Search Documents

By A. S. Nowick, E. S. Machlin

One of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.' During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time requird for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error This method of showing stress-rupture data has been adopted by many investigators and the NACA.' By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, roo, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time lor rupture on stress, temperature, composition, and structure. In order to obtain this information, an investigation was made at the NACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given composition and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efliciency and power output of gas turbines used in aircraft propulsion can be increased. Theory The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 developed by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate-process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process." For example, in a chemical reaction the unit process is

Jan 1, 1948

By R. H. Swallow, George Hess

The purpose of presenting this paper is to show: 1. The applications of aerial photography to the map requirements of strip mining. 2. The methods and procedures for producing accurate aerial contour maps. 3. The advantages of aerial contour mapping over stadia or plane table methods. Introduction Aerial photography was once a crude, uncertain tool. 'Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques. Then, some farsighted engineers and aerial photographers found that if the camera's axis were vertical to the earth's surface, these pictures could be the source of valuable mapping information. By viewing these pictures in stereoscopic pairs, accurate measurements could be made and contour maps produced from this aerial photographic base. So the aerial mapping business developed, using the plane and aerial camera to collect the data, working with skilled ground parties who established a network of ground control for this map information photographed from the air. Over the following years, a whole new science developed, known as photogrammetry. Precision cameras and lenses were perfected, and the narrow view of the surveyor's transit was broadened to the vast perspective of the mapping plane. Stereoscopic Coverage Obtained Today in making aerial topographic maps, aerial photographs are exposed so that full stereoscopic coverage for the survey area is secured. To obtain true elevations these photographs are processed through a series of precision measuring and contouring instruments which employ a principle similar to the military range finder. Here is how aerial mapping is being used by your industry. Topographic maps are but one of three products from aerial photographic surveys. First, there are the individual photographs. These are taken in flight strips, exposed with an overlap, just as shingle on a roof overlap. Exposures are overlapped from 55 to 60 pct along the line of flight so that a large part of the area in one picture also appears on the adjacent photograph. Successive strips are flown with a side-lap of between 20 and 25 pct. Each point on the ground thus will be somewhere near the center of at least one photograph in the series. They may be studied under a stereoscope and relief seen in a third dimensional effect. Geologic features that may go unobserved in ground exploration are often detected under stereoscopic inspection. Moreover, though field checking is not obviated with these aerial photographs, it is directed toward critical areas and toward worthwhile anomalies. Aerial Photographic Mosaics The second product of an aerial survey is the photographic mosaic. This is an assembly of carefully matched aerial photographs in mosaic form. Although not as accurate as the topographic map, it does reveal a wealth of cultural detail in true relative scale. Since the mapping plane is flown over the area at a fixed altitude, the peaks and valleys are pictured at different scales. During compilation these scale differences are compensated by adjusting one vertical picture to another according to plotted ground control positions. Only extreme variations in ground elevation cannot be

Jan 1, 1950

By R. A. Salathiel

A new synthetic material has been developed which is highly effective in treating drilling muds to reduce filtration rate. The material is the soluble salt of a very high molecular weight condensation product of sulfonated phenol and formaldehyde (SPIF). Laboratory tests show that SPIF is effective in muds of all salinities varying from fresh water to saturated salt water. Alkaline materials. such as soda ash or caustic and quebracho, may be used in combination with SPIF to advantage, and are essential in muds containing saturated salt water. In a field test where the water used in the mud had a salinity of about one-half that of sea water, SPIF in combination with caustic and quebracho made a very satisfactory mud. SPIF does not ferment. but due probably to additional polymerization a slight decrease in effectiveness is found when it is subjected to high PH and high temperature for a long time. INTRODUCTION Drilling mud is essential in rotary drilling. The influence of variations in the different properties of a mud on its ability to perform the various functions in drilling of wells is thoroughly understood in some cases and poorly understood in others. For instance, the function of mud density in restraining high pressure fluids is simple and well known. On the other hand. while the value of low filtration is widely recognized, it is seldom possible to determine precisely what filtration rate is required for the mud to perform its functions properly. Filtration rate is important because it influences the ease of moving tools in or out of the hole. Filtration rate also affects the stability of the bore hole walls, which are subject to softening and degradation by aqueous filtrate. Difficulties in rotary drilling are often avoided by using low-filtration muds. Treatment of fresh-water muds to provide moderately low filtration rates usually consists of adding chemicals to improve the dispersion of the clays. To provide very low filtration rates, organic colloidal materials are added. Among the materials hat are used in this way are starch, natural gums, and altered celluloses. In muds that contain large amounts of salt or calcium or magnesium ions, the clays are coagulated and, as a consequence, the filtration rate is undesirably high. In such muds organic colloids are of great importance. LIMITATIONS OF PRESENT FILTRATION ADDITIVES Starch and water-soluble gums are widely used as filtration control agents. Starch is the most important material of this kind being used. It has the advantage of relatively low cost. It is effective in promoting low filtration rates, not only in fresh water muds, but also in muds containing large amounts of salts. However, both starch and natural gums are subject to fermentation and must be preserved from damage caused by microbiologic attack. Also, both starch and natural gums tend to increase the mud viscosity undesirably. Furthermore, the quantity of material required may be quite large. This is especially true when substantial amounts of salts are present. In such a case small addition* of starch may increase rather than reduce the filtration rate of the mud. Carboxy-methyl-cellulose, a chemically altered form of cellulose, has some advantages over starch. It is effective in smaller concentrations and does not increase the viscosity as much as

Jan 1, 1952

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-' Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema' have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By E. R. Force, W. F. Cannon

Many large high-grade manganese deposits occur in marine-transgressive sedimentary sequences deposit fed on stable platforms, although the manganese mineralogy varies from carbonate to oxide facies and host lithologies vary from carbonate- to clay-dominated sections. Examples include the Nikopol and related deposits of the Soviet Union and Groote Eylandt, Australia. Recent work has shown that high sea-level stands are synchronous with stratified and stagnant oceans. We suggest that during transgressions and consequent anoxic events, the anoxic deep waters rich in dissolved manganese were dilute ore-forming fluids. Manganese was precipitated on the oxidized side of oxidation and alkalinity interfaces on shallow shelves. Where the precipitate was preserved, manganese ac- cumulated into ore deposits. Sedimentary manganese deposits have not been widely explored for in North America, nor are they always obvious in outcrop. Large areas of North America are underlain by rocks that we consider broadly favorable for such manganese deposits, and the disparity between the high potential but significant reserves of the United States is difficult to reconcile. Important undiscovered deposits seem likely. An area of Cretaceous rocks in South Dakota is presented as a possible location for a United States deposit analogous to foreign deposits described herein.

Jan 1, 1983

By CLYDE M. EYE

THE Sub-province of Benguet is in the North Central part of the Island of Luzon. Baguio, the capital, is situated on a piateau 5000 ft. above sea level, and is the main health resort of the Philippines. It is rapidly becoming the favorite resort for the China Coast as well, and has many miles of beautiful, curving drives with nearly every pine-covered knoll surmounted by a summer home. The United States Army has a recreation post here, known as Camp John Hay, with a well-equipped hospital, and there is a Country Club with a good golf course adjacent. The weather during the winter months and until late spring is ideal. The business center consists mainly of Chinese and Japanese stores, several hotels, and a large public market, in which are displayed all of the vegetables of the temperate zone, which are flown near Baguio, and many tropical and other products brought up from below. This district is reached from the Coastal Plain either by the old Benguet road built in 1904 by the United States Government, or by the Naguilian road, built some years later. The former is now a toll road, with a line of stages operating over it to and from Des Mortes in connection with the government-owned rail- road. Auto travel from Manila is also along this road, the trip from Manila to Baguio requiring about seven hours, following up the great valley north of Manila for nearly 150 miles to the lower end of the Benguet road, and thence to Baguio, 25 miles. This is an interesting, scenic trip; the road is especially famous for the zig zags where it climbs out of the canyon of the Bued River to the plateau. In the September number of the National Geographic Magazine, a fine aerial picture of this road, as well as of other interesting points in various parts of the Philippines, appears. Freight for the district is taken in mainly over the Naguilian road connecting with the railroad at Bauang. This route follows the ridges of the mountain slope with broad vistas and views of the coast.

Jan 1, 1930

By W. B. Hincke, C. G. Maier

Commercial processes of lead softening directly involve the behavior on fusion of mixtures of the oxides of antimony and lead, and the vapor pressures of these materials. Practically no quantitative data have been available for the discussion of lead softening from the point of view of the fundamental metallurgy of the process. The Pacific Experiment Station of the United States Bureau of Mines, in cooperation with the University of California, in the course of its program of study of the fundamental properties of oxides and sulfides, recently made vapor pressure measurements upon the various forms of pure antimony trioxide.1 When these measurements were considered in connection with the softening and "fuming" furnaces which are often used for lead purification, an unexpectedly anomalous condition appeared. In brief, this anomaly consisted in the fact that in certain softening furnaces, where lead bullion of approximately 1 per cent antimony content was being treated at a temperature of approximately 1300" F., no appreciable volatilization of antimony occurred, there being produced only a "skim" containing from 15 to 20 per cent Sb, 65 to 60 per cent Pb, as mixed oxides. In the "fuming furnaces," where the temperature was only about 1400" F. and where an accumulation of "skims" from the primary softener was being treated with certain other antimony-containing materials, a considerable volatilization of antimony as oxide occurred; an "impure" skim of some 60 to 65 per cent Sb and 10 per cent Pb was also produced as mixed oxides. The latter material cannot be suitably treated in hearth-type or softener furnaces. The essential chemical difference between the first and second step is the customary use of some reducing material (such as petroleum coke) in the later operation. An obvious interpretation of the effect of coke in facilitating the fuming of the antimony is the supposition that the antimony may be reduced to metal, and volatilized as such. This supposition is improbable, however, when it is realized that a slight extrapolation of the vapor-

Jan 1, 1932

By Charles Catlett

Having had charge during the past year of the operations of the New River Coke Company, the second largest, if not the largest, coke-producer in this district, my attention was called particularly to the yield of coke from the coal as coked in a bank of beehive ovens, as the record showed that this yield, while believed to be well up with the practice of the district, was much lower than the analysis of the coal indicated it should be. The coal is well known to many members of the Institute, and the scope of this paper does not include a discussion of its occurrence and development. It suffices to say that the New River district comprises the mines working on the coals of No. XII. or the Conglomerate Series of the Rogers brothers, which are located on New river and its tributaries, and which find an outlet for their product east and west over the Chesapeake and Ohio Railway. The New river through this section carries the drainage from an extensive peneplain in which it has formed a very striking and stupendous canon, probably the most striking east of the Mississippi river. The only practical access to this territory is by means of this canon and the Chesapeake and Ohio road, and the opportunities for development by other lines may be considered as nil. If it were not for the fact that this road, farther west, reaches and develops entirely different coals, which are found in other measures, the New River district might properly be spoken of (as is now done at times) as the " C and 0. field." For fuller information on the geology of the region, those interested are referred to the ery complete monograph on the subject by Mendenhall and Campbell of the United States Geological Survey. The rocks are the same as those which carry the more widely

Jan 1, 1900

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By F. Morgan, M. Muskat, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By C. P. Besse, N. F. LeBlanc

Described in this paper are oceanographic data which should be considered by an offshore design engineer and methods for developing a design wave height from the oceanographic data. The selection of a design wave is predicated on contemplated waves which might affect the site throughout the life of the structure. Selection of a design wave height may be based on (1) arbitrarily established recurrence Frequencies of hurricanes affecting the structure (predicted wave heights are associated with the expected variations of forces resulting from these waves) and (2) a risk-type evaluation wherein all possible storms affecting the area are considered (anticipated wave heights are associated with both investment plus risk costs and expected variations of forces). It is shown how the following oceanographic predictions are integrated into design considerations: (1) a classification of storm intensity which considers all recorded storms which affected the design area, (2) the recurrence interval of storms of a given- intensity (this interval is dependent on the extent of the geographical area considered in the design problem) and (3) a forecast of all wave heights which might affect the area (geometry of a structure often necessitates consideration of waves from a multiplicity of directions). The authors believe that the described techniques can result in selecting an adequate and reasonable design wave. INTRODUCTION Since the inception of offshore operations in the Gulf of Mexico, engineers engaged in designing suuctural facilities have been plagued with the problem of selecting an adequate and reasonable design wave. In the development of any offshore structure it is mandatory that the engineer evaluate the ability of the structure to withstand the ocean waves to which it will be subjected. Selecting such design waves quite naturally necessitates a coalition of the oceanographer and the design engineer. The oceanographer must provide a detailed knowledge of scientific principles which govern the behavior of waters in the Gulf of Mexico. He should also have an adequate knowledge of the manner in which design waves are utilized by the engineer. Although the design engineer's primary responsibility is applying the oceanographer's specialized knowledge in the creation of real structures, it is important that he possess some knowledge of related oceanographic principles to reasonably evaluate and apply the recommendations of the oceanographer. In the Gulf of Mexico it is the hurricane wind waves which generally govern the design of an offshore facility. The oceanographer must therefore develop techniques for predicting the heights, periods and frequency of all hurricane waves which might affect a particular structure. From this mass of oceanographic data, the design engineer must select the design waves which will apply to his particular design. PAST STUDIES ON FREQUENCY AND AMPLITUDE OF HURRICANE WIND WAVES Past oceanographic studies on the frequency of hurricane wave heights in the Gulf of Mexico have been devoted largely to predicting the recurrence interval of hurricanes which will generate maximum significant waves of given heights. The maximum significant wave height is the average height of the highest one third of the waves in that portion of the storm producing maximum wave heights. Since these waves occur over a relatively small portion of the storm (Fig. 1) and since the paths of hurricanes vary considerably (Fig. 2), the recurrence frequency of such heights is largely a function of the extent of the geographical area considered. In establishing the frequency of maximum significant waves for the entire American Gulf coast, the major fully developed hurricanes which affected the coastline from BrOwnsville, Tex., to Key West, Fla., were considered (Fig. 2). These Storms were selected and described by C. L-

By D. Turnbull, J. H. Hollomon

IN the most general sense, solidification refers to the formation of crystalline material from either a gas or a liquid. However, in this symposium, only the formation of crystals from liquids will be considered. Thus, in our present study the problem of solidification becomes that of determining the mechanism of the transition from a liquid to a crystalline solid, and our particular interest is in the transformation of metals from the liquid to the crystalline state. Metal liquids are seldom composed of only one kind of atom. Often solute atoms are added intentionally to make an alloy, or they may be present accidently because of incomplete purification. Furthermore, there may be small solid particles of various other crystals present in the liquid. Such small crystals may persist if their melting points are higher than any temperature to which the liquid is heated. Prior to solidification, the liquid metal usually is poured from one container to another. The second container, called the mold, usually is at a lower temperature than the container, or the crucible, in which the metal is liquified. The first solid that forms upon contact with the mold generally is of a different composition than the liquid, usually containing fewer foreign atoms or dissolved impurities. Heat is evolved upon solidification and is dissipated through the surroundings. Tree-like crystals, or dendrites, grow from the container walls and branch into the melt, enriching the remaining liquid in impurity atoms. In some alloys the remaining, relatively impure liquid continues to solidify until no liquid remains and the branches of the original crystal are cemented together. In other alloys, particles with a second type of crystal structure appear before solidification is complete. First the nature of the liquid and the solid states will be considered and then the mechanism of the initial formation of crystals from pure and alloy liquids. Later the problem of the growth of these crystals and the complexities of solidification in a mold, where the temperatures are not uniform and the composition of the melt changes continuously, will be discussed. LIQUID AND CRYSTALLINE STATES A liquid is an aggregate of atoms arranged with no apparent regularity (over distances of more than a few atom diameters). Nevertheless, any given atom generally has a definite number of nearest neighbors at definite distances, and thus order may be said to exist over a short range. In a crystal, on the other hand, a regular array of atoms continues for many hundreds or thousands of atom diameters, and a long-range order is apparent. Thus, a crystal having long-range order can be reproduced by linear translations for 10-5 cm or more of some fundamental unit possessing short-range order. A crude illustration of the difference between liquid and crystalline structures can be obtained by comparing the possible arrangements of oranges in a crate. If the oranges are simply dumped into the crate haphazardly until it is filled, the oranges will represent a static model of a liquid.

Jan 1, 1951

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

By M. J. Marcinkowski, K. S. Sree Harsha

A detailed numerical analysis has been made of the equilibrium configuration of partial dislocations in a blocked deformation twin under an externally applied stress. Twins made up of both pure screw and pure edge partials have been considered. The components of stress in the vicinity of the twin tip associated with each of these configurations have been plotted. It has been found that at some critical degree of oblateness the shear stress fields of the blocked screw or edge twin can both sPontaneously nucleate slip, whereas only the component of stress oxx about the edge twin can nucleate and propagate cracks. TWINNING becomes a predominant mode of plastic deformation at low temperatures and/or high strain rates. Fig. l(a) shows what must be the first step in the formation of a deformation twin, namely the formation of a loop of imperfect dislocation bounding a stacking fault. In an fcc crystal the partial dislocations have Burgers vectors of the type 1/6 a,(112) and the fault is of the intrinsic type while in the bcc crystal the partials have Burgers vectors of the type ao(lll). The stacking sequence of (111) planes in a perfect fcc crystal is given by ABC ABC, and so forth, and in one which contains a twin by ABCABACBA, and so forth. It is apparent that the stacking fault and twin give rise to no mistakes associated with adjacent close-packed planes; however, with respect to second-neighbor close-packed planes the faulted crystal has twice as many mistakes as the twin. The energy of the twin boundary may thus be taken to be one-half that of the intrinsic fault boundary. In the case of the bcc crystal the stacking sequence of (112) planes is given by ABCDEFABCD, and so forth, in a perfect crystal, by ABCDCDEFA, and so forth, in a crystal which contains a fault, and by ABCDCBAF, and so forth, in one which contains a twin. An analysis similar to that applied in the fcc crystal shows that both the fault as well as the twin involve no neighbor violations across adjacent planes. However, there are twice as many violations across second-neighbor (112) planes associated with the fault as compared to that of the twin. Thus once again the energy of the twin boundary may be taken as one-half that of the fault. It is important to note that, unlike the fcc, the faults in the bcc crystal involve first nearest-neighbor violations and are thus expected to be of much higher energy than those in fcc crystals. A more detailed analysis of the material discussed above can be found in Ref. 1. To a good approximation then, the lenticular twin shown in Fig. l(b) can be generated by adding partial dislocation loops on successive (111) planes for fcc crystals or (112) planes for bcc crystals in the manner shown, with no additional expenditure of chemical energy other than that required for the fault shown in Fig. l(a). In practice, deformation twins are much more extended than that shown in Fig. l(b) and more closely resemble one shown schematically in Fig. l(c). It is readily apparent that the free energy of the twin and matrix are identical. In those cases where the partials lead to a structural change, the free energy of the material contained within the dislocation array is lower than that of the matrix and we have the so-called martensite transformation. The present investigation is the first in a series of five major theoretical-experimental efforts which will deal with the static and dynamic behavior of twin nucleation and growth. There has been a recent surge in activity pertaining to the equilibrium shapes of twin lamellae2'3 and

Jan 1, 1969

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of- concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [Chemical Mineral Composition % Mn Hausmannite Mn304 72 Polianite MnO2, 63.1 Pyrolusite MnO24 60-63 Cryptomelane KR8O16R (R=Mn) Variable PsilomelaneBa Mn Mn8O16 (OH).45-60 CoronaditePb R8O16R (R=Mn) Variable Hollandite Ba R8O16R (R=Mn) Variable Manganite Mn2O3•H20 62 Braunite 3 Mn2O3•MnSiO3 62 Tephroite 2 MnO•SiO2 54.3 Rhodochrosite MnCO3 47 Rhodonite MnSiO3 42 Spessartite 3 MnO•AI2O3•3SIO2 33.3 WadHydrous Mn OxidesVariable Franklinite(Fe Mn Zn)O(Fe Mn)sO3 Variable Asbolan Cobaltiferous wad Variable AlabanditeMnS63.14] Geology From a geological standpoint most manganese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, US southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, MT. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1983

By M. Muskat, F. Morgan, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber' in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman' has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By D. M. Warner, Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as 8and-cast and as heal-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brine11 and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. The demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.' Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergran-ular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about 950" F., quenching in oil or in cold or boiling water, and artificially aging

Jan 1, 1926