Search Documents

By R. Schuhmann, E. J. Michal

Experimental measurements are reported for the oxygen pressures of iron-silicate slags in equilibrium with solid silica. CO2-CO mixtures were bubbled through the slags in silica crucibles to find equilibrium values of p co2/p co over the entire composition range of silica-saturated slags at 1250°, 1300°, and 1350°C. From the data, the activity vs. composition relationships were calculated for O, FeO, and Fe. SLAGS composed primarily of silica and iron oxides have particular practical importance in copper smelting,' in acid steelmaking, and in accounting for the service behavior of silica refractories. These slags all contain both ferrous and ferric iron, so that, strictly speaking, they are ternary or three-component liquid solutions. For convenience, the components may be taken as the three oxides, FeO, Fe2O3, and SiO2. The constitution of the FeO-Fe,O,-SiO, system at slagmaking temperatures has been studied in a recent investigation described in a separate paper.' This work showed the compositional ranges of iron-silicate melts at temperatures up to 1450°C and also the temperature-composition relationships for melts in equilibrium with various solid phases, including iron, wüstite, magnetite, and silica. Broadly speaking, the compositions of iron-silicate melts at a given temperature should be thought of as varying over a two-dimensional field. In the first place, the silica/total iron oxide relationship varies from maximum silica for silica-saturated melts to minimum silica for wüstite-saturated melts or, at higher temperatures, to zero silica for straight iron oxide melts. In copper smelting, for example, the converter slags approach the low silica limits while the reverberatory-furnace slags have intermediate silica contents, perhaps approaching silica saturation in some circumstances. Liquids formed in the pores of silica refractories presumably are close to silica saturation. The second type of composition variation is in the ferric/ferrous relationship, which depends on how oxidizing or how reducing the process conditions are. Relatively reducing slags, such as acid-steelmaking slags, are lower in ferric oxide and ap- proach saturation with metallic iron. Oxidized slags, such as copper-smelting slags, contain larger percentages of ferric oxides and approach or reach saturation with magnetite. Since these two kinds of compositional variations are closely related to two general properties of interest for all metallurgical slags, basicity, and oxidizing power, it is hoped that the thermodynamic study of iron-silicate slags eventually will throw further light on the significance and nature of these long-recognized but as yet poorly understood slag properties. Measurements of oxygen activity as a function of slag composition, using CO-CO2 gas mixture to fix oxygen activities, afford an experimentally convenient approach to the study of the thermodynamic properties of iron-silicate slags. In a preceding investigation,³ his approach was used in a systematic study of iron-silicate slags in equilibrium with solid iron. The present paper gives the results of a similar study of the iron-silicate slags in equilibrium with solid silica. The experimental work consisted in the determination of CO2: CO ratios in gas mixtures at equilibrium in the system: gas: liquid slag: silica Determinations were made at temperatures from 1250° to 1350°C for slags ranging in composition from iron saturation to magnetite saturation. Also, equilibrium CO,: CO ratios and slag compositions were determined for the univariant systems: gas: liquid slag: silica: iron gas: liquid slag: silica: magnetite Experimental Methods The experimental procedure was essentially the same as that used in the previous study of iron-silicate slags saturated with solid iron," but in order to work with the silica-saturated slags an all-silica crucible assembly was used. A liquid slag was prepared from pure prefused stock materials and brought to equilibrium with the silica crucible at the desired temperature. Then a mixture of CO2 and CO was continuously bubbled through the melt

Jan 1, 1953

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By C. R. McEwen

This paper presents a technique for calculating the original amount of hydrocarbon in place in a petroleum reservoir, and for determining the constants characterizing the aquifer performance, based on pressure-production data. A method for doing this based on a least-squares line-fitting computationwus proposed by vanEverdingen,Timmerman andMcMahon in 1953. We found that their method would not work when there is error in the reservoir pressure data — even moderate error. The technique presented here appears to give reasonable answers when pressure data are uncertain to the degree expected in reservoir pressure determinations. The major change introduced in the present analysis is to limit the least-squares line-fitting to yield only one constant— the amount of hydrocarbon in place. The water-influx constant is then taken as proportional to the oil (or gas) in place. The constant of proportionality can be computed from estimates of effective compressibility and reservoir water saturation. It is also pointed out that the commonly used least-squares analysis assumes all of the uncertainty to be in the dependent variable. The material balance should be arranged so that this condition is fulfilled if correct inferences are to be made from statistical calculations. Examples are shown of the application of the new technique to gas reservoirs—both hypothetical and real—and to the oil-reservoir example of van Ever-dingen, Timmerman and McMahon. INTRODUCTION The amount of hydrocarbon originally in place in a petroleum resenroir can be estimated by means of the material-balance calculation. Simultaneous observations of pressure and amounts of produced fluids are required, together with the PVT data applicable to the reservoir fluids. If water encroachment is occurring, it is desirable to try to infer the behavior of the aquifer, as well as the original hydrocarbon in place, from the pressure-production data. This imposes additional demands on the method of calculation, and uncertainty in the data can result in large uncertainty in the answer. In addition, if the size of a gas cap is to be established, the whole problem becomes indeterminate, as pointed out by Woods and Muskat.1 Brownscombe and Collins2 simulated a gas reservoir and its aquifer on a reservoir analyzer and derived quantitative information on the effect of uncertainty in pressure and aquifer permeability on computed gas in place. Among the various techniques of estimating the performance of an aquifer, the method of van Ever-dingen and Hurst? based on compressible flow theory, seems to have been the most generally successful (see Ref. 4, for example). In this paper we shall confine ourselves to their representation of the aquifer. In 1953,' van Everdingen, Timmerman and McMahon5 introduced a statistical technique for deriving the amount of oil originally in place and the parameters which describe the aquifer. (We shall refer to this technique as the "VTM method'', as suggested by Mueller.6) Their example reservoir had no gas cap. It has been our experience that the VTM method gives a reasonable answer when the data are very accurate, but that inaccuracy (particularly in pressure) can cause the method to break down. The effect was first observed in gas reservoirs, but has since been seen in oil reservoirs also. In this paper we present another statistical method which has been successful in achieving a reasonable answer where the VTM method has failed. In the new method, one less parameter is derived from material-balance computations. It is assumed that values can be established for effective compressibility in the aquifer and reservoir water saturation independently of the material-balance calculation. The water-influx constant can then be obtained from these data and the quantity of hydrocarbon in place.

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By Herbert W. Huse

Nitrogen, and its compounds, unique among the materials described in this volume, is absolutely essential to the existence of the human race. Almost all minerals are important and the absence of any one of them would be sorely felt; but nitrogen is an integral part of the cycle of life itself. Man cannot live without nitrogen which, as an inert gas, composes the major part of the air he breathes; as compounds, nourishes the vegetation which he eats; and, as protein, forms a part of his very flesh and blood. Nature originally provided man with a vast reserve of usable nitrogen compounds in the form of fertile soil. She constantly replenishes the supply by "fixing" nitrogen in the air at the estimated rate of 400,000,000 tons per year (an insignificant 6 lb per acre) during electrical storms. She has also placed certain microorganisms in the soil which are able to "fix" nitrogen and convert it into forms which plants can use. Legumes like cow peas, soy beans, clover, and alfalfa have extraordinary roots which serve as stimulating hosts to these bacteria which, in turn, nourish the plant. By plowing in all or part of such crops, their above-average nitrogen content can be returned to the soil for other more useful crops. The mechanism for this recycle is supplied by "denitrifying" bacteria which attack the dead plant tissue and liberate nitrogen and ammonia. However, since one crop of grain, sugar beets, potatoes, tomatoes, etc., takes out a major portion of the nitrogen which a plowed-in legume crop can supply, this method of fertilization is obviously inadequate. Drastic intervention by man has become necessary to support the ever-growing population of the world.9,15,20 Old civilizations with a high population density, such as the Chinese, were able to exist for centuries by carefully tilling the soil, rotating crops, and returning to the soil all the nitrogen in vegetable wastes plus human and animal excreta. But the lack of a means for augmenting their supply of nitrogen placed a ceiling on further development and kept the mass of the population in a chronic state of undernourishment, frequently punctuated by famine. Nitrogen plays another important role in the life of mankind. In the form of explosives, nitrogen helps to wrest from the earth many materials needed for our material well-being. Also, in the form of explosives and propellants, nitrogen increased the destructiveness of wars to a point only exceeded by the fantastic power of atomic energy. Man's first really effective efforts to improve his position with respect to nitrogen began in the 18th Century with the mining of sodium nitrate. By the late 1880's this had become a big industry serving a large part of the world. In the late 1890's nitrogen, in the form of ammonia, was being recovered from coke-oven operations. In 1900 nitrogen, in the form of nitric oxide, was being obtained from the air by an electric-arc process. About 1904 another "fixation" process based on the reaction of nitrogen with calcium carbide to form cyanamide was commercialized. By 1913 the Haber-Bosch process of "fixing" atmospheric nitrogen by reacting it with hydrogen to produce synthetic ammonia was successfully applied on a large scale, first in Germany and then throughout the industrial areas of the world.9 All the above methods of obtaining nitrogen compounds are still in use and, between them, they assure mankind of adequate supplies for all time. While this fortunate situation is not unique amongst industrial raw materials, all too few of man's needs are so well in hand.

Jan 1, 1960

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By D. G. Oss, S. E. Erickson

An automatic control method for the ferrosilicon heavy media process maintains media density within 0.01 specific gravity points. Continued demands for higher grade, competitive products from the Mesabi Range have resulted in experimental work such as that detailed for one concentrator. Various methods, step by step procedures and instruments used at an iron ore beneficiation plant in the development of an automatic control system are described. Work continues and it is hoped that further applications of control instrumentation can be made in the next operating season. The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. In a typical heavy media flow scheme for iron ore beneficiation (Fig. 1) a sized, prepared feed (generally about —1% in. to +% in.) is fed to a heavy media separatory vessel, along with a ferrosilicon slurry. A separation of the feed is made on the basis of specific gravity. Low density particles overflow a tailings discharge weir, while high density ore particles sink to the bottom of the high density pool and are moved away to the concentrate discharge chute. Both products are passed over drainage screens and then are cleaned thoroughly of attached ferrosilicon on wash screens. Float material is generally stockpiled, while the sink product is shipped as a final concentrate. Undersize from the drain screens is returned directly to the circulating media sump. Wash screen undersize is cleaned of contaminating ore particles and slimes by passing through magnetic separators. Provision is also made for splitting a portion of the tailings drain undersize into the cleaning circuit if necessary for control of depth of tailings overflow, or for additional cleaning as required. Cleaned ferrosilicon is stored in a densifier and returned to the Circulating media sump as make-up material. Dilution water is also added to this sump to maintain a desired specific gravity of the circulating media. As in any process, operational intelligence is secured only by keeping records of the process variables. Generally apeaking, plant operators have neither the inclination nor the time to keep complete and detailed records of these variables over the course of their shift. Before instrumentation was added to aid the operator, specific gravity was measured by weighing a given volume of pulp at intervals of from 30 to 60 min. Scale readings were made at the beginning and end of each shift. No records were kept of operating conditions, such as rpm of the separatory ves-sel, media level in the machine, tons per hour of the products, and so forth. These items were recorded only when spot checks were made by the metallurgical staff. CONTlNlJOUS DENSITY RECORDING The first process instrument used, other than the usual ammeter on the drive motor of the separatory vessel, was a nuclear density gauge and its associated circular chart recorder. These instruments were used to indicate and record specific gravity of the circulating media. This was a tremendous aid to the operator in that tie was able to observe and correct the specific gravity at any time. There was also added incentive to make frequent corrections because of the permanent record made by the recorder of the densities. The addition of the nuclear density gauge was influential in securing optimum quality and recovery of the heavy media product. Manual control was improved, and it became possible for a good operator to main control within f.05 specific gravity units. This compares with an unknown quantity, estimated at f0.15 gravity units, when manual measurement and control was used. An example of the improvement in manual control over the course of one season's operations is shown in Fig. 2. Chart A is typical of the records made shortly after the gauge was installed. Needless to say, it was difficult for operators and foremen alike

Jan 1, 1962

By H. Habenicht, J. J. Scott

An experimental method is described to compare strain data for rock and rock bolts when exposed to shock waves released by blastings. Static and dynamic strains were measured. Bolt gage response indicated a static decay of the bolt anchorage coupled with a reaction due to blasting vibrations. A distinct loss of bolt tension was indicated during vibrations and this was accompanied by a smaller but steady loss of tension due to static loading. The strain losses were found to relate to the shock source distance and the vibrational amplitude in the rock and bolts. Millions of roof bolts are used each year to stabilize mine openings and prevent their failure. Frequently, bolts become loose and lose their effectiveness as reinforcement to the mine structure. Many attempts have been made to determine the cause of loosening, including observation of the bolt tension or bolt torque through the use of torque wrenches, compression pads, and load cells. Pull tests have been used extensively to determine anchorage characteristics.102 These investigations have shown that even when bolts are loaded below the nominal anchorage capacity of the rock under 'static' conditions they exhibit a decay of load through adjustments and slippage at the bolt anchor. Since bolts are quite often found with the plate hanging loose from the rock surface, this condition suggests that some additional mechanism may have played a part in loosening the anchorage. Vibration from blasting or shock loading have been suggested as one cause in this type of anchorage deterioration. This paper gives the results of an investigation carried on at the University of Missouri at Rolla to determine the influence of shock waves on rock-bolt anchorage stability. ROCK BOLT ANCHORAGE UNDER DYNAMIC LOADING CONDITIONS In this report dynamic loading conditions are defined as conditions under which rock and bolts are exposed to vibrations occurring as a consequence of blasting, machine vibrations, earthquakes, rock bursts, etc. Whatever the location of the shock source, the waves created suffer extensive alterations along their travel paths, depending upon the vibrational properties and geometric parameters of the transmitting media. Together with reflection, refraction and diffraction at material boundaries, waves suffer changes in their nature to form tensile, compressive and shear waves. They become polarized, retracted, accelerated, dispersed, so that the waves incident at a point in the material can be the result of either one or a combination of this wide range of processes. A certain fraction of the wave energy will be lost due to friction, deformation, and material failure at the anchor-rock contact. Thus, the physical nature of wave propagation is such that it inhibits an exact analytical solution. For this reason this investigation should be considered qualitative rather than quantitative even though numerical data have been used as a base. CONCEPT OF THE INVESTIGATION Experiments were designed to find, from a series of rock bolts installed in natural mine rock, whether or not, and to what extent, bolt tensions would be influenced when bolts were exposed repeatedly to shock waves such as those produced by blasting. Electronic instrumentation available in the rock mechanics laboratory of the University of Missouri at Rolla was used to observe wave development in the rock and vibrational reactions in the bolts. EXPERIMENTAL PROCEDURE Fig. 1 illustrates schematically the experimental equipment. Electric resistance wire strain gages were used as sensors for the strain response of the rock and the bolts. Bolts were 5 ft long and 5/8 in. in diam, equipped with two-leaf type expansion shells for 1 3/8 in. boreholes. The bolt gages were mounted by use of Du Pont Household Cement, covered with an epoxy insulation and then enclosed in a copper foil for electronic shielding. For details of placement and the wiring diagram see Fig. 2 and 3. The output of both the rock gages and the bolt gages was fed into cathode ray oscilloscopes from which the vibrational traces could be photographed. A static strain indicator was also used to read the output of all gages.

Jan 1, 1968

By F. W. Jessen, R. W. Durie

The dissolution of salt in the development of salt cavities is controlled by free-convection boundary layer flow along the salt surfaces. It is the purpose of this paper to expand upon results published previously, and primarily to illustrate the influence of surface features on the boundary layer and hence the dissolution process in the development of underground salt cavities. General dissolution equations are presented that apply to a surface inclined to the vertical. A salt surface inclined so as to be overlain by water is dissolved by boundary layer flow, while an inverted surface is dissolved by a combination of boundary layer and cellular flow. Detailed investigation of the boundary layer was limited to laminar free-convection flow. Truly laminar free-convection boundary layer flow may be encountered only in laboratory solution cavities, but the boundary layer will control dissolution even where cavity dimensions are such that free-convection turbulence will occur. The factors found to significantly affect the laminar boundary layer will affect dissolution with a turbulent boundary layer. INTRODUCTION Underground salt cavities have been used extensively for the storage of LPG products, and the use of these cavities is expanding each year. The increasing requirements for such cavities suggest the need for a better understanding of the mechanisms involved, for the purpose of the control of cavity geometry and the most effective use of the injected water. A previous paper outlined a quantitative approach to the determination of salt dissolution rates in the laminar free-convection dissolution of salt. It is the purpose of this paper to expand upon the results previously published and to point out significant factors in the application of these results to the dissolution of field cavities. The dissolution of salt in laboratory scale cavities is controlled by the free-convection boundary layer, which is the region of flow along the salt surface caused by the difference in buoyancy forces resulting from the salt dissolution. The transfer of salt into solution at the salt face causes an increase in salinity, and hence a greater density, in the water at the salt surface. The region of higher density tends to fall through the lighter, less saline water and a flowing boundary layer is the result. The water remains stationary at the contact with the salt surface,l so the resulting velocity profile is such that the influence of gravity is opposed by a viscous shear force at the salt surface. For salt to be transferred into solution from a solid surface to a boundary layer of fluid, it must diffuse through a stationary film of water at the salt contact. According to Fick's first law, the rate of mass transfer by diffusion is the product of the diffusion coefficient and the concentration gradient, with diffusion transfer in the direction of decreasing salinity. Once the salt has passed into the boundary layer, it will be transferred by a combination of molecular diffusion and convection. The convection transfer will in turn affect the rate of dissolution by influencing the gradient of the salt concentration at the surface. In the previous investigation by the authors to determine the basic mechanism of the salt dissolution process, an equation was developed that agreed very well with the experimental rates of free-convection salt dissolution from a smooth vertical surface. The technique was taken from the work of Eckert2 in the analogous heat transfer system and will be referred to as the integral method. The rate of salt transfer from a vertical section of height H was found to be:

Jan 1, 1965

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By G. K. Dumbauld, B. E. Morgan

Kesults of laboratory investigations of the effects of drilling muds on oil well cements are presented which show that relatively large quantities of untreated muds do not seriously interfere with the setting of cement slurries, but that relalively small quantities of treated muds seriously retard the setting of cement slurries. Laboratory results also indicate that the harmful effects of contamination with treated muds can he counteracted by the addition of activated charcoal to cements. Also described is the successful use of cement containing activated charcoal for the placement of plugs in oPel hole after previous attempts with ordinary cement had been unsuccessful. INTRODUCTION The contamination of cement slurry by dilution with drilling mud has long been considered a cause of failure in oil well cementing. The cement slurry must displace the drilling mud from the annulus between the casing and the walls of the borehole. and it is probable that some mixing of the slurry and the mud occurs even under the most nearly ideal displacement conditions. Hole enlargement, failure to center the casing in the hole, and formation of gel structure in the drilling mud increase the probability of contamination. In some cementing operations, such as the placement of a cement plug in open hole, considerable mixing of the mud and slurry is likely. Many cement failures which can be attributed logically to no cause other than contamination of the cement slurry by the mud attest the need of a better understanding of this problem. Considerable attention was given to the problem of mud contamination of cements about 20 years ago.The effects of field mud upon cement slurries prepared with different amounts of mix water were investigated thoroughly, and the data obtained were invaluable in determining the causes of the high percentage of failure in oil-well cementing at that time and in bringing about improved cementing results. Since then, many aspects of the problem have changed, due primarily to advancements in cement and drilling mud technology. Today, several types of portland cement are used in well cementing and numerous chemical additives are used in drilling muds. An excellent report on the effects of drilling mud additives on oil-well cements was issued during 1951 by the American Petroleum Institute. Data in the report revealed that many mud additives, notably organic materials in relatively small amounts, produce a marked effect on the properties of cements. Prior to this time, little information has been available on the effects of chemicals commonly used in the treatment of drilling muds upon the properties of cements. Another aspect of the problem of mud contamination of cements, which has received no attention heretofore, is the possibility of producing a cement having properties unaffected by a reasonable amount of mud contamination. In view of the need for additional information on the contamination of present-day cements by currently-used drilling Muds, the investigation described herein was initiated Several years ago with a two-fold purpose: first, to determine the capacity of cement slurries to tolerate contamination by both untreated and treated muds without loss of ability to set and develop strength within a reasonable time; and, second, to investigate the possibility of enhancing the ability of cement slurries to withstand mud contamination by incorporating additives in the cement. The data for this study were obtained by mixing drilling mud with cement slurry and testing the resulting slurry-mud mixture for rate of set and development of strength. Also, several materials were tested for their possible improvement of the property of cement slurry to withstand mud contamination; these materials were tested in both contaminated and uncontaminated cement slurries.

Jan 1, 1952

By H. D. Yoo, M. R. Tek, D. L. Katz

The behavior of gas-storage reservoirs subject to water drive is investigated through analog simulation on an electronic differential analyzer. The simulation technique developed on an LM-10 computer permits the prediction of reservoir volume or pressure resulting from the movement of water in the surrounding aquifer. The method developed on the analog computer consists of setting up an appropriate transfer-function circuit and feeding the arbitrary time-varying boundary conditions as an input signal. The input may be specified as gas reservoir pressure, pore volume or the water flux. Several cases studied include an isolated gas reservoir on a limited aquifer, interference among three reservoirs adjacent to a common aquifer and the growth of gas-storage volume on an aquifer. It is concluded that the method developed on an electronic differential analyzer provides an excellent technique to simulate and investigate the behavior of gas reservoirs subject to water drive. The agreement between the reservoir performance as predicted from the simulation technique and as measured from actual field data is found to be better than the range usually encountered in predicting water-drive behavior. INTRODUCTION It is generally known that some gas-storage reservoirs are located on top of blanket sands of large extent, saturated with brine called aquifers. Because the volume of the body of water associated with aquifers is usually very large and water is compressible, the cyclic pressure variations encountered in normal storage service inevitably cause unsteady, compressible flow conditions in the adjacent aquifers. The solution to radial diffusivity equation for a limited aquifer for constant terminal conditions has been know111 since the early 1930's. The solution for the constant terminal conditions for an infinite aquifer was puhlished in 1949.2 The proldem of handling the unsteady flow of water through a porous medium with time-varying boundary conditions has been studied by many investigators through the use of graphical,3 digital4 computing techniques or on an R-C type of electrical analog called a reservoir analyzer.5 The digital computer performs a series of arithmetic calculations to superimpose the solutions of constant terminal conditions, while the R-C type of analyzer permits the simulation of the continuous medium by means of "lumped-cell" electrical resistance and capacitance elements based on finite-difference approximations. The graphical method is based on the convolution integral solution of the partial differential equalion. The purpose of the present study was to simulate the behavior of an aquifer on a general-purpose, electronic differential analyzer to obtain the influx of water or the change in pressure at the reservoir continuous1r and quickly. The use of the electronic differential analyzer was based on well known solutions for the constant terminal conditions already available in the literature.2,6-8 THEORETICAL DEVELOPMENT MODEL. The gas reservoir (R) is described in relation to an aquifer in Fig. 1. The permeability and porosity of an aquifer sand, the viscosity of the brine, and the compressibility of the brine and the formation are assumed to be constant. It further is assumed that the blanket sand is not thick enough to give appreciable vertical pressure distribution. The model in consideration is circular with radial geometry. The aquifer radius can be of limited or infinite extent. The gas-water interface is assumed to be fully segregated, and the displacement of the gas by

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven't been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,' Barrett,' Dunn,3 and Richards' give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum' or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,'" aluminum,' or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.' Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", '" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By W. B. Gogarty

With flow of non-Newtonian fluids in porous media, effective viscosities are needed for use in the Darcy equation. These viscosities depend on the rock parameters and flowing conditions. In this investigation, rheological and flow results were correlated to develop an expression for calculating effective viscosities. Surfactant-stabilized dispersions of water in hydrocarbon were used with consolidated sandstone cores of different permeabilities. The average shear rate in a core was related to the permeability and porosity of the core and the frontal velocity through the core. By using the correlation obtained for determining effective viscosity, experimental and theoretical values were compared for each fluid system by determining average and maximum errors. For the fluid system showing the largest average error, the correlation fit 38 experimental points with an average and maximum percentage error of 4.3 and 14.8, respectively. For the fluid system showing the least error, average and maximum percentage errors of 1.8 and 4.3, respectively, were calculated using 29 experimental points. INTRODUCTION Use of non-Newtonian fluids in the petroleum industry is not new. Fluids of this type have been used for many years as fracturing agents and drilling muds. Recently, attention has focused on the use of high molecular weight polymer solutions for secondary recovery. Results have been reported on studies relating to the flow behavior of polymer solutions in porous media.1-4 Each study gives the viscosity in the Darcy equation as a function of the rheological properties of the fluid, the characteristics of the porous medium and the pressure gradient. The functional forms of the reported expressions differ somewhat in each study. The first three studies used unconsolidated porous media while the fourth used a single consolidated core. Because of the limited information available on the flow of non-Newtonian fluids in porous media, further investigation was undertaken in this area. We selected non-Newtonian fluids that did not contain high molecular weight polymers in order to minimize core plugging. The over-all objective was to gain a better understanding of the flow behavior of non-Newtonian fluids in consolidated porous media. Specifically, our goal was to determine the relationship between the average shear rate in a core and the frontal velocity. Because of this goal, it was necessary to determine the effect of permeability on the shear rate-frontal velocity relationship. We wanted to replace the viscosity in the Darcy equation with an expression relating to the average shear rate in the core and the rheological properties of the non-Newtonian fluid. THEORY For a time-independent, non-Newtonian fluid, the apparent viscosity is a function of the shear rate. This relationship is given by µ = F(v')...........(1) With Eq. 1, a single value of shear rate determines the apparent viscosity at that shear rate. With flow in porous media, a spectrum of shear rates occurs at any average throughput. An average shear rate v' can be used to represent the spectrum of shear rates that exists within the core. By using v' and the rheological data given by Eq. 1, an effective viscosity is determined for the flowing fluid. If v' is the correct average, µe becomes the appropriate viscosity for use in the Darcy equation. Under these conditions, flow rate-pressure drop relationships can be determined for non-Newtonian fluids. HOW the correct average shear rate might be related to the frontal velocity through the core and the characteristics of the porous media will now be considered. Later, the experimental data are presented that indicate the validity of these

By Arthur Hockman, Howard W. Jaffe, Howard F. Carl

THE problem of establishing practical techniques for evaluating natural corundum ores arose from the desire to improve the existing purchase specifications for crystal corundum procured by the Federal Government for stockpiling. Such purchase specifications had been developed for a large number of products, including minerals and ores considered to be critical and strategic because of the country's dependence on foreign sources of supply. It will be apparent to anyone considering the subject of purchase specifications that the determination of whether or not a submittal meets the specifications is a prime consideration. Consequently satisfactory specifications for minerals should not only incorporate physical, chemical, and mineralogical requirements that are practical but should also establish the means by which both buyer and seller can be assured that materials meet stated requirements. The Munition Board's Material Purchase Specification for corundum, dated February 1954, covered two grades of crystal corundum intended primarily for abrasive use. It established limits of size and of composition: Grade A, at least 95 pct +3 mesh and 92 pct alumina (Al2O3); Grade B, at least 95 pct +7 mesh and 90 pct alumina. It also specified that "of each lot of material, not less than 95 percent shall have a hardness equal to or exceeding nine (9) on Moh's Scale." These specifications were unsatisfactory for several reasons. They did not allow the purchase of lower grades of corundum being used by industry. Neither did they specify exactly what a corundum ore actually was, except that it should contain so much alumina and have a certain scratch hardness. Nothing was said about the abrasive qualities of the material that was to be purchased primarily for abrasive use. During the period 1946 to 1948 supplies of the two grades defined in the then current specifications continued to decrease. Early in 1949 industry recommended that the finer sizes of corundum known as "crystal corundum concentrates," ¼-in. to 16-mesh material, be added to the stockpile specifications and that lower grades of crystal corundum also be included. In the spring of 1949 the National Bureau of Standards and the Bureau of Mines were asked by the Munitions Board to cooperate in developing more practical specifications for grading natural corundum ores. The National Bureau of Standards indicated that it would investigate physical test methods for determining abrasive characteristics of corundum, and the Eastern Experiment Station of the Bureau of Mines at College Park, Md., stated that it would consider the mineralogical aspects of the problem. Members of these two agencies, in consultation with representatives of the Office of Materials Resources of the Munitions Board and of the Federal Supply Service of the General Services Administration, and with the cooperation of industrial suppliers and consumers of abrasive corundum, developed, in a fairly short time, more practical specifications for six grades of corundum ores. The new specifications, issued January 1951, were for corundum, natural crystals, as by this time high-purity synthetic corundum was available and widely used. Nevertheless, for certain specific applications the natural product was preferred over the synthetic material. It has been extensively used in forming snagging wheels. It breaks into more or less cubical particles, whereas artificial corundum fractures into splintery shapes. These produce irregular cuts in glass, while the more symmetrical shape produces a more uniform ground surface. For this reason natural corundum has been preferred for certain types of lens grinding. Pure corundum is clear, colorless alpha alumina (A12O3), but it is rarely found in nature in this form. The most important gem varieties include the blue and yellow sapphires and the ruby. Minute impurities of titanic oxide impart a blue color,

Jan 1, 1955

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

By F. W. Jessen, R. W. Durie

The development in the laboratory of mall salt cavities illustrated that the rate at which salt dissolved was affected by the rate at which fresh water was injected into the cavity. Experiments carried out with small salt cores indicated, however, that the rate of salt removal with forced convection was not significantly different from that with natural convection, provided the flow was in the laminar range. The rate of salt removal was apparently controlled by the water salinity, which was indirectly determined by the rate at which fresh water was injected. With turbulent flow at the salt surface, the rate of salt removal could be increased several-fold with the same salinity in the cavity. A quantitative evaluation of the rate of salt removal under natural convection was attempted by using techniques developed for the analogous heat convection system. The values of the rate of salt removal obtained experimentally were considerably greater than the calculated values due to surface irregularities. To determine the effect of these irregularities, the rate of salt removal was found for a smooth surface by experimentally determining the rate of salt removal as an irregular surface developed and then extrapolating this trend back to initial time. Excellent agreement between the experimental and calculated values then were obtained. INTRODUCTION Underground cavities leached from massive salt formations have been used extensively for many years for storing LPG products. The development techniques for storing methane gases in the liquid state at a low temperature leads to speculation that underground salt cavities of controlled geometry may be quite important in this field. In any case, the increasing number of salt cavities used for storage indicates an impending need for a better knowledge of the washing process to efficiently develop maximum storage volumes within specified regions. It is the purpose of this paper to discuss some aspects of -the mechanism of the dissolution of salt in the formation of cavities of controlled geometry. Although no attempt is made to resolve the problems that may be associated with the storage of methane in the liquid state in salt formations, the fact that salt cavities can be formed at reasonable cost would appear to justify investigation in this direction. Further, underground cavities have the advantage of allowing storage at higher pressures (and hence higher temperatures) than surface installations. Although the thermal conductivity of salt is somewhat higher than frozen earths, 0.017 cal/(sec) (cm)(c) for salt at 32F vs 0.005 cal/(sec) (cm) () for ice at this temperature, this disadvantage is offset by the higher storage temperature in underground cavities. For example, at atmospheric pressure, the temperature of liquid methane would be —258F. In a storage cavity at 2,000 ft, the pressure would be approximately 1,000 psia, which would allow a storage temperature of -9OF. The formation temperature would be roughly 110F at this depth, hence the total temperature differential would be 200F. Under surface storage conditions the corresponding temperature difference would be some 333 F (75 F + 258 F). The results of this difference can be compared more readily by substituting the appropriate values of thermal conductivity, temperature difference, heat capacity and density into the solution of the diffusion equation for the unsteady linear conduction of heat. For the underground salt storage, the heat flux is 15cal/(sec) (sq cm), where t is the time in seconds from the initiation of the cooling. For the surface system, and using the thermal properties of ice at the average temperature, the corresponding figure is 21cal/(sec) (sq cm). Hence, the heat losses through ice under surface conditions would be some 30 per cent higher than the underground salt storage. This ratio would vary, considerablv. Of course, for other conditions, but it indicates that an advantage over surface facilities may be obtained by storage in underground salt cavities.

Jan 1, 1965