Search Documents

By Richard McCaffery

THIS paper considers certain aspects of the acid Bessemer process, particularly in its relations to the duplex process-that combination in which the pig iron is first desiliconized and decarburized in acid Bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid Bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide. On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not make the bottoms of basic or neutral material?1 As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 8, 1920

By T. R. Young, S. A. Scott

9.5-1. Introduction. The use of pipelines to transport solids has been successfully accomplished with many different materials. One of the oldest applications is the dredging and placing of hydraulic fill. Many installations have been made and operated for long periods of time with excellent dependability, low operating cost, and low maintenance. It is not the aim of this chapter to give the engineer the answers from which to design a pipeline, but rather to supply helpful information from which to start the project. There are several phases of solids pipelining which as yet have not lent themselves to quick engineering answers. Investigations have been carried on by many, with several theories advanced by the various investigators. In recent years certain notable theoretical advances in hydraulic transportation have been achieved. Vertical transport, using balanced "leg" operation, now appears competitive with other forms of vertical transportation. In addition, horizontal transport utilizing capsules has been proven experimentally to be attractive because of lower pressure drop than the conventional methods of solid transport in fluid media. With the aid of the computer, the laborious calculations associated with pumping calculations have been greatly simplified; and with this tool the pipeline engineers of the future will undoubtedly be able to develop a more comprehensive understanding of solids-fluid transport. 9.5-2. Theory. There have been many excellent studies made and information is available in the literature, but a general comprehensive theory of pipeline transportation of solids has not been advanced. The existing flow theories will give approximations for minimum and optimum flow velocities, friction head losses, energy requirements, and pump and pipe size The principles of dynamic similarity and scaling laws are well understood for the flow of pure liquids. There are no firm methods of scaling slurry pipelines of small diameter to larger diameters except for a few empirical.

Jan 1, 1968

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By Joseph Jensen

When the legal holders of Government permits in the Middle dome of Kettleman Hills entered into an agreement on May 27, 1929, to suspend all drilling activities on five permits, covering portions of the Kettleman Hills Middle dome, until Jan. 1, 1931, and the owners of fee lands contiguous thereto assured Secretary Ray Lyman Wilbur, of the Department of the Interior, that they too would respect a drilling suspension for a period of a little more than 19 months, none of these interested parties realized that this was the first step in a chain of events that would culminate, more than four years later, in the formation of the Middle Dome Corporation for the development of the Middle dome area in a unit plan that would be the first unit plan to be approved by the California Regional Producers Committee and recommended to the President as a satisfactory unit plan, under Section 7 of Article III of the Oil Code, approved Aug. 17, 1933. Neither did they realize that more than two million dollars would be spent before oil or gas would be successfully and continuously produced from wells drilled on that Middle dome area. On Oct. 1, 1933, under the terms of the Middle Dome Agreement, the Middle Dome Corporation assumes control of activities and is responsible for the division of all product's produced from the Middle dome area to members of the Middle Dome Corporation. This Middle dome plan is the second successful unit plan developed in California in the past three years, the first being the Kettleman North Dome Associationll formed under the agreement, of Jan. 31, 1931, for the unified operation and development of more than 12,000 acres of land on the North dome of the Kettleman Hills. All other unit plans discussed in the past four years in the state have not yet been completed, for one reason or another, but under Section 7 of Article 111 of the new Oil Code numerous plans of development, some of which may be unit plans, will be forthcoming within the next few months. There is much

Jan 1, 1934

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By Jesse Betterton

IN the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200° to 1300° F. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accom-plish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flow of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The, process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes.

Jan 1, 1933

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By R. W. Raymond

The western public domain acquired by the United States through trcaties, as the result of conquest or purchase, was invaded after Marshall's re-discovery of gold in California, by an overwhelming multitude of prospectors and miners from all parts of the world. he mineral lands of the whole Pacific slope were practically unsurveyed. Congress, disgusted with the experiment of leasing mineral lands, which it had tried for 40 years, and abandoned in 1847, enacted no laws for the management of these public mineral lands, and the pioneers made their own laws governing mining titles. These local regulations applied at first to gulch-mining in the auriferous river-beds only; and they constituted a simple and practical system. adapted to the needs and means of primitive communities—significantly called " camps." They had the means of measuring distances, but not angles; they knew no property except personal property in the form of pickaxes, pans, supplies, camp-equipage, horses or mules, and mining rights. The earliest codes which they developed expressed what might be called the law of the lariat. With the lariat they measured the distance assigned to each miner along the gold-bearing gulch—a double portion to the discoverer, and a single portion to his successors, in the order of their coming. With the lariat, they hung, after such due process of law as was available, the rascal who stole a horse, or a bag of gold-dust, or a mining claim, or killed another man without giving him fair notice and a chance to defend himself. In these pioneer codes, adopted in mass-meetings and enforced by the same authority, two features concern us most: 1. They measured mining property by one dimension only. So many feet of the gulch, held by one man, meant a distance into either bank, and a distance in depth, extending as far as gold might be found.

Jan 1, 1915

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By S. C. Geol, C. H. Page

INTRODUCTION Mining at Mindola Mine, Rokana Division of Nchanga Consolidated Copper Mines Limited is the deepest on the Zambian Copperbelt. Mining extends to 1150 metre depth so far and the present plans extend to 1500 metres, although reserves exist below this level. Mindola Mine is the major producer of copper/cobalt ore at Rokana Division and produces approximately 200,000 tonnes of copper/cobalt ore per month. A standard open stoping method is the only method used for mining with minor variations in positioning drilling drives and other development, figure 1. The standard main haulage interval is 75m but in flat dipping areas the full stope height is split into two or three panels. In 1970 severe mining problems were experienced when mining deeper than 850111 below surface. The main problems included: - Heavy support requirements in drilling drives near stope face. - Premature closure of blast holes necessitating pre-charging of the holes with explosives immediately after drilling and well before the day of blasting. - Severe bumping and spitting due to rock movements on drive surfaces and remotely within the rock mass under high stress. - Low mining efficiency due to dilution from the waste hangingwall. - These stress related factors also caused some premature detonations of precharged but unprimed blast holes which became a serious safety hazard. A number of alternatives have been considered to overcome these problems. A search for leas sensitive explosives to avoid the premature detonation problem has been partially successful, however, the need for a method of reducing stress levels at the mining face is still considered essential as the mine goes deeper. This paper describes experiments with Regional Support Pillars as a method of reducing stresses at the mining face.

Jan 1, 1981

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By S. Frederick Ravitz, Kenneth E. Fisher

Four liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constituents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equilibrium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest. In order to ascertain whether equilibrium existed, the distribution of gold and silver among the four liquids was determined. The speiss,

Jan 1, 1937

By B. C. Burgess

AFTER many years of close and friendly association with talc and soap-stone, this orthographically distinguished mineral steps forth in this edition, for the first time in a chapter of its own. Pyr, the Greek for fire, and phyllite, a rock or stone, form its name and at the same time refer to the first recorded use of pyrophyllite as firestones or hearthstones. Another derivation of "phyllite" is from the Greek phyllites, "of leaves," alluding to the beautiful white radial crystal aggregates that form when pyrophyllite is heated. Pyrophyllite used by the Chinese for carving is called agalmatolite, from the Greek agolma, meaning an image. COMPOSITION AND PROPERTIES Pyrophyllite has previously been grouped with talc because of the close similarity of the minerals in physical and optical properties. They have the same space group; and chemically they are closely related, pyrophyllite being the aluminum silicate A12Si4010(OH)2 and talc the magnesium silicate Mg3Si4010 (OH) 2. Another arrangement of the pyrophyllite formula is generally given as A12034Si02H20 because it expresses the chemical composition as usually determined (alumina 28.3 pct, silica 66.7 pct, water 5.0 pct). Vanderbilt gives pH values of pyrophyllite 5.6 to 8.4.29 Pyrophyllite usually is white, pale green, cream or pale yellow, buff or light gray. It is found in darker shades and other colors principally due to oxidation of contained iron minerals. It is translucent in thin sections. In hardness it is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. In bulk specific gravity, the powdered mineral ranges from 0.4 to 0.7. Its luster is pearly to dull; it is infusible in the Bunsen burner flame, slightly affected by aqueous solutions of sodium carbonate and hydrochloric acid. It is decomposed by sulphuric acid, with separation of gelatinous silica. It is characterized chiefly by its micaceous structure and cleavage, its softness and greasy feel. Two other varieties occur

Jan 1, 1949

By J. E. Lawver, R. R. Beebe, J. L. Wright

This paper describes a separation coefficient Ks useful as a "measure of goodness" to be used in factorial and response surface methodology. The use and limitations of the separation coefficient is discussed, and a computer program for calculating the coefficient is presented (in Fortran). The application of the coefficient is illustrated in terms of electro-dynamic separation of Mesabi semitaconites. Present Mesabi wash ores and gravity concentrates with an iron to silica ratio of only 5 or 6 to 1 are no longer readily salable, for the steel industry now demands concentrates with an iron to silica ratio of at least 10 to 1 and a structure comparable to pellets. THE ELECTRODYNAMIC-FLOTATION PROCESS Wash ores and gravity concentrates consist largely of hematite, goethite, and quartz. Several methods of beneficiation are being tested at the University of Minnesota Mines Experiment Station with a view to improving the salability of these materials. A process that looks particularly promising from an economic view is the combination electrodynamic-flotation process shown in Fig. 1. This process is designed to upgrade gravity concentrates to a 5% silica content and to provide fines — from the flotation circuit —to permit agglomeration. Although electrodynamic concentration of specularite is an established and well-understood process, the electrodynamic concentration of Mesabi goethite-hematite gravity concentrates presents interesting and enigmatic problems. The gravity concentrates are by no means assemblages of clean, free mineral particles. Instead, the concentrates to be retreated consist of a great variety of middlings. More or less complete liberation would require grinding to minus 325 mesh, at which size only flotation could be expected to function, and even then grades and especially recoveries would not be satisfactory. A close examination of the gravity concentrates shows that grinding to 100% minus 48 mesh will produce a product which is approximately 70 weight % plus 325 mesh (see Fig. 1). The remaining 30 weight % can be deslimed and floated by conventional methods, but the resulting iron concentrate is

Jan 1, 1964

By J. H. Nead

The subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. In most other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were takcn every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in Table 1. All domestic scrap was used and the charge was made up as follows: Head End Finish Pounds Pound Pig iron........................ 36,300 Pig iron....................... 23,900 Sheet scrap bundles............. 36,200 Sheet bars..................... 23,900 Sheet bm..................... 40;200 The total charge, exclusive of the re-pig added near the end of the heat, was 160,500 Ib. The limestone charged was 21,400 Ib., or 13½ per cent.

Jan 1, 1924

By W. L. Phillips

Aluminum and copper single crystals were strained in shear, unloaded and rotated 60, 120, and 180 deg. The magnitude of the Bauschinger strain increased rapidly during the easy glide region and became constant as the easy glide limit was reached. An increment in stress was not required to continue slip in any close-packed plane or in the reverse direction during easy glide. A qualitative theory is proposed to explain the present results. FOLLOWING the initial work on tin by Bausch,' there have been several investigatorsB7 who have employed the shear test to study the deformation of aluminum. In all cases the shear technique was employed in an attempt to obtain a more homogeneous shear than in the conventional tension test The direct shear technique has the obvious advantage, relative to the tension test, that a crystal may be stressed in any predetermined plane and direction, including the reversal of strain sense. In the present investigation the shear technique was employed with aluminum and copper single crystals and their behavior was studied with respect to deformation in all close-packed directions in the octahedral plane. In contrast to previous investigations, the shear technique was used in an attempt to obtain a stress-strain curve in shear which is identical with the corresponding tension curve and then to use the additional degree of freedom of the shear test to study the mechanical behavior of crystals in all close-packed directions in the octahedral plane. PREPARATION OF CRYSTALS Single crystals 1/2 in. in diam and 6 to 7 in. long, were prepared from aluminum containing 0.001 pct Si, 0.001 pct Fe, and 0.001 pct Zn, by spectro-graphic ana1ysis and from OFHC copper. Crystals were grown from the melt in graphite at a rate of 1 5 in. per hr. The copper crystals were grown under an argon atmosphere. No lineage structure was observed in Laue patterns, though small angle boundaries were present in the crystals. The aluminum and copper crystals were annealed at 640" and 900°C, respectively, for 24 hr and furnace-

Jan 1, 1962

By F. V. Hicks

THE similarity of mining practices in bituminous coal fields through-out America is due to the fact that certain fundamental conditions are encountered in all fields. The problems of labor, housing and mining are somewhat similar whether the mine is in Pennsylvania, Illinois, Wyoming or the State of Washington. Each field has had its particular problems, resulting in advantages or disadvantages over a competing field. This might take the form of a wage differential, a better natural condition more favorable to cheap production, or proximity to a market that allows freight rate advantages, etc. In any event, no matter how favorably situated, the mining companies that have been slow to recog-nize and accept the advantage of mechanization, clinging too long to the old hand methods, have found themselves unable to meet competition. Throughout the Wyoming coal fields, production methods have so changed in the last decade as to be almost unrecognizable to an old-time coal miner who has had no connection with the industry during; that period. The old contract system, with its peculiar labor relationship between employer and employee, based upon the long-established custom that the miner's working place was his castle, and that it was his privilege to carry on operations within that place largely in his own way and to his own liking, is a condition that has passed away. The present-day, 100 per cent mechanized mine bears but little resemblance to the old. A change -in system has naturally altered the old-time labor relationship. Contract labor has been almost entirely eliminated and a straight day-wage basis established, with certain classes of work calling for different rates, which places the entire personnel of the underground operating force more directly under the direction and supervision of the mine foreman and his assistants. The transition from the old order to the new has gradually done away with the system of penalties, personal- rights and privileges existing under the contract system, which were so controversial in the past that the average mine management was constantly involved in labor disputes in fields where organized labor was employed.

Jan 1, 1936

By John B. Pearse

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway Managers determined on and have long applied a test of 1000 pounds falling 101 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails from our most reliable makers, break under a 6 foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 13 1/2 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent, of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. In England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariably

Jan 1, 1873

By John M. Hartman

The high temperature of the blast of modern furnaces renders it desirable that the pipe conveying the blast into the furnace crucible shall transmit and radiate as little heat as possible. To accomplish this, the pipe shown in the accompanying sketch was devised and patented. It consists of a slide-valve, leg-pipe, and belly-pipe, which are held together and to the tuyere by a system of levers and links. The slide-valve is superior to the old throttle-valve. The legpipe is formed of two thicknesses of wrought-iron pipe, with a space of half an inch filled in with clay and brick. The belly-pipe is made in the same way as the leg-pipe, and terminates in a globe face to suit the tuyere. The quarter turn is made extra thick, of cast iron, and the cap on the end is lined with clay also. The catches, A, B, C, are merely for convenience in putting the pipe together. The joints D and E are globe faces, and allow the pipe to adjust itself to any angle. The eye-piece is made of violet glass, which cuts off the glare from the bright coals in the furnace and allows a close examination of the interior, so that any water dropping or vapor can be detected. The glass does not become coated with dirt, like mica. Since good running of furnaces is shown by a bright tuyere, it is necessary to have a good eye-piece to examine them. To detach the pipe, a man lifts the weights, the side rods are then slipped off the bell crank under the quarter turn, the link under the belly-pipe is unhooked, and the pipe carried away. The same process is reversed to put the pipe together. The nozzle is changed by taking off the cap, G, drawing the nozzle through the belly-pipe, and inserting another. In this way the change can be made quickly, without taking down the pipe. On the old tuyere pipe bolts with brass nuts were used, which burned up and gave trouble. In other cases key-bolts were used, making it difficult to adjust the pipe. Bolts make too rigid a joint, and there is no provision for movement from contraction or expansion. As the temperature of the blast increases there is more expansion, and where rigid joints are

Jan 1, 1879