Search Documents

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982

By W. R. Hibbard

THE classical work on the electrical conductivity of alloys was carried out by Matthiessen and his coworkers1 in the early 1860's. He attempted to correlate the electrical conductivity of alloys with their constitution diagrams, but the information regarding the latter was too meager for success. Guertler2 reworked Matthiessen's and other conductivity data in 1906 on the basis of volume composition (an application of Le Chatelier's principle with implications as to temperature and pressure effects), and obtained the following relationships between specific conductivity and phase diagrams (plotted as volume compositions) : 1—For two-phase regions, electrical conductivity can be considered as a linear function of volume composition, following the law of mixtures. 2—For solid solutions, except intermetallic compounds, the electrical conductivity is lowered by solute additions first very extensively and later more gradually, such that a minimum occurs in systems with complete solid solubility. This minimum forms from a catenary type of curve. Intermetallic compound formation with variable compound composition results in a maximum conductivity at the stoi-chiometric composition. Landauer" has recently considered the resistivity of binary metallic two-phase mixtures on the basis of randomly distributed spherical-shaped regions of two phases having different conductivities. His derivation predicts deviations from the law of mixtures which fit measurements on alloys of 6 systems out of 13 considered. Volency (Ionic Charge) Perhaps the first comprehensive discussion of the electrical resistivity of dilute solid-solution alloys was presented by Norbury' in 1921. He collected sufficient data to show that the change in resistance caused by 1 atomic pct binary solute additions is periodic* in character. The difference between the period and/or the group of the solvent and solute elements could be correlated with the increase in resistance. Linde5-7 determined the electrical resistivity (p) of solid solutions containing up to about 4 atomic pct of various solutes in copper, silver, and gold at several temperatures. He reported that the extrapolated"" increase in resistance per atomic percent addition is a function of the square of the difference in group number of the solute and solvent as follows: ?p= a + K(N-Ng)2 where a and K are empirical constants and N and Ng are group numbers of the constituents. This empirical relation was subsequently rationalized theoretically by Mott,8 who showed that the scattering of conduction electrons is proportional to the square of the scattering charge at lattice sites. Thus, the change in resistance of dilute alloys is propor-t,ional to the square of the difference between the ionic charge (or valence) of the solvent and solute when other factors are neglected. Mott's difficulty in evaluating the volume of the lattice near each atom site where the valency electrons tend to segre-gate: limited his calculations to proportionality relations. Recently, Robinson and Dorn" reconfirmed this relationship for dilute aluminum solid-solution alloys at 20°C, using an effective charge of 2.5 for aluminum. In terms of valence, Linde's equation becomes ?P= {K2 + K1 (Z8 -Za)2} A where K1 and K2 are coefficients, A is atomic percent solute, Z, is valence of solvent, and Zß, is valence of solute. Plots of these data for copper, silver, gold, and aluminum alloys are shown in Fig. 1. The values of K1 and K2 are constant for a given chemical period (P), but vary from period to period. The value of K, increases irregularly with increasing difference between the period of the solvent and solute element (AP), being zero when AP is zero. The value of K, appears to have no obvious periodic relationship. All factors other than valence that affect resistivity are gathered in these coefficients. Because of the nature of the coefficients, Eq. 1 is of limited use in estimating the effects of solute additions on resistivity unless a large amount of experimental data are already available on the systems involved. It is the purpose of the first part of this report to investigate the factors that may be included in the coefficients of Linde's equation. On this basis, it is hoped that the relative effects of solute additions on resistivity can be better estimated from basic data, leading to a more convenient alloy design procedure. It is well 10,11 that phenomena that decrease the perfection of the periodic field in an atomic lattice, such as the introduction of a solute atom or strain due to deformation, will also increase the electrical resistivity. Thus, in an effort to relate changes in electrical resistivity to alloy composition, it appears appropriate to consider the atomic characteristics related to solution and strain hardening

Jan 1, 1955

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By John C. Sawyer

The mechanism of catastrophic oxidation of chromium and 446 stainless steel is examined. Data are presented to show that accelerated oxidation of these two materials, as caused by lead oxide, can occur in the absence of a liquid layer contrary to presently accepted theory. An alternate theory is proposed in which the rate of accelerated oxidation is a function of the rate at which lead oxide destroys the protective oxide formed on the base metal. An example of the application of the theory is given for the catastrophic oxidation of chromium in the presence of lead oxide. WHEN stainless iron-, nickel-, or cobalt-base alloys are heated in air to moderate temperatures in the presence of certain metallic oxides, oxidation will proceed at an accelerated rate. This phenomenon, often called "catastrophic oxidation", is most pronounced for the stainless steels. With these alloys the condition is so severe that large masses of oxide will form on the surface of the alloy in 1 hr or less at temperatures of 1200o to 1700oF. While a number of oxides are known to cause this effect, PbO, V2O5, and Moo3 are the most familiar, having been the subject of one or more investigations which have appeared in the literature.1-7 In presenting the results of these investigations, many of the authors have offered possible explanations to account for the more rapid rate of oxidation observed; however, the liquid layer theory as proposed by Rathenau and Meijering 2 has been the most commonly accepted mechanism. The liquid layer theory proposes that a low-melting oxide layer is formed on the surface of the alloy as the result of the interaction of the alloy oxide and the contaminating oxide. When the temperature of oxidation is above the melting point of the oxide on the surface, a liquid layer will form and oxidation will proceed at an accelerated rate. At temperatures below the melting point of the surface oxide, oxidation will proceed more slowly in the normal manner. It is argued that the rates of diffusion of oxygen and metal ions through the liquid layer are extremely rapid thereby accounting for the high rate of oxidation. Various experimental data have been presented to show that the temperature at which accelerated oxidation first becomes apparent coincides with the melting point of the eutectic oxide which would be present on the surface. Some exceptions have been observed, e.g., silver will oxidize in the presence of Moo3 at temperatures below the lowest melting eutectic; on the other hand, stainless steel will not be catastrophically oxidized at 1500oF in a molten bath of PbO and SiO2. In reviewing the various theories which have been used to explain catastrophic oxidation, Kubaschewski and Hopkins 8 favor the liquid layer theory, but note that, ".. .as experimental observations are not altogether in agreement with this theory (liquid layer theory), one should consider it a necessary but not a sufficient condition." In contemplating the liquid layer theory, it appears that sufficient evidence has not been presented to establish the theory beyond question. As a means of further clarification, a program of research was undertaken to determine in greater detail the mechanism of accelerated oxidation as caused by lead oxide. The first part of the program deals with a comparison of the oxidation of both AISI 446 stainless steel and chromium metal in the presence of lead oxide, vs the oxidation of these two materials in air alone. These comparisons are made at a number of different temperatures, most of which are below the melting point of the surface oxides. The second part of the program is concerned with a presentation of an alternate theory of accelerated oxidation exemplified by the system Cr-PbO-Air. PROCEDURE AND RESULTS Several experimental methods are commonly used to follow the progress of oxidation. One of these, the weight-gain method, was chosen for this work. This procedure requires that a specimen of the alloy be weighed, oxidized for a given period of time at an elevated temperature, and reweighed—the difference between the two weights being noted. The weight gain of the specimen represents the amount of oxygen acquired from the atmosphere to transform a portion of the specimen to oxide. In those cases where there is a tendency for the specimen or oxide to volatilize at the testing temperature, additional data must be collected so that a correction factor can be determined. This factor must be applied to the weight change in order to ascertain the actual amount of oxidation which has taken place. The specimens used for this work were 1 1/2 in.

Jan 1, 1963

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By D. R. Parrish, K. W. Beaver, H. W. Wood, R. W. Rausch

A pilot test of forward combustion in the Shannon pool, Salt Creek field, Wyo., is described. The Shannon sand, 950-ft deep, contains a heavy (25" API), viscous (76 cp) oil. Natural reservoir energy is limited. Primary production, intermittent since 1889, recovered only about 2 per cent of the oil in place. The field is operated by Pan American Petroleum Corp. for the Midwest Oil Corp., the owner. The original pilot was a 1.32-acre five-spot. The expanded pilot has eight producing wells surrounding a roughly triangular area of about five acres with the injection well near the center. A control or comparison well was also recompleted in another part of the field. Operation of the pilot has been little different front an ordinary gas drive. Little special equipment was found to be absolutely necessary. Except for some use of a temperature-resistant cement, all wells were conventionally completed. In spite of poor oxygen consumption, the over-all performance of the pilot has been good. Total oil recovery to June 1, 1961, was 73,971 bbl. The wells of the original pilot alone had produced about 24,000 bbl, equivalent to 50 per cent of the oil in place, when fire breakthrough at the first well occurred. These wells have now produced oil equivalent to more than 74 per cent of the oil in place in the original pilot area and production is continuing. It appears that ultimate recovery will approach theoretical maximums before the wells must be abandoned. Performance of the pilot has been encouraging, and expansion to a fieldwide combustion operation is being investigated. INTRODUCTION The results of both laboratory investigations and field tests of underground combustion have been reported previously.' However, most of the field tests were primarily experimental. More information and experience are needed before forward-combustion operations can be engineered with confidence. The purpose of this paper is to present the results of a successful pilot test of forward combustion. These re- sults should increase confidence in forward combustion as a practical method for commercial oil recovery. HISTORY OF THE SHANNON POOL The Shannon pool is located on the north end of the Salt Creek field in Natrona County, Wyo. It is approximately 50-miles north of the city of Casper. The Shannon pool's3 discovery well was completed in 1889, making this one of the oldest oil fields in the Rocky Mountain region. Three more wells were drilled in 1890. First production was hauled in wooden barrels by horse and wagon to the railroad in Casper. In 1894 a small refinery, the first in Wyoming, was built in Casper to process the Shannon crude. In the following years the field changed hands several times. It appears that each new owner did some development drilling as several wells were completed in each of the years 1895, 1902, 1905 and 1912, with negligible development in the intervening years. Forty-eight wells were drilled in this period, but many were later abandoned. Discovery of the more prolific Salt Creek field proper ultimately forced suspension of operations at the Shannon pool. After 1915 there was only sporadic production, mostly to supply cheap boiler fuel to drilling rigs in the Salt Creek field. But even this was discontinued in 1931. Since then the pool had been dormant until the recent operations, which are the subject of this paper. The Shannon pool is now owned by the Midwest Oil Corp. Field operations are conducted for Midwest by Pan American Petroleum Corp. THE RESERVOIR Fig. 1 is a map showing subsurface contours of the Shannon pool. The reservoir is on a nose of the Salt Creek anticline dipping to the north at about 500 ft/mile. The trap is provided by a shallow fault on the updip side of the productive area. The downdip limits are bounded by water, but this water has not provided an effective source of reservoir energy. The Shannon sand outcrops at many places in the immediate vicinity, providing good surface indications of the Salt Creek anticline. At the Shannon pool the sand has been lowered by faulting and is overlain by about 900 ft of shale and other sands. The Shannon sand consists of two members. The upper, a water sand, is about 40-ft thick and is separated from the lower member by several feet of sandy shale. The oil pay occurs in the lower mem-

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By A. B. Kinzel

ALTHOUGH vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding con-tribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type-18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted, since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents 'result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less-generally at the usual 0.65 to 0.75 per cent.

Jan 1, 1932

By W. B. Lilienthal, J. C. Melrose

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

By J. R. Schneider

INTRODUCTION Landowners in Texas for many years have freely granted, reserved and leased "oil, gas and other minerals" or interests therein. In recent years we have witnessed much litigation concerning what sub- stances should be included as "other minerals" within the phrase "oil, gas and other minerals," and this question has received the attention of numerous legal scholars. At the South Texas Uranium Seminar held in Corpus Christi, Texas, in September, 1978, Mr. William R. Dodson presented a paper dealing with this very subject and entitled "Uranium - Mineral or Surface? Who Owns It?" In his paper, Mr. Dodson reported on two recent Texas Supreme Court decisions, Acker v. a, 464 S.W.2d 348 (Tex. 1971) and Reed v. Wylie, 554 S.W.2d 169 (Tex. 1977). which held that the particular substance in question in each case is not a mineral within the phrase "oil, gas and other minerals" if substantial quantities of the substance lie so near the surface that production will entail the stripping away and substantial destruction of the surface. Since that time another chapter has been written in the Texas saga of "When is a Mineral not a Mineral?" and it is the intent of this paper to present an update of the Texas law. A review of the early Texas cases so ably covered by Mr. Dodson in his paper will not be repeated, except as is necessary to illustrate the evolution of the legal doc- trine which has been so aptly named "The Surface Destruction Test". BACKGROUND In order to appreciate the genesis of the problem, one must consider that oil and gas production commenced in Texas many years ago, Spindletop came in in 1901. As oil and gas became more valuable, land- owners with considerable frequency sold interest in the oil, gas and mineral estates in their lands, and reserved interest in the oil, gas and mineral estates in their lands when they disposed of their property. Due to the oil and gas background, and perhaps be- cause oil and gas was paramount in the minds of the parties, the traditional language employed in these grants and reservations was "oil, gas and other minerals" or variations thereof. There are literally hundreds of instruments employing this language constituting a link in the chains of title to thous- ands of acres of Texas land. In addition, there are thousands of acres of Texas land held by oil, gas and mineral leases, the primary terms of which have been perpetuated by production, containing similar language in their granting clauses. The severance of the mineral estate from the surface estate results in two separate and distinct estates, each having all of the incidents and attributes of an estate in land. with the surface estate being the serviant estate, and the mineral estate being the dominant estate and having certain easements in the surface estate to explore. produce and remove the minerals. Harris v. Currie. 176 S.W.2d 302, 305 (Tex. 1943). As observed by the court in the Harris case, this is because a grant or reservation of minerals would be wholly worthless if the grantee or reservor co~lld rwt enter upon the land in order to explore for and extract the minerals granted or reserved. Although the Texas law has recognized that an oil and gas lessee has the right to use so much of the surface as is reasonably necessary to produce the minerals. Warren Petroleum Corporation v. Monzingo, 304 S.W.2d 362, 363 (Tex. 1957), recent decisions of the Court have qualified this doctrine. In Getty Oil Company v. Jones. 470 S.W.2d 618 (Tex. 1971). Getty's pumpine, units were interfering with ones self-propelled sprinkler system utilized for irrigating the premises, and Jones sought to require Getty to install the-pumping units in cellars so that the sprinkler system could pass over them. In an effort to accommodate both the surface estate and the mineral estate, the court held (page 622) "...where there is an existing use by the surface owner which would otherwise be precluded or impaired, and where under the established practices in the industry there are alternatives available to the lessee whereby the minerals can be recovered, the rules of reasonable usage of the surface may require the adoption of an alternative by the lessee". Bearing in mind that the "reasonable use doctrine" grew up in the oil and gas industry involving sub- stances which can be produced by methods that do not destroy or deplete the surface estate, the question presented is whether the Texas courts will extend this doctrine to situations where claimants of "other minerals" seek to produce shallow deposits of iron ore, coal, lignite and uranium by surface mining methods which do destroy or deplete the surface estate? The surface destruction test has answered this question in the negative, at least as to iron. coal and lignite. However, the multitude of mineral estates in Texas which have been created by a grant. reservation or lease of "oil, gas and other minerals" will, doubtlessly, continue to fuel the fires of litigation. EARLY TEXAS DECISIONS In view of the evolution of the Surface Destruc- tion Test, an exhaustive review of the early Texas

Jan 1, 1980

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel'kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)' issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By J. C. Melrose, W. B. Lilienthal

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

By Frederick J. McGarry, Fred Moavenzadeh

An experimental investigation of the thermal and mechanical responses of rock materials to laser radiation is described. Specifically, the following three topics have been studied in detail: 1. Temperature measurements on thin discs subjected to laser radiation. 2. Strain measurements on thin discs subjected to laser radiation. 3. Observation and evaluation of cracking and spalling phenomena in constrained and unconstrained thin discs respectively, subjected to laser radiation. In conjunction with the experimental work done, use was made of a heat flow analysis and a stress analysis program developed for this purpose. It was possible to theoretically predict the thermal and mechanical responses of a rock specimen to laser radiation and then compare them with experimental observations. Good correlations were obtained.

Jan 1, 1971

By Malcolm McColl, C. A. Mead

Thin films (of mica have unique attributes that are exceptionally good for studies of high-field conduction mechamisms in thin-film insulators and the quantum mechanical tunneling of electrons from metal to metal. The principal advantages of using mica films are that the films are crystalline and the cleavage planes occur every 10Å. This property results in films whose thicknesses are integral multiples of 10Å and whose surfaces are uniformly parallel over sizable areas. Hence, very well-defined metal -mica-metal structures are possible. Furthermore, the fact that the insulator is split fro??! a bulk sample allows the index of refraction, dielectric constant, forbidden energy gap, and trapping levels and their density- to be obtained directly from measurements performed on thick samples Of mica rather than requiring that these properties be interred from the conduction characterrsties alone. In the work to he described, all the cleaving was done in a high vacuum just prior to the evaporation of metal elertrodes so as to avoid air contamination at the interfaces. Results of these studies indicate that the current through the 30 and 40Å films exhibited quantitative agreement with the theoretical voltage and temperature dependence derived by Strallon for the tunneling of electrons directly from metal to metal. Thicker films at room temperature exhibited volt-ampere curves suggesting Schottky emission of electrons from the cathode into the conduction band of mica. However, the thermal activation energy was smaller than that found from other measurements, and the experimsntal Schottky dielectric constant was larger than the square of the index of refraction. These facts would indicate that the electrons were being injected into polaron stales ill the iusulator. At low temperatures and high fields, the current through the thicker films did not exhibit the Fowler -Nordheim dependence as would be predicted by a simple extention of the theory of field emission into a vacuum. THE mechanism of electrons tunneling through insulating films has received considerable attention in the last few years due to the devices possible utilizing tunneling'-4 and the success of tunneling in the study of superconductivity.5,6 Until the recent paper by Hartman and chivian7 on the study of aluminum oxide, there had been no reported successful quantitative experimental fit to the theory. Their method of fabrication necessarily results in a polycrystalline insulator, the stoichiometry of which is nonuniform from one side to the other. This structure also introduces complications to the shape of the barrier which is set up by the insulator since the insulator possesses a spatially nonuniform band structure and dielectric constant. Due to these facts an analysis of the data in terms of a pviori barrier shape is of questionable validity. The use of muscovite mica not only overcomes these disadvantages but, as an insulating thin film, provides physical properties (dielectric constant. trapping levels and their densities, forbidden energy gap, and so forth) that are identical to the easily measured values of the bulk sample. Furthermore, it is a single-crystal insulator whose cleavage planes (10Å apart8,9) provide uniformly parallel surfaces of well-known separation. This material is therefore ideally suited to the study of electron-transport phenomena. Von Hippel10 using a 6.5-µ-thick sample was the first to observe the high-field conductivity (=5 x l06 v per cm) of mica. No attempt was made to develop an empirical formula, but Von Hippel concluded from intuitive arguments that the current was being space-charge limited by trapped electrons. Mal'tsev11 in a more recent investigation at high fields observed a dependence of the conductivity a on the field F of the form exp(ßF1/2). This dependence was attributed to the Frenkel effect,12,13 a Schottky type of emission from filled traps. No mention in the English abstract was made of the thicknesses of his samples or, and more important, of how well the value of ß fit Frenkel's theory. In 1962 Foote and Kazan14 developed a technique for splitting mica to a thickness of less than 100Å and observed a dependence of the current density j on the field of the form j = jo exp(ßF1/2) on a thin sample thought to be 40Å thick. Assuming that this was a Schottky emission process and that the appropriate dielectric constant for such a mechanism would be closer to a low-frequency value of 7.6, Foote and Kazan calculated from ß an independent thickness of the mica of 36Å. No further investigation was made of the phenomenon. However, the work reported in this paper indicates that the film measured by Foote and Kazan was probably 60Å thick, the error arising from the measurement of the very small metal-insulator-metal diode areas that were used, along with the diode capacitance and dielectric constant, to calculate the thickness. In the research reported in this paper, Foote and Kazan's technique was modified to cleave muscovite in a vacuum of 10-6 Torr, immediately after which metal electrodes were evaporated creating Au-mica-A1 diodes. Aluminum was chosen because of its strong adhesion to mica, as necessitated by the

Jan 1, 1965

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management's most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of ' particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10' which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers' approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article' describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

By R. J. C. Tait

INTRODUCTION Process Control at the Ecstall Concentrator begins in the open pit at the Kidd Creek Mine. While this paper, naturally, emphasizes the instrumental and technical features of the Process Control system within the concentrator itself, it would not be complete without some mention of the selective mining methods and grade control practices at the mine, and of certain features of plant design, which are simple, but highly effective, elements of the Process Control system. The success of the entire Process Control system, from pit to concentrate load-out, owes much to the high degree of cooperation and mutual understanding among all the operating departments at Ecstall Mining Limited and to the willingness of management to accept, from the start, an overall control philosophy based upon the inter-dependence of mining and metallurgical operations. INFLUENCES OF MINERALOGY AND METALLURGY ON MINE PLANNING AND PLANT DESIGN Mineralogically, the Kidd Creek ores are fine grained and mostly very complex. Because of complex mineral associations and extensive inter-locking, very fine grinding and regrinding of middling fractions are necessary and selective flotation requires a very delicate touch. Four separate concentrates are made for shipment to copper, lead and zinc smelters. The Process Control system is tailored to the metallurgical objectives of maximum recoveries of copper, lead, zinc and silver into concentrates of optimum quality, for maximum economic returns. For example, zinc and lead in copper con-

Jan 1, 1970

By George F. Comstock

It seems a common opinion among metallographists that all light-gray inclusions seen with the microscope in polished sections of steel are manganese sulphide. Examples of this belief are continually appearing, as for instance in the paper by Dr. Henry Fay on manganese sulphide as a source of danger in steel railsll and in Lieutenant-Commander Cook's paper on Metallography of Steel for U. S. Naval Ordnance.² Slate- colored inclusions are considered to be silicates, and dove-gray inclusions, manganese sulphide. To show the danger in the latter unqualified assumption, it should be sufficient to examine the edge of any piece of steel that is covered with a fairly thick scale, and that has been polished in such a way as to prevent the scale from breaking away entirely below the polished surface. This can be done by protecting the scaled edge of

Jan 1, 1917

By T. M. Geffen, J. L. Sanderlin, F. F. Craig, D. W. Moore

Scaled reservoir models have been used to study the effect of gravity on oil recovery performance in frontal-drive operations; namely, water, gas, or solvent flooding. The difference in density between the reservoir oil and the injected fluid causes their segregation, resulting in a non-uniform advance of the fluid front. In the laboratory flow tests, which simulated both five-spot and linear injection operations in flat reservoirs, the viscous, capillary, and gravity forces present in these operations were scaled. Dyed fluids were used so that the gross movement of the injected fluid could be observed. The studies covered a range of injection rates, formation thicknesses, and rock and fluid properties normally encountered in field operations. The results of the model tests indicate that the volume of the reservoir contacted by the injected fluid at its breakthrough into the producing well is less than that expected based on information which neglects gravity effects. This difference can often be as much as 80 per cent by gas or water injection in uniform sand bodies. Preliminary flow tests on a non-uniform sand body indicate that the uniformity of the flood fronts may in some situations be influenced to a much greater degree by permeability variations within the rock body than by gravity effects. The magnitude of fluid segregation due to gravity is controlled by the average injection rate, rather than day to day or week to week variations. INTRODUCTION One of the important factors controlling the oil recovery from a frontal-drive operation, such as water, gas, or solvent injection, is the volumetric sweep efficiency. This factor is a measure of the gross portion of the reservoir that is contacted by the displacing fluid. The volumetric sweep efficiency is influenced by gravity effects, well arrangements, and variations in rock permeability within the reservoir. The gravity effects are due to the displacing fluid being of different density than the reservoir oil. This causes the displacing fluid to move preferentially toward either the top or bottom of the formation. Non-uniform advance of the flood front can be caused by the relative positions of the injection and production wells. Variations in rock permeability also result in an uneven advance of the displacing fluid. Gas zones, representing paths of low resistance, may result in non-uniform movement of the injected fluid. The more uneven the advance of the displacing fluid, the lower is the volumetric sweep efficiency and thus the lower the oil recovery efficiency. The effects of well arrangement and permeability variations, upon the gross movement of the injected fluid have been the subjects of extensive investiga-ti0ns.1,2,3,4,5,6 Gravity effects have been recognized as being present in frontal-drive operations'.' but there has been little quantitative measure of their magnitude. Very likely the reason gravity effects have not been studied is that this problem does not lend itself to simple experimental or mathematical analysis. The development of reservoir modeling techniques has made possible a quantitative determination of the effect of gravity on fluid segregation and thus upon the oil recovery performance of frontal-drive operations. This paper presents a progress report on a laboratory investigation of gravity effects in fully liquid-saturated, horizontal, uniform as well as non-uniform systems. These results were obtained from scaled experiments on both linear and five-spot systems within the range of conditions normally encountered in secondary recovery operations. This study is concerned with the gross movement of the injected fluid to the time it first reaches the production wellbore. Therefore, it should be emphasized that the results of this paper can not be used to determine the effect of gravity segregation on oil recovery efficiency at abandonment conditions. MODEL SCALING The science of scaling models is relatively new as applied as petroleum production problems, Many of the scaling techniques have been adaptions of those used in basic studies of heat and fluid flow. There are

Jan 1, 1958

[ ]

Jan 1, 1938