Search Documents

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

Jan 1, 1942

Edward Dyer Peters, the only child of Henry Hunter Peters and Susan Barker Thaxter, was born in Dorchester, Mass., June 1, 1849. From his father he was a descendant of the Peters family of Ipswich and Andover, Mass., whose earliest ancestor settled in Essex County in 1659; while upon his mother's side he descended from several old Hingham families, as well as from the Quineys and from Governor Bradford. Between the ages of fourteen and sixteen he was a student at the Episcopal School for boys in Cheshire, Conn. Near the school was an old tin mine, and he used to spend his Saturday afternoons exploring it. When Edward was sixteen, his father sold his property in South-borough, and for the next three years lived in Europe. Sept. 26, 1865, Edward entered the Royal School of Mines at Freiberg, Saxony. In the summer of 1867 he joined his family on Lake Geneva, and spent a part of the season in that vicinity, going to Chamounix and taking other trips. Extract from a letter to his father: Elbingerode, Harz, Aug. 30, 1868: I left Freiberg with my friend Lilienthal, on Wednesday the 19th of August, reached Leipzig in the evening and spent the night in that city: the next morning we took the cars and in the afternoon reached Eisleben, in Prussia, which was to be our first stopping-place; there are immense copper-mines and smelting-works at this place, and the method of working the mines is very peculiar ... The next morning we got up at five and spent the whole day in the smelting-works where I obtained a number of drawings of the furnaces they use here and a good many valuable data. Saturday morning we got up at four o'clock, and descended a mine about three miles from the town; the Director of this mine was one of the most intelligent and agreeable men that I ever met; he accompanied us in the mine and explained everything that was new to us. The system of mining at Eisleben is peculiar to this town, and is not used at any other place in the world; the copper ore comes in narrow, flat veins eighteen inches high, at the utmost, consequently the men work lying flat on their left side and using the pick with both hands: the ore is carried out of the side passages into the main ones, in very low waggons about twelve inches high, and four by two feet; the boys who pull these waggons have a board buckled to their left thigh and their left arm; they pass their bare foot through a strap in the waggon and wriggle along on their side dragging the waggon after them, with their foot, almost as fast as a man can walk above ground. In the afternoon we walked over to Hittstadt, about twelve miles, and remained there Sunday and Monday. Monday night, at ten o'clock we went out to one of the smelting-works, to see the refining of the copper; this is only done at night, so we worked there from ten in the evening till eleven the next morning, and came home all blackened up and with blistered hands, for our skin was not quite so tough as that of the workmen: at noon the same day we took the stage to Ascherls-leben, and then the train to Stassfurt, where there are immense salt-mines, as well as factories for the manufacture of bromium, which latter process is, however, kept a profound secret, so we had very little hope of seeing anything but the salt mines; we were talking with our landlord about our disappointment, that evening, when he told us that the director of the Bromium works was sitting in the next room with no company but his glass of beer, so we went over to him, introduced ourselves as Americans, and actually succeeded in persuading him that it could do his business no earthly hurt if he showed us his works; at last he consented, after making us give our word of honor

Jan 1, 1919

By Robert B. Sosman

ONE of the most neglected fields for physicochemical education as well as for research is that of high-temperature phenomena. Few universities or technical schools give instruction in the physical chemistry of substances at high temperatures. On the contrary such instruction is almost entirely confined to the region between the freezing and boiling points of water. This field should be extended to a much wider range of temperatures, both low and high. Such an extension is logical, sound, feasible, and practical.

Jan 1, 1943

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.' Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.' Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953

Jan 1, 1925

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By J. F. KENP

THE White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River .branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, free-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limestone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Mar 1, 1907

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

James GayleY, New Pork City (communication to the Secretary*) :—The main thing that is sought after in this matter is that all purcliases shall be made by analysis. This is done already in special lines, as in the manufacture of various grades of steel in which phosphorus, silicon and sulphur are specified within narrow limits, and I quite agree with Mr. Cook that specifications, which are over-rigid in unessential particulars, should be avoided, as they defeat their own purpose because unreasonable requirements permitting no variation are practically not fulfilled, and it is impossible to specify grade

Jan 1, 1905

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By G. Howell Clevenger, Bhupendranath Ray

Formerly great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,l Breuil,2 Wigham,3 Burgess and Aston: Ball and Wingham,5 Miiller; Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil9 and Stead.10 Stead11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence 'of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness" to the presence of small amounts of copper. Turner12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 1, 1914

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period June 10, 1917, to July 10, 1917. Guy N. Bjorge, Boston, Mass. H. H. Lauer, Allentown, Pa. A. H. Burroughs, Jr., Britannia Beach, E. C. Lee, Pittsburgh, Pa. B. C., Canada. Montrose L. Lee, Port-au-Prince, Hayti. Karl Eilers, New York, N. Y. Eugene McAuliffe, Paducah, Ky. H. S. Emlaw, Grand Haven, Mich. R. H..McMillen, Pittsburgh, Pa. W. R. Hamilton, San Francisco, Cal. L. D. Moore, Providence, R. I. Fred N. Hays, Sharon, Pa. Fred J. Pope, New Rochelle, N. Y. E. Hibbert, Nickelton, Ont., Canada. George S. Rice, Washington, D. C. Charles Janin, San Francisco, Cal. W. G. Swart, Duluth, Minn. Milton A. Allen has resigned his position with the Federal Lead Co. and accepted a position with the Arizona State Bureau of Mines, Tucson, Ariz. L. W. Bahney has resigned as Professor at Yale University and accepted a position as metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn.

Jan 8, 1917

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By William G. Pariseau

Advances in numerical methods of analysis and computer technology during the past decade have brought many formerly intractable ground control problems within easy reach of present day graduate mining engineers. However, the new technology brings with it new problems. The identity of these problems are largely those arising from a lack of familiarity with the capabilities and limitations of the new technology. In this regard, the central problem in ground control planning is the calculation of ground motion associated with mining. The fundamentals of this problem leading to a form suitable for computer programming are therefore reviewed. Solution procedures in the broad sense including the gathering of input data and the interpretation of output are described. Computer program capabilities necessary for ground control analysis are discussed and the steps necessary to implement an analysis are outlined.

Jan 1, 1983

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950