Search Documents

By D. S. Hutton, W. C. Leslie

S. Floreen (1nteumtio)lal Nickel Co.)— One fairly simple way to differentiate between embrittlement due to surface microcracks or due to a dislocation barrier effect might be to load a brittle rock salt crystal in tension to some stress just below the fracture stress and then immerse the loaded crystal in water. If a surface film is retarding plastic flow then one should observe some plastic deformation of the rock salt as

Jan 1, 1962

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of area prior to urban development population and aggregate consumption trends in Austin, TX, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby areas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1982

By Fred B. Ely

The first recorded production in the Dutch East Indies was in the year 1893 but seepages of dl were known to exist in North Sumatra, East Java and the east coast of Borneo at least as early as 1880. During the Of the above amount the Royal Dutch produced............................................. 36,006,079 Nederlandsche Koloniale Petroleum Maatschappij (subsidiary of Standard Oil of New Jersey)....................................... 3,867,769 Total Dutch East Indiea....................................... 39,873,848

Jan 1, 1931

By R. P. McNitt

TITANIUM hydrides have received considerable study in recent years because of the adverse effects of the hydrides on mechanical material properties such as ductility and tensile strengths. Generally speaking, as the hydrogen content increases, ductility and strength levels decrease. While the amount of hydrogen present in commercial titanium is negligible, hydrogen may enter the material during welding, electroplating, and so forth. The hydrogen will then precipitate, in the form of titanium hydride. If the material

Jan 1, 1968

By Michael Poole, Joseph M. Chelini

Most earthmoving operations using off-road, rubber tired production equipment have abnormally high total tire costs. Achieving informational control over 7 direct and 2 indirect tire cost centers can reduce tire costs more than 50 percent; a 20 percent savings is often guaranteed. This is achieved by utilizing available computer software and implementing tire information management through the engineering deparatment.

Jan 1, 1983

By H. R. Joesting

Geophysical search for minerals is stepped up to meet requirements of expanded defense program - Seismic and electrical surveys become firmly established for ground-water and engineering investigations.

Jan 2, 1953

AIME 1953 DIRECTORY SUPPLEMENT COMMITTEES NOMINATING E. H. Rose, Chairman R. E. Byler J. F. Myers Grover Molt S. W. Engelmann S. J. Swainson EDUCATION A. C. Dorenfeld, Chairman G. P. Lutjen A. E. McHugh H. Rush Spedden T. G. Chapman T. M. Morris T. Barker S. R. B. Cooke W. O. McClintock

Jan 1, 1953

By T. Airaksinen, R. T. Hukki

A new static pneumatic classifier for the primary separation of the feed material for microclassification is discussed. Pilot plant test results and a novel flowsheet for microclassification at the industrial scale are presented.

Jan 1, 1980

By Leonard P. Colvin

Like all successful American enterprises, the mining industry is constantly trying to increase production, lower costs and improve working conditions. Companies are, of course, intensely interested in new equipment to help them gain these important ends, and one recent development-the mechanical raise climber--contributes to all three goals. Properly used, it increases production, cuts costs and has a number of important safety aspects all of which are the subject of this article.

Jan 1, 1962

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35° to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum.

Jan 10, 1953

Jan 1, 1970

By Ned Kuenhold

AN equipment manufacturer swallows a bitter pill when he sees his machinery improperly in- stalled and not used to the full potential. This frequently happens with vibrating screens. Screens can be classified according to the path of vibration imparted to the screen surface. On this basis there are: 1) vertical circle or modified circle throw, 2) horizontal circle or modified circle throw, 3) vertical linear reciprocation, 4) tilted linear reciprocation, and 5) horizontal linear reciprocation. The most versatile vibration for medium to coarse sizing is generally conceded to be the vertical circle produced by an eccentric or unbalanced shaft, but other types of vibration may be more suitable for certain screening operations, particularly in the finer sizes.

Jan 6, 1957

By John M. Pitt

Shear strength assessment and the associated variability in rock masses historically have been hindered by high costs and biases in laboratory testing programs. An in situ direct shear device was developed on the principle of the previous borehole shear device for soils. Using wedge action to simultaneously apply normal and shear stress to an envelope of material on the periphery of a borehole, the device develops a complete Mohr-Coulomb failure envelope. Tests performed in homogeneous materials show expected strengths and their variability equivalent to laboratory tests. However, tests in a structurally non- homogeneous coal did not display significant variability. A 38 mm diam borehole was used in this work; however, larger or smaller bore- holes may also be used within the size limits of the device. The device is employed in holes commonly drilled for rock bolt placement, at 1 to 2 minutes per test.

Jan 1, 1984

By R. P. Killmeyer, B. S. Gottfried, J. T. Wizzard

The US Department of Energy's Coal Preparation Branch has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Comparisons are made between performance criteria calculated by hand and the performance criteria calculated by the program for 120 different dense medium cyclone tests. Results show that the computer program gives results in close agreement with hand-calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1984

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By Wayne D. Gould, Robert S. Shoemaker

Modern mill design is a combination of many factors which permit the efficient production of a mineral concentrate from operating, maintenance, and capital requirements. In general, mills should be designed to use the largest possible equipment compatible with the requirements of the ore and the owner's operating philosophy. The paper discusses the major parts of concentrating mills, from primary crushing through comminution, both conventional and autogenous, and the production of a final concentrate. Features of various plants are compared and discussed in the light of operating practice and maintenance requirements.

Jan 1, 1978

By H. R. Hardy

The study of the mechanical properties of geologic materials was initiated in the Mining Research Section of the Fuels and Mining Practice Division in 1951 as part of a fundamental study of ground stress in Canadian coal mines.1 Early in the investigation of the mechanical properties of geologic materials, however, it was realized that the test results are influenced by the rate and the duration of loading. For this reason, laboratory investigations2,3 were undertaken to study the effect of long-period uniaxial stress on the deformation and failure properties of these materials. A literature survey indicated that work on the time-dependent properties of geologic materials had been very limited in the past.

Jan 1, 1965

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole.

Jan 8, 1954

Jan 1, 1969

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980