Search Documents

By Jerry L. Straalsund, D. Bruce Masson

A dew-point technique was used to determine the thermodynamic activity of zinc at 430°C in a series of e phase Ag-Zn alloys. The composition of the alloys ranged from 72 to 88 at. pct Zn. This range included the composition at which Massalski and King3 found a reversal in the composition variation of the crystallo-graphic c/a ratio, which they attributed to an overlap of the Fermi surface across the (002) faces of the Brillouin zone. The data is presented in a graph in which RT In yz,, where yz, is the activity coefficient of zinc, is shown as a function of atomic percent zinc. This curve has an unmistakable change in slope at the same composition that Massalski and King observed the beginning of the reversal in the c/a ratio. This change in slope of the thermodynamic data is also attributed to a Brillouin zone overlap. Equations are presented to demonstrate that the thermodynamic activity can be related to the density of states of the conduction electrons, and that the observed phenomena are consistent with this model. It is also demonstrated that the contribution of the density of states can be related to the excess stability, a phenomenological parameter recently shown by Darkeen" to be significant in the interpretation of thermodynamic data of metallic phases. The data seem to indicate that zone overlap has caused a spinodal point, and the resulting misci-bility gap, in the phase diagram. THE problem of developing an adequate thermodynamic model of solid solutions has proven to be difficult, and is still only partially solved. The main approach has been to develop a statistical model, such as that of an ideal solution, regular solution, and so forth, to which can be attached corrections for electronic, vibrational, magnetic, ordering, or other contributions. Such corrective terms are usually derived on an ad hoc basis, and it is difficult to predict in advance what their relative importance will be. This problem has been discussed in general terms by Oriani and Alcock,' who have reviewed several thermodynamic models and a few empirical correlations. The measurements described in the present paper were made to demonstrate in a special case the importance of one such corrective term, the contribu- tion of the energy of the conduction electrons of an alloy. It was our premise that the contribution of the energy of the conduction electrons to the thermodynamic activity of the alloy components could be detected; further, that such an effect would be observed at alloy compositions where other phenomena, also ascribed to the energy and density of states of the conduction electrons, are observed. The idea of the importance of the conduction electrons is hardly new. Hume-Rothery and his adherents have developed the well-known theory of alloy phases in which the sequence of phase fields in binary equilibrium diagrams, especially those involving the noble metals with the IIB, IIIB, and IVB subgroups, can be correlated by replacing the composition variable with the ratio of conduction electrons to atoms, e/a. Jones and others have developed a physical explanation for this correlation, in which they consider the solubility limits of phase fields to be restricted by an intersection between the Fermi surface and a Brillouin zone. The general features of the model are also quite well-known—presumably zone intersection causes the density of states to decrease at critical alloy compositions. The attendant increase in energy of conduction electrons in the original crystal structure allows an alternate structure to become more stable as the concentration of polyvalent solute is increased. In spite of the wide acceptance of these ideas on phase stability, there is only indirect* evidence, such as the variations in lattice parameter recorded extensively by Massalskizy3 and others, that Brillouin zone interactions occur. There are few experimental measurements, other than the correlations of the phase sequence, that substantiate the premise that the energy of conduction electrons affects the solubility limits of alloy phases. Much thermodynamic data of alloys has been found to be consistent with the theory; yet there is a lack of detailed data at compositions where zone intersection and overlap are thought to occur. One would expect that the energy of the conduction electrons would make a measurable contribution to the thermodynamic properties of alloys at compositions near zone intersection and overlap if the theory of Hume-Rothery and Jones is correct. This conclusion cannot be avoided, because the phase boundaries are determined by the requirement that the chemical potential of the components be equal in both phases at equilibrium. An electronic effect large enough to alter the stability of a phase should also affect the thermodynamic activity by a measurable amount.

Jan 1, 1969

By A. G. H. Anderson, Eric R. Jette

A few years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and siliconl,2 some information on microstructures and hardness, not incorporated in the published work, alas obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it may have in connection with the constitution of the alloys. Microstructures Referring to the iron-chromium-silicon diagram,' the regions that received most attention were those in which the sigma phase appears. It was found that the mode of occurrence of this phase varied much with the condition under which it mas formed, and the mode influenced considerably the hardness of the alloys. In some slowly cooled alloys, well within the alpha + sigma-phase boundary, sigma occurs in pabterns suggesting a eutectic. The structure of such an alloy is shorn in Fig. 1, showing it to be partly coarsely laminated and partly globular mottled. In other annealed and slowly cooled alloys, the lanlinated structure is entirely absent, and sigma appears in an irregular distribution of sharply cornered elongated areas (Figs. 2 and 3). These areas all possess a more or less mottled structure. A carbide phase is also visible in these two photomicrographs; it is represented by bright white arras of various shapes, sometimes apparently enveloping the sigma. Quenched and aged specimens, whose compositions arc: located near the phase boundary between alpha and sigma + alpha regions, have structures not unlike martensite (Figs. 5 and 6). Fig. 4 shows the structurc of alloy No. 35 as quenched from 1100" C.; it is a typical solid solu-

Jan 1, 1938

By N. A. Zeigler, T. D. Yensen

Aging is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more constituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the A1 transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, O, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2. Based on the theory that magnetic properties are intimately connected with the regularity of the lattice, it now follows quite logically that a greater effect on this regularity may be obtained when the above impurities are precipitated as very fine particles of Fe3C, Fe4N, FeO, etc., more or less uniformly dispersed within the grains. But if this is the case, it follows also that there must exist a relationship between the size

Jan 1, 1935

By A. Andreas, E.H. Wells

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

By George H. Ashley

Mining, including quarrying, dates back almost to the dawn of history, beginning almost with the beginning of what we call civilization. State surveys date back about 100 years. Evidently mining flourished for thousands of years before state surveys were thought of. Why should it not continue to flourish without state surveys? First, it may be noted that as mining and civilization were contemporaneous, so state surveys and the science of geology were almost contemporaneous. As recently as 30 years ago the United States mineral laws were interpreted to mean that coal lands in the public domain were only those lands on which workable coal outcropped. The half billion acres of public land underlain by .coal but on which it did not outcrop were treated as homestead lands and open to settlement. Just what did the science of geology do to or for the mining industry? Until geology arose rocks or minerals or ores were where they were found. Their finding might be accidental, or might be the result of deliberate search or prospecting. In open, rocky country, with little or no vegetation, as in parts of the West, prospecting served very well, though at an enormous expenditure of human time and effort, if not money. The old saying that every dollar's worth of gold taken from the earth has cost two dollars may largely be charged to the time value of the usual method of prospecting. Geology changed all that. The science is still young and it still labors under handicaps of immaturity and early errors. Geology, however, has gradually been discovering the relations and conditions under which the several mineral deposits occur. Its elaborate studies of exhausted or nearly exhausted mineral deposits has done for it what human autopsy has done for medicine and surgery. Perhaps in no field is this plainer than in the oil and gas industry. Note might also be made of several important coal fields in England and on the Continent, in which the coal is everywhere deeply buried. Passing over the long period of growth during the past 100 years, geology today is prepared to offer the mining industry: first, a knowledge of the geologic conditions under which most minerals occur and to explore

Jan 1, 1935

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By Eugene Jablonski

Statistical data on the Polish producing business are available only for the first half of 1939. Because of the invasion of the country during September by Germany and Russia all sources of information have stopped, and it is impossible to get even an approximate picture of the status of the industry after that date. The long declining trend of Polish production, which was finally checked during 1938, kept a further upward tendency during the first half of 1939, and there is good reason to believe that the upward trend would have been maintained. It is true, there was little hope of reviving the slowly dying Boryslaw field, although there still remained a slight possibility for an extension in its southwestern direction. Repressuring plans were still discussed, but. could not be put into effect because of extremely complicated and split-up lease ownership. The Gorlice-Lipinki ficld continued to be the main factor in the increase of the country's production. During the first half of 1939 this field received a further important extension in a southern direction. The Schodnica field continued to use repressuring with success. At the end of June, 21 exploratory wells were drilling, 14 of which were within thc Carpathians and 7 in the Miocene geosyncline of the Carpathian Foreland. All of the wildcat wells drilled within the Carpathians were on the struct,ural cxtcnsion of old established fields, but part of the wildcats of the Foreland were on new geological and geophysical prospects. The Opary gas field of the Foreland discovered last year has been further developed. The Government-owned Polmin completed its third gasser. This well penetrated two sands; the upper one, 118 ft. thick, was found at 1312 ft., with an initial pressure of 570 lb. and capable of produeiring 10 million cu. ft. per day. The second sand, 91 ft. thick, was found at 1690 ft., yielding 20 million cu. ft., with a pressure of 760 lb. The well Mieczyslaw, drilled about 3 miles further north on the flank of the structurc, found the first sand watered. The Pioneer No. 5, at Chodonice near Przemysl, which reported somc gas last year, was 5696 ft. deep at the end of June, still drilling in Miocene. Anothe well in the same vicinity drilled by the Gasolina was 1708ft. deep.

Jan 1, 1940

By Milan Matula

One of the main characteristics of the development of rock mechanics in some countries is a close cooperation between experts in rock mechanics and workers in related fields, including soil mechanics and engineering geology. The purpose of this chapter is to outline the contribution that engineering geology can make to rock mechanics and to present a few examples of engineering geology studies that have been used in solving some practical rock mechanics problems. Engineering geology investigations dealing with the influence of geological factors on the physical properties of rock materials and rock masses fall into three main categories : 1) Systematic study and correlation of the physical properties of the main rock types with the petrogenetic evolution that caused the differences in the properties of these various rock types. 2) Study of the heterogeneity and anisotropy of both rock materials and rock masses. 3) Delimitation of rock masses which are approximately uniform in physical properties (quasihomogeneous units). Delimiting of the quasihomogeneous rock masses is the main contribution that the engineering geologist can make to rock mechanics. This delimiting is based on the evaluation of many complex geologic factors, not on test results alone, and therefore is most effectively done by trained engineering geologists. The foregoing types of studies are being used in Czechoslovakia for several purposes, including : 1) the compilation of regional engineering petrologic data-that is, the systematic definition of the main rock types of the country in terms of their representative physical characteristics;

Jan 1, 1970

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By J. C. Smock

The magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

By E. H. Wells, A. Andreas

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

The Jeffrey Company Opens Branch in Seattle The Jeffrey Manufacturing Co. of Columbus, Ohio, announces the re-opening of its Northwestern Branch Office at Seattle, Wash., and the appointment of Mr. Percy E. Wright, Consulting Mechanical Engineer, as District Manager for Oregon, Washington, Alaska, British Columbia and Alberta. Mr. Wright, who has been in the Northwest since 1910, and whose connection with the Jeffrey company dates back to 1902, has' had a wide and varied experience and training in the handling of the Jeffrey line which will enable him to be of great assistance to customers in solving their elevating, conveying and transmission problems. Trade Catalogs To a majority of the public, the name 'DuPont suggests military powder-munitions of war. The DuPont Products Book A-430 (April, 1916) lists 251 distinct commodities made. and sold by this company, many of which are far removed from destructive work. Mining men are fully cognizant of the need for explosives in constructive work, but they may be surprised to know that side by side with the powder and dynamite this company manufactures such peaceful articles as substitute leather, combs and collar buttons. The substitute for leather is Fabrikoid, varying in weight from a quality light enough for bookbinding to one heavy enough for trunks and automobiles, and the combs and collar buttons (with scores of other articles) are made from Pyralin. The book also contains a long list of chemicals, and a shorter list of special products and miscellaneous materials such as charcoal, wood flour and saltpeter. The Jeffrey Manufacturing Co. of Columbus, Ohio, making elevating, conveying, crushing, screening and power transmission machinery, has just issued its. latest Bulletin, No. 177, :featuring self-propelling wagon and truck loaders for handling crushed stone, sand, gravel, clinker, coke, etc. These machines are described as having a capacity of 1 to 1 ½ cu. yd. of material per minute, with power to load crushed stone maximum size pieces through 3 ½ -in. ring and to load trucks or wagons in 3 or 4 min. The self-propelling device is designed to enable one man to operate the loader as it is fed into the pile, and to move the machine about under its own power.

Jan 7, 1916

By Geo. H. Ashley

THE present critical state of the supply, distribution, and utilization. of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibituminous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bitumi¬nous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coals by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by, which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service.

Jan 8, 1919

By R. A. Anderson, O. D. Sherby, J. E. Dorn

Solid solution alloying increases the plastic properties of aluminum at elevated temperatures by solid solution strengthening, by restraining recovery and recrystallization, and by a Cottrell effect. When binary aluminum alloys are strained and aged at 1940° to 300°K they develop a yield point. This is attributed to a migration of dislocations to solute atoms during aging. IN view of the ever expanding interest in applications of metals and alloys to high temperature service conditions, it becomes increasingly important to be cognizant of the effect of various metallurgical factors on the strength of alloys at elevated temperatures. One problem of wide interest, not only because of its engineering significance but also due to its fundamental scientific importance, is the elucidation of the effect of alloying elements on the plastic properties of homogeneous a solid solutions at elevated temperatures. It is indeed astonishing to note that in spite of its importance, and in spite of extensive random testing of alloys at elevated temperatures, no systematic investigation has been reported yet on the effect of alloying additions on the plastic properties of a solid solutions at elevated temperatures. This deficiency in our knowledge prompted the investigation described in this report. Rather extensive data are currently available on the effect of alloying elements on the plastic properties of a solid solutions at atmospheric and sub-atmospheric temperatures. Such data might be ex- trapolated to higher temperatures and reasonable guesses might be made regarding the influence of such factors as recovery and recrystallization in order to hazard a qualitative estimate of the effect of alloying elements on the plastic properties of a solid solutions at elevated temperatures. Such

Jan 1, 1952

By H. J. Fisher, J. L. Walter

Two types of Si-Fe columnar ingots with preferred crystal orientation have been produced: a) ingots with (0011 directions of the crystals parallel to the longitudinal ingot axis and b) seeded ingots in which all crystals have the (100) [001]orientation with respect to the sides of the ingot. Measurements of freezing rates and temperature gradients indicated that columnar freezing occurred as long as the temperature gradient ahead of the solidification front was greater than zero. THE development of preferred orientations or textures in wrought metals may be influenced by the presence of a preferred crystal orientation in the ingot from which the product was made. The deliberate introduction of preferred orientation in the ingot for the express purpose of producing a particular preferred orientation in the wrought product has not, to the authors' knowledge, been reported in the literature.* This report describes the prepara- tion of ingots of 3 1/4 pct Si-Fe in which preferred orientations near (100) [001] were produced. These ingots were subsequently rolled to strip, 0.012 in. thick, to provide a sufficient quantity of polycrystal-line sheet having the (100) [001] orientation or "cube-texture" to evaluate the magnetic properties. The properties; and test results showing the advantage of the cube-textured Si-Fe magnetic sheet over magnetic sheel having the (110) [001] texture or "Goss" texture have been reported elsewhere.' The rolling and recrystallization textures of single crystals of silicon-iron having orientations near (100) [001] have been studied by Walter and Hibbard.2 They found that if the crystal has an original orientation such that the (100) plane is within 30 deg of the rolling plane, the recrystallization orientation will approach (100) [001]. If the (110) plane is nearly parallel to the rolling plane,

Jan 1, 1962

By F. H. Labee

Questionnaires and special letters soliciting information were sent to a great many geologists, petroleum engineers, independent operators, and representatives of large companies in Arkansas, Louisiana, Texas and New Mexico. Replies to more than 50 per cent. of these letters were received. A survey of the facts and opinions presented in this correspondence will be made a little later, but first some of the general aspects of the problem will be reviewed. By "unit operation,"1 we mean the development and operation of a single entire pool, or reservoir, of petroleum by one management, on a systematic and scientific plan which is best calculated ultimately to extract from the pay sand and bring to the surface of the ground the largest possible amount of oil with the greatest possible total profit. No one, as far as the author has been able to ascertain, denies the advantages, both scientific and practical, of unit operation. All are agreed that it is sound in theory. It permits the proper distribution of wells, which should always be spaced on the ground according to a regular geometric plan with the intention of maintaining the same spacing all the way down and into the pay sand, or pay sands. This spacing will be different for different fields, depending on such variable factors as the lithologic character of the pay formation, the nature of the controlling structure, the depth of drilling, the viscosity of the oil, and so on. From the viewpoint of engineering practice, as applied to economical extraction of oil, there is no more important consideration than well spacing—well spacing in the pay formation, and not merely on the surface of the ground —for the method of well spacing has a direct bearing upon all such engineering practices as pressure control, repressuring by gas, the water drive, and SO on. H. C. Miller2 summarized the advantages of an ideal cooperative development plan as follows: "Among the more important advantages of

Jan 1, 1930

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By F. W. Jr. Sperr

THE byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.) 69 per cent. of coal Domestic coke (1/2 to 3/4 in.) 2 per cent. of coal Breeze (under 1/2 in.) 4 per cent. of coal Surplus gas, cubic feet per net ton 6600 Gas for heating ovens, cubic feet per net ton 4400 Tar, gallons per net ton 9 Ammonium sulfate, pounds per net ton 25 Benzols, gallons per net ton 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke,"' "beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writer1 stated that in brass-foundry practice, Connellsville coke is considered much superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in mak-

Jan 10, 1920

By R. G. Treuting, W. C. Ellis

D. Whitwham, M. Mouflard, and P. Lacombe (British Council Research Fellow, Labratoire du Professor Chaudron, Vitry-sur-Seine; Inqenieur de Recherches, Labratoire de Vitry; and Maitre de Recherches, Labratoire de Vitry, Professeur Adjoint de Metallurgie, Ecole des Mines, Paris)—The authors' work is of great interest in bringing out the geometrical relations existing between twinned lattices, and for the notion of a coincidence super lattice developed from this. We should like to point out that a similar idea was put forward by Friedel8 in his book on the subject of lattice merohedrism "merihedrie réticulaire:"—When two crystals A and B are twinned with respect to a mirror plane, there exists a common superlattice, "réseau periode," which is independent of the contact surface between the two crystals. The volume V of this superlattice is a simple multiple of the volume v of the lattice of crystals A, or B, (Fig. 5). This "multiple cell" is defined by the twin plane (p q r) and a row of atoms [h k l] normal to this plane, the base being taken as the smallest unit (two-dimensional) of this plane. Two cases must be considered. First when the multiple cell, as defined, has no atom site at its center nor at the center of its faces other than (p q r), v the twinning index is defined by —. In the second v case, when one of the two above conditions does not v apply, then the twinning index is V 2v A more intuitive definition of the twinning index would be the proportion of atoms of C, which would coincide with those of C1 when the C, lattice is imagined to extend on the other side of the contact surface. In the case of cubic crystals, the twinning index

Jan 1, 1952

By Eric R. Jette, A. G. H. Anderson

A few years ago, while the writers worked on the constitution of ternary and quaternary alloys consisting mainly of iron, chromium and siliconl,2 some information on microstructures and hardness, not incorporated in the published work, alas obtained. It has not been possible to do any further work on the properties of the alloys. The information possessed is hereby presented for the interest it may have in connection with the constitution of the alloys. Microstructures Referring to the iron-chromium-silicon diagram,' the regions that received most attention were those in which the sigma phase appears. It was found that the mode of occurrence of this phase varied much with the condition under which it mas formed, and the mode influenced considerably the hardness of the alloys. In some slowly cooled alloys, well within the alpha + sigma-phase boundary, sigma occurs in pabterns suggesting a eutectic. The structure of such an alloy is shorn in Fig. 1, showing it to be partly coarsely laminated and partly globular mottled. In other annealed and slowly cooled alloys, the lanlinated structure is entirely absent, and sigma appears in an irregular distribution of sharply cornered elongated areas (Figs. 2 and 3). These areas all possess a more or less mottled structure. A carbide phase is also visible in these two photomicrographs; it is represented by bright white arras of various shapes, sometimes apparently enveloping the sigma. Quenched and aged specimens, whose compositions arc: located near the phase boundary between alpha and sigma + alpha regions, have structures not unlike martensite (Figs. 5 and 6). Fig. 4 shows the structurc of alloy No. 35 as quenched from 1100" C.; it is a typical solid solu-

Jan 1, 1938