by gas and oil would be complete, and that the vertical distribution of gas, oil, and water in a reservoir would be strictly in the order of their densities. Apparently, however, surface and interfacial forces that will not permit complete segregation of the fluids are active within the capillary spaces comprising a reservoir. The effects of these forces on both accumulation and production of oil and gas have been the subject of study by a number of investigators.16-37 In general, the view is held that the character of most materials that make up the reservoir rock leads to preferential wetting of the rock by

Jan 1, 1938

By R. F. Janke, J. F. Bossler

Introduction The commercial use of ion exchange resins to recover uranium evolved in the decade following 1950 when significant efforts were made to recover this vital element economically and efficiently from low grade ores. It was discovered that in both acid and alkaline systems, uranium exists as an anionic complex. This led to the application of anion exchange resins to concentrate and purify the uranium product. While this is the simplest statement of what an ion exchange resin does in the recovery of uranium, it should not be forgotten that the industry is continuing to evolve new methods in mining and processing which affect ion exchange operation. The inception of solution mining, the use of expanded bed ion exchange columns and the development of continuous ion exchange systems represent several examples of this continuing evolution in the industry. Throughout all of the changes in equipment designs and variations in solution compositions, the purpose of the ion exchange resin remains the same - to concentrate and purify uranium. Ion Exchange Resins When evaluating ion exchange resins for a uranium recovery project, the task that faces the chemist or process metallurgist is an assessment of the efficiency and, therefore, the economics of the various candidate resins for a given project. This assessment should include consideration of both physical factors such as particle size, density, hydraulic expansion and pressure drop as well as chemical factors such as the uranium loading and elution characteristics. For any given application, the differences in the physical and chemical behavior of ion exchange resins are a function of the conditions used to manufacture those resins. Therefore, an understanding of the way in which manufacturing variables affect resin behavior is important. Since most uranium recovery projects are concerned with recovery of the anionic complexes of uranium using anion exchange resins, this discussion will be restricted solely to the family of anion resins. The majority of the ion exchange resins used in commercial recovery operations look similar to the resins shown in Figure #1. [ ] Most of these materials are based on a styrene- divinylbenzene copolymer. The liquid monomers, styrene and divinylbenzene, are charged to a co-polymer reactor containing water. The water insoluble monomers are then mixed with the water to suspend oil-like droplets of the monomer mixture in. the water. The entire reaction mixture is then heated causing the monomers to polymerize into sol id thermoset plastic spheres. The spherical nature of the particle, the particle size distribution and the primary crosslinking level are fixed in this step in the production process. Figure 2 is a simplified illustration of this step of the process. [ ]

Jan 1, 1979

By G. W. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro- static separators and air flotation or air tables. MAGNETIC SEPERATORS In general, separating is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 980, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1938

WHILE papers on cleaning coal and mining coal were presented at the iron and steel and mining methods sessions, respectively, the first general session on coal was held on Wednesday afternoon. Howard Eavenson of Pittsburgh, Pa., as chairman of the session,* reported progress by the Committee on the Valuation of Coal for Blast-Furnace Coke. A paper on blasting coal effectively and safely in Southern Illinois, by J. E. Tiffany and S. S. Lubelsky, was abstracted and commented on by Dan Harrington, of the U. S. Bureau of Mines. W. J. German commented on some conditions mentioned in the paper as unsafe or bad practices, and added to these some further ex-amples; he made a strong plea for holes to be: drilled parallel to the bedding as the easiest way to determine the proper length or depth to agree, with the depth of kerf cut. Mr. Barron called attention to proper cutting and-drilling and rate of detonation of the explosive used, as effective aids in blasting coal. Another speaker mentioned an odd case where compressed black powder or "pellet powder," had decreased accidents at a non-gaseous mine where permissible explosives had been formerly used; the permissible cracked or shattered the roof, with a resulting high accident rate from falls of roof, and pellet black powder overcame this trouble. Eugene McAuliffe of the Union Pacific Coal Co. told of difficulties in changing from black powder to permissible in Wyoming mines. J. B. Dilworth read a paper on valuation of coal prop-erties, expressing a preference for the method of capi-talizing the earning power of a property. Eli T. Con-ner of Scranton, Pa., with much experience in valuation work, stated that the method was undoubtedly good, but many times failed because of inability to forecast accurately future earnings, and further contended that total valuation -and royalty rates could generally be fixed fairly when based on similar neighboring proper-ties' rates when these had recently been established by a free bargaining. S. A. Taylor of Pittsburgh, Pa., stated that a leasehold value could be fairly established by figuring based on 10 to 20 per cent of the profit resulting from operation. The chairman read a written discussion from Henry Louis of England, called atten-tion to differences in valuation resulting from whether gross or net profit or earnings were used as a basis for capitalizing. John A. Garcia of Allen & Garcia gave a most inter-esting account of coal mining and general conditions in Russia as noted in his recent extensive visit there, which appears elsewhere in this issue. Although agree-ing with most thinking Americans that government operation is incompatible with progress, he showed that mining conditions were far from impossible in present-day Russia. Charles E. Stuart gave motion pictures of parts of the trip, with, his own comments supple-menting those of Mr. Garcia.

Jan 3, 1928

By J. G. Tilton

While most of the Pittsburgh coal horizon is dependably regular, there are areas where it is dis-turbed by sandstone cutouts which can seriously hamper mining operations. Because these channel sandstones often cut out the coal abruptly, they are difficult to detect by core drilling; and mine operators, for want of a better way to discover them, have largely trusted to luck to avoid them. This paper, based on a study the author is presently conducting, is an attempt to point out some sources of information and signposts which might aid the operator in determining the presence of a cutout before he begins to mine. The presence of sandstone cutouts in the Pittsburgh coal has been known for many years. Some of these irregularities were observed at outcrops and others were discovered by drilling, but the majority were and are found during mining operations. These sandstone cutouts are commonly called "faults" and have been a bane to mining companies wherever they have been encountered. Profiles of some typical deposits appear in Fig. 1. The cutouts disrupt the normal system of mining, replace valuable coal reserves, create ventilation problems by emitting large quantities of gas and sometimes oil, limit the number of entries that can be economically driven, affect the quality of the coal, disrupt the normal structure of the coal, and create roof control problems. It might be expected that such severe disturbances in the structural regularity of the coal would instigate determined and extensive searches for possible cutouts prior to mining operations, but this apparently has not been so except in isolated cases. Two reasons may be cited to explain this lack of exploratory work. The first and probably the strongest reason is the over-all regularity of the Pittsburgh coal. No coal seam in the country exhibits the horizontal continuity and relative regularity of the Pittsburgh coal. It lies in an almost unbroken sheet across southwestern Pennsylvania, eastern Ohio and northern West Virginia, and has been recognized as far east as the Potomac Basin of western Maryland. Over 5729 square miles are underlain by this coal, of which 2077 square miles are in Pennsylvania, 2214 square miles in West Virginia, 1410 square miles in Ohio, and 28 square miles in Maryland. The area covered by this study is outlined by the map in Fig. 2. Over most of this territory the coal has the following characteristic structure as illustrated in Fig. 3: roof coal, draw slate, breast coal, parting, bearing in coal, parting, brick coal, parting, and bottom coal. With such regularity of thickness and structure, mines were opened and laid out with confidence that the coal would be present. Extensive drill testing was considered unwarranted and it was also quite expensive because the coal dipped to the west away from the Monongahela River. Consequently, drill holes were widely spaced and rarely encountered ad-

Jan 1, 1968