Search Documents

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 1, 1919

Two 6.17-m-diam (20.25-ft) shafts, said to be the largest ever opened with mechanical raise boring techniques, were completed in May and June 1978, at Monterey Coal Co.'s No. 1 mine near Carlinville, Ill. According to the shaft contractor for the project, Frontier-Kemper Constructors, the openings are 60% greater in cross section than the largest previous raise-bored shaft, which had a diameter of 4.85 m (16 ft). Both vertical shafts are 93 m (305 ft) in total depth, with the upper 28-30 m (90-100 ft) sunk and lined by conventional methods through unconsolidated overburden and the remainder mechanically bored through sedimentary rock. The two shafts will be used for service access as well as to augment ventilation.

Jan 12, 1978

By W. E. Hess

At the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed.

Jan 2, 1955

By A. W. Hale

In a work published in 1838, De Morgan, the author of the article on " Probabilities," in the Encyclopedia Metropolltimn, says: " The method of least squares is not yet introduced intb the affairs of common life,.....that many things which are denlonstrable only by the higher branches of mathematics are looked upon as useless." And he mentions an instance in which "a method was suggested for estimating the relative importance of boroughs, by considering their population and ~wntributions to the revenue con)-

Jan 1, 1881

By R. M. Board

This paper will focus on measurement and control of four main aspects of crushing, namely horsepower, bowl level, mantle position and feed rate, and will discuss related sensors and control techniques, some of them designed specifically for crusher control, that have proven successful and reliable in many installations.

Jan 1, 1982

By Richard H. Ross

A broad definition of' "Mill Design" might cover everything from the first tentative choice of general process to the final structural details for construction. The first phases are mainly concerned with metallurgy and economics and the final stages with the mechanics of putting the selected equipment together into an integrated plant. It is the purpose of this article to discuss only data, derived from laboratory testing, that contributes directly to design of the milling plant itself, and only the plant design phases that are influenced by laboratory testing. Most ore beneficiation testing is devoted to determining recoveries, grades of products, elimination of impurities, reagent and supply requirements, etc. having little to do with physical plant design although these factors are of prime importance in the evaluation of a mining project.

Jan 3, 1964

By T. J. DeMull

More than 1.81 mt (2 million tons) of low grade ore have been heap leached at the Alligator Ridge mine. Since inception of leaching in 1980, several modifications have been made to ore agglomeration, heap construction, and leach operation practice. These modifications have improved the percolation rate of the ore and the rate of gold extraction from the ore. Changes made in each of these areas are described and the effects of the changes are discussed.

Jan 1, 1984

By A. Sainato, E. Baker, J. Cervik

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the US is limited to a few plow operations in the deeper parts of the Pocahontas No. 3 Coalbed. The technology for infusing water into retreating longwalls is described and results of a recent Bureau test in the Lower Sunnyside Coalbed demonstrated dust reductions ranging from 47% to 64%. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 2.5 m/s (500 fpm) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23% reduction in operating costs when coal production is increased by changing from unidirectional to bidirectional mining with water infusion.

Jan 1, 1986

By J. Menashi, D. A. Douglas, A. S. Rappas

A process has been developed for recovering the refractory metals chromium (Cr), vanadium (V), molybdenum (Mo), and tungsten (W) in mixed secondary source materials, such as contaminated grinding wastes. The wastes are calcined with sodium carbonate in air to yield water-insoluble oxides of the base metals iron (Fe), nickel (Ni), cobalt (Co), and copper (Cu) and water-soluble salts of the refractory metals. An aqueous leach separates these two classes of metal values. Cobalt, nickel, and copper can be recovered from the oxidic residue by conventional processing methods. The leach solution is purified and then treated to recover the refractory metals. The process can accommodate a wide range of feed compositions and generates a minimum of aqueous effluents.

Jan 1, 1985

By C. A. Crawford

NICKEL and the nickel-copper alloy, the latter generally referred to as monel metal, are available in a variety of wrought and fabricated forms, of which the following are regular commercial products: [ ]

Jan 1, 1928

By D. E. Pickett, E. G. Joe

In accordance with good industrial practice, Canadian metallic-ore concentration plants have always recycled a high proportion of process water to save reagents, save power, conserve water resources, and to protect the community water supplies, to give only a few reasons. In the last few years there has been awakened public concern for the environment and, consequently, government regulations have been added as additional reasons. Present recycling practices are summarized as a basis for improved plant design and operating procedures and for further research. In addition, an attempt is made to determine why plants do not recycle water in certain situations. Although not all Canadian mills are covered, the many examples given indicate the problems and the effort being made to solve them. Wherever available, the chemical quality of the water and the process requirements are indicated as well as the other parameters affecting water recycling at each operation.

Jan 1, 1975

By A. Bruce Matthews

Of the many opportunities in the mining industry to invest funds to improve operations, there is always some limit in every company as to how much can be spent each year for the acquisition of capital assets. Generally, there are many more opportunities for investment than funds to make the investments. As such, one of management's goals is to select the most profitable of all the opportunities available. Each opportunity must be carefully analyzed for its potential percentage rate of return. This percentage return or return on investment concept is an accepted financial yardstick of business profit- ability. For today's mining engineers, this problem resolves itself in the job of determining how to in- vest most productively the cash that is flowing from their operations so that it will multiply in value. There are four basic types of capital investments: Strategic investments, such as selecting a plant site, are those that affect virtually all long-run plans of a company. Change in a company's product line and expansion of company facilities are two other types of capital investments.

Jan 3, 1963

By B. Das, V. Hucka

In light of the present energy crisis, coal appears now as the only reliable source of energy. The production of coal is expected to regain a rising trend after the latest slump. Aside from the competitive price with natural gas and oil, the other retarder of coal production is its environmental pollution effect. Gasification of coal has been advanced as the partial solution to the energy-ecology crisis. All the Advantages In situ gasification of coal may be considered a further step in this direction. It carries all the advantages of normal coal gasification as a stable source of energy; it is clean to handle and nonpolluting of the environment. It partially and sometimes fully does away with mining, makes uneconomical low grade coal and lignites economical and places some formerly unworkable seams within the scope of modern technology. The seams posing problems for mining due to tectonic disturbances may be converted into gas in situ. Low grade coals, such as lignites, which otherwise would be left in nature as uneconomic wealth, may be exploited by underground or in situ gasification. Thus, in situ gasification is likely to increase the exploitable reserves of coal and may reduce the cost of production. An additional merit of this method is that coal substance never reaches the surface and there is no problem of cinder disposal.

Jan 8, 1973

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Milling or Smelting. Graduate Missouri School of Mines desires position in milling or smelting department of responsible non-ferrous mining company. Twenty-eight years of age, married, 4 1/2 years in milling, smelting, and experimental work with large copper company. Refererences. A-3326. Technical Graduate, B. S., E. M., 1909, age 34, single, desires position with prospects of advancement. General engineering experience in, mining, development and exploration work, estimating, mining methods, mapping, mine accounting, and drafting. Can furnish complete .record of experience. A-3327. Superintendent or Engineer. Civil engineer, technical graduate, age 29, seven years varied experience, municipal, drainage, mining of iron ores in Virginia, desires position as superintendent or engineer; available immediately; references. Salary expected $2000 to $3000. A-3131. Engineer or Executive. Graduate mining engineer, age 31, married, eight years' experience in mine operation, exploration and reporting, desires engineering or executive position of responsibility. Now employed. Highest credentials. A-3422. Mine Manager or Superintendent, technical, education, married, desires opening. First class references. Wide experience in mine development and operation; milling and general construction as executive. A-3496.

Jan 8, 1919

By S. C. Termes, P. E. Richardson, R. L. Wilfong

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble cross-linked starch xanthate (ISX). ISX is insoluble, has a shelf life of more than a year when kept cold, and has a higher molecular weight due to cross-linking than the soluble, non-cross-linked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines, but no silicious gangue. Floc formation, floc size, and settling rate are dependent on pH. The pH dependence, however, differs for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1984

By J. Th. G. Overbeek, R. Schumann, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.1-3 Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles.

Jan 5, 1954

By Henry Engelmann

ORes are generally found in the mines mixed with more or less base matter, which renders their treatment by smelting or milling unnecessarily costly. They have to be sorted. Those of a higher grade remain often mixed with substances which might, with hardly a loss of metal and at small expense, be removed by dressing machinery, and a concentrated and purified ore thus obtained, which would bring a far higher price, because it can be reduced by cheaper methods, and, at any rate, at less expense, besides affording a saving of transportation, which in our territories is often an item of no small magnitude. The ores of a lower grade have often to be

By John Cogan, P. M. Gomez

A typical problem in applied rock mechanics is an accurate prediction of support requirements for deep rock cuts. This paper presents experience with this problem as obtained from excavations for a powerhouse at the Pine Flat Dam near Fresno, California. The project, sponsored by the Kings River Conservation District is still under construction. Highly jointed and weathered rock was discovered during initial excavation. Wedge failures along clay filled joints and bedding planes presented potential support problems. Detailed mapping of joints and beds was undertaken to establish basic patterns of all rock discontinuities including mean orientations and an estimate of orientation variations. Rock bolting patterns were devised to meet these patterns as excavation proceeded. Shear friction angles across joints and beds were estimated from rock wedge fallouts. Friction angles as low as 27º were identified on highly weathered joints. Weathering strongly influenced stability conditions. Examples of bolting patterns to stabilize critical slopes are presented.

Jan 1, 1982

The International Mining Convention held in Nelson, B; C., May 17 , to 19, was attended by nearly 500 delegates, of whom about 100 were from Spokane, 150 from the Slocan district, and the others from different points in Canada and the United States. Arrangements were in charge of the Nelson, Slocan and Eastern British Columbia Mining Men's Club, under the direction of Secretary Fred A. Starkey, assisted by the City of Nelson, Associated Boards of Trade of Eastern British Columbia and Nelson Board of Trade. The Columbia Section of the American Institute of Mining Engineers; cooperating with the Western Branch of the Canadian Mining Institute, provided the technical program, under the management of Secretary E. Jacobs, of Victoria, and Secretary L. K. Armstrong, of Spokane. Three technical sessions were held, at which the following were read: Difficulties of the Electrolytic Zinc Process, by Thomas French. Sketch of the Geology and Ore Deposits of Nelson and Kootenay Region, by Arthur Lake's. Advantages of Local Organization of National Societies, by W. H. Linney. Review of Kootenay Mining, by Bruce White. Milling of Partially Oxidized Ores, by S. S. Fowler.

Jan 7, 1917

By Bernard Amadei, Richard E. Goodman

A medium is anisotropic if its properties vary with direction. This is the general characteristic of many rocks, for example, schists, slates, gneisses, phyllites and other metamorphic rocks. Bedded and regularly jointed rocks also display anisotropic behavior. This paper is concerned with the influence of rock anisotropy on in-situ stress measurements. It is limited to stress measurements by overcoring techniques for which strains and displacements are recorded either on the walls of a pilot hole at the end of one or several boreholes or within instrumented solid or hollow inclusions perfectly bonded to the surface of the pilot hole. The rock is described as homogeneous, continuous, anisotropic and linearly elastic. The following questions are answered with special emphasis on rocks that can be classed as transversely isotropic or orthotropic: the number of independent measurements obtainable in a single borehole; the number of boreholes required to determine the in-situ stress field; the influence of rock anisotropy on these numbers; the influence of the anisotropy type and the error involved by neglecting rock anisotropy.

Jan 1, 1982