Search Documents

By R. C. Rastogi, F. F. Aplan

The goal of this study is to evaluate the coal flotation process and the interaction of the chemical (reagent) and hydrodynamic (machine, operational) variables as they affect yield, flotation of various sized particles, and sulfur and ash rejection. Coal flotation is found to follow a first order process with the coal floating much faster than either pyrite or ash. This circumstance may be used to achieve gangue rejection during flotation. When floated with MZBC, cresol, or pine oil frothers, coal floats in the size sequence: 108 pm ( - 65 mesh), 589 x 808 pm (88 x 65 mesh), and 1.17 mm x: 589 pm (14 x 18 mesh). However with a substantial amount of fuel oil collector, all particles tend to float roughly in proportion to their content in the feed. An increasing aeration rate was found to be the most important variable in increasing the coal flotation rate. This increase in flotation rate, unfortunately, is also accompanied by an increase in the flotation rate of the pyrite. The rejection of pyrite during coal flotation is best accomplished at low aeration rates, low frother concentrations, and low impeller speeds.

Jan 1, 1986

By R. S. Shoemaker, D. L. Harris

Past investigations into the possibility of concentrating the low-grade iron ores of the Gogebic Range in Wisconsin have been hampered by the complex association of the constituent minerals. In part the problem arises from the fact that the iron occurs essentially as two minerals, hematite and goethite, having nearly the same chemical composition but exhibiting different physical properties. Individual grains of these minerals are usually so small that the ore must be ground to a size finer than 325 mesh if substantial liberation of the minerals is to be secured. Appraisal of beneficiation tests on this iron ore requires, therefore, some method of determining quantitatively the contents of constituent minerals in the various products of the beneficiation. Because of the chemical similarity of the two iron minerals, chemical analyses do not provide a means of differentiation. Although the minerals are different physically, they are both opaque and friable, and as the ore must be ground to a very fine size for liberation to be secured, quantitative microscopic methods of analysis are extremely difficult at best. In an effort to overcome these analytical problems, a quantitative X-ray diffraction analysis method has been developed at the University of Wisconsin for the research program on iron ore beneficiation.

Jan 5, 1955

By Charles J. Haas

The resistance which rock bolts offer to shear movements along fracture planes and bedding planes near a mine opening has been suggested as one of the mechanisms by which bolts contribute to the support of weak rock in the roof or sidewall. That such displacements do occur is a fact fairly well known. Inspections of drill holes that have been drilled for some time often reveal that the holes have been offset at one or more points some time after drilling. Resin grouted bolts are often cited as being better able to resist shear movement in the roof because the annulus around the steel bar is filled with grout, whereas the sides of a conventional bolt will not contact the rock until a rather large shear displacement has occurred. When this project began, there were no experimental data to support or refute the above arguments. A laboratory shear test program was, therefore, devised to evaluate the effectiveness of various types of bolts in resisting shear under various conditions which exist in situ. Research reported earlier (Haas, 1976) included a theoretical analysis of a conventional bolt intersecting a shear surface, and experimental data on the shear resistance of smooth (lapped) shear surfaces, intersected at various angles by conventional and resin grouted bolts. The present paper extends the previous analysis to consider the effect of the initial roughness of the shear surface. Joint roughness is a particularly significant factor since undulations of the shear surface cause dilatation of the joint, which in turn, causes high tensile loading of a bolt intersecting the joint.

Jan 1, 1982

By G. Sachs, G. Espey

SIMPLE methods can be used for the determination of the residual stresses in thin-walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface Such a stress distribution is approximated in sunk tubing and in deep-drawn shells It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the part that is separated from the adjacent metal The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig Ib),1-5 or from deflection resulting from the cutting out of a circumferential tongue (Fig Ia) G The bending moment M released by such a flexure is [ ] The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (zx from the surface [ ] where C is the section modulus and d is the thickness of the section, the ratio AI C being d 2 for a rectangular section* The maximum stress values at the surfaces are [ ] For most purposes the simpler equations [ ] will be satisfactory, where Dm is the average of the mean diameters of the tubing

Jan 1, 1941

By S. C. Riemer, I. Iwasaki, J. N. Orlich

The effects of percent solids, mill loading, and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of - 44-µm (- 325-mesh) material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that corrosive wear was mini- mal under nitrogen flushing conditions, and that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition. Pulp viscosity controlled the thickness of pulp layer on balls, thereby affecting grinding efficiency and ball wear.

Jan 1, 1986

By J. M. Bugbee

THE engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance.

Jan 1, 1942

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

Jan 7, 1951

By P. A. Robbins

FAR NORTH, on the bare Arctic tundra, 11 mi. above the mouth of the Keewalik River where the latter discharges into Kotzebue Sound. several ., Eskimos garbed in parkies and muck lucks mingle with a small group of similarly clad white men. All of them shield their eyes from the white glare of the arc as a gasoline-driven arc-welding set rains molecules of metal on the break in a bull wheel, the large gear wheel which swings the boom and cab of a dragline shovel.

Jan 1, 1937

By AIME AIME

L. C. GRATON, professor of geology in Harvard University, addressed the New York Section on April 24 on-his impressions of the Rand. His beautifully clear and concise address was delivered without notes, so that what follows is merely a resume of the principal points made. The world is apparently coming to the end of ore discoveries easily made, yet we need metals at a steadily increasing rate. If surface discoveries are to decline, then we must find other ores or use less metals. The probable chances of finding ore are greater in the centers of big production than in new districts, as proved statistically. It is unsafe to say that a field is worked out. Therefore, deep mining holds possibilities and is an interesting study that will progressively gain in importance. The origin of the gold in the banket of the Rand has been a geologic football for a long time. Of the various theories, two have survived: 1. Infiltration into permeable conglomerate beds from deep-seated sources; 2. the placer hypothesis, which holds that gravel beds originally had the gold in them. At present, the second theory is accepted by the majority, as a result of the studies by the Union Geological Survey and by E: F. Mellor which were published about fifteen years ago.

Jan 1, 1929

By K. W. Smith, E. A. Thomas

Various grades of synthetic mullite have been developed in recent years to replace or supplement natural sources of mullite deriued from the mullite group of minerals consisting of sillimanite, kyanite, and andalusite. Raw materials and heat treating processes used in making synthetic mullite are described. Chemical and physical data are given for typical grades and crystalline structure is illustrated with micrographs. Use of synthetic mullite as a refractory material in the glass and metallurgical industries is discussed. Mullite (3A12O3.2siO2), the only stable compound formed in the alumina-silica system, is usually present to some degree in all aluminum silicate ceramic products. The formation of mullite is considered beneficial to give rigidity to the structure and is dependent upon the ratio of Al2O3 to SiO2 in the original composition, particle size, degree of mixing, firing temperature, cooling rate, and the presence of auxiliary glass-forming fluxes. Mullite may also be formed at the reaction interface of fire clay or alumina-type refractories in contact with glass or slag melts. The term synthetic mullite is commonly used today to identify a class of sintered and fused aggregates or grains in the alumina-silica system having a highly developed mullite structure but derived mainly from raw materials other than the sillimanite group of minerals. Within the past 15 years extensive research has been done to develop economical processes to form sintered synthetic mullite aggregate to replace calcined Indian kyanite in super-refractories. Severa1 brands of such mullite are now being produced in commerical quantity and finding extensive use in refractories. Based on the service results of such refractories in many applications throughout the metallurgical, ceramic, and glass industry these developments have been considered successful and suitable substitutes for Indian kyanite now appear assured. EARLY DEVELOPMENT The conversion of kyanite, sillimanite and anda-lusite minerals of the sillimanite group to mullite and their use in refractories and porcelain have been discussed quite extensively in the literature by peck,' Grieg,' Riddle and Foster,3 Bowen and Grieg,4 and others and will only be mentioned here for reference to compare properties with synthetic mullite. In 1928, curtis5 reported on the development of a high temperature gas-converter process for forming synthetic mullite. The raw materials were derived mainly from lumps of high alumina clay of the correct natural composition or blends of clays and alumina that was interground and briquetted to form a suitable charge to maintain a surface combustion firing within the converter. Curtis was, no doubt, the first to illustrate by micrographs in natural color the crystalline structure of mullite derived from kyanite and mullite derived by sintering clay and alumina mixtures at temperatures above cone 32 (3123°F) and by electric fusion. In 1937, sei16 was issued a patent covering the use of a mixture of alumina-silica minerals and alumina in the proportion to form a mullite-yielding material at temperatures in excess of 3100' F. During the period from 1930 to 1940, economic conditions were not favorable for the production of synthetic mullite mainly due to an adequate supply of good grades of Indian kyanite ore suitable for conversion to mullite. Uncertain conditions on availability of the Indian kyanite during the early stages of World War II fostered further study on the development of synthetic substitutes. In 1943, McVay and wilson7 reported on an extensive investigation of domestic substitute materials. Their work covered essentially the use of mixtures of electric furnace mullite, calcined topaz, and calcined domestic kyanite. Compositions were found that gave equivalent or better hot load strength than Indian kyanite in mullite-type brick compositions; however, the calcining of the topaz presented certain physical and chemical problems on the disposition of silicofluoride and hydrofluoric acid while the high cost of electric furnace mullite was a limiting factor. In this work it was pointed out that water-quenched fused mullite was found to be unstable on reheat and gave poor hot load strength due to excessive glass present whereas the slow cooled or annealed mullite contained large crystals of mullite and corundum with little glass and gave superior results.

Jan 1, 1961

By K. W. Nelson, John N. Abersold

INDUSTRIAL hygiene has been defined by Patty' as "the science and art of recognizing, evaluating, and controlling potentially harmful factors in the industrial environment." This definition implies thorough study of operations, evaluation of potentially harmful factors through air sampling, micro-analyses and other means and finally, appropriate medical and engineering control wherever indicated. The prevention of industrial health injuries is a vital part of operations of American industry today. Progress and interest in this field has increased steadily for many years, the most rapid progress having been attained, perhaps, during the last three decades. It is significant to note that there are now official agencies in 46 states actively concerned with industrial health problems and that a western field station has been established recently in Salt Lake City by the U. S. Public Health Service to augment its industrial hygiene services directed from headquarters of the National Institute of Health, Bethesda, Md. Many of the larger industries have found it advantageous to establish their own industrial hygiene departments. The American Smelting and Refining Co. is a world-wide organization engaged in the mining, smelting, and refining of lead, copper, zinc, silver, gold, by-product metals, including cadmium, arsenic, and others. In the United States there are 13 smelters and refineries, 11 secondary smelters or foundries, and a number of mines. Approximately 9000 workers are normally employed. It has long been the established company policy to seek out occupational hazards and provide safeguards for employee health. Protective equipment has been supplied to individual workers and exhaust ventilation installations have been in use in some operations for more than 40 years. All of the major units have their own medical departments which provide employees with excellent medical and hospital care. In 1937 full scale industrial hygiene studies were undertaken at the Selby Plant and were extended to most of the other smelters during the next three years. In 1945 the Department of Hygiene was organized with Professor Philip Drinker of Harvard University as Director and with Dr. S. S. Pinto as Medical Director. The department is responsible for coordinating and maintaining a program for the good health of all employees from top management down to the lowest paid day worker. It is essentially a service organization serving all of the United States plants regardless of location or size. Full and part-time physicians employed in all of the company's American plants and working in close cooperation with the Medical Director are responsible for de- termining the state of health of all the employees and giving treatment when necessary. In general, medical care is confined to accidents or illnesses occurring while the men are on the job. Among the duties of the doctors is the making of careful physical examinations of new employees and routine check-ups of old employees. In addition to medical care a primary responsibility of the department is the prevention of occupational illnesses. In this the main concern is with the working environment in relation to its effect on the worker. Environmental factors may be dusts, fumes, gases, toxic materials, heat, humidity, radiation, or noise. The objectives are: (1) Immediate control of these factors through the education of the worker, through providing the wearing of respirators or other protective devices, and through careful medical examinations and regular analysis of urine specimens; (2) a long range control program which may be accomplished by local exhaust ventilation, wetting of materials, changes in metallurgy, changes in methods of handling, or by use of special devices and special equipment. To accomplish these objectives a fine industrial hygiene laboratory was built in Salt Lake City and equipped to do routine and experimental work. Trained and experienced industrial hygienists obtain the facts by making frequent hygiene surveys. These surveys include tests of the air, studies of all processes, and careful investigation of ventilation, lighting, and general working conditions. Except in emergencies, the air contaminants and often the substances handled by the worker are sent to the laboratory for analysis by chemists and technicians specially trained in industrial hygiene methods. The findings are evaluated in terms of limits recommended by various State and Federal agencies, and in light of all available medical data. The methods used for studying the working environment involve all of the usual chemical and physical procedures employed in industrial hygiene. The Impinger, electric precipitator, thermal pre-cipitator, and filter paper sampler have been used to collect atmospheric dust and fume samples. Of special interest here is the filter paper sampler, shown in Fig. 1, which was developed by Dr. Silver-man at Harvard University. The instrument has been improved and is used very extensively in field studies. A water manometer connected behind an orifice is used to determine the rate of air flow. Calibration is effected by use of a standard gas meter or rotameter. The dust or fume is collected on a filter paper clamped between two rings, as shown in Fig. 2. The filter paper, such as Whatman No. 52, collects both dust and fume with a very high efficiency. The instrument is very convenient and easily transported. The solids collected on the filter paper are analyzed in the laboratory usually by use of a polar-ographic procedure. By this procedure it is possible to measure quantitatively in a single analysis the

Jan 1, 1952

By J Price, M. R. Geer, H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others. Hardgrove' stated that maintenance costs entailed by the wear of grinding elements is often a more important variable than the cost of the power required to pulverize different coals. Craig2 also reports that one coal may cause pulverizer parts to wear several times faster than another. It is apparent, therefore, that those concerned with pulverizing coal could profitably employ a method for estimating the abrasiveness of different coals, just as they utilize standard tests for thermal value, grindability, and ash-fusion temperature to assist in selecting the most suitable and economical coal to use in a particular plant. The objective of this investigation was to develop a test procedure that would be suitable for general use in estimating the abrasiveness of coals. However, few, if any, of the standard tests now used for evaluating the properties of coal are the product of a single investigation or the result of a single investigator's efforts. Rather, in each case, a testing procedure was devised by one investigator, used by others on a wider variety of coals, and finally refined completely as the result of the joint efforts of a number of interested people. Thus, the test procedure for estimating abrasiveness developed in the course of this work may not be refined sufficiently in its present form for general use, but it may serve as the starting point from which an acceptable test procedure can be developed. The method has been used thus far on only about a dozen coals, and there has been no opportunity to attempt a correlation between experimental results and actual plant experience. Only wider use of the procedure by other investigators and correlation with plant experience can determine to what extent the method will have to be modified to render it suitable for general application. Test Method Although the literature contains no record of an attempt to devise a method for estimating the abrasiveness of coal that could be used industrially, several investigators have tested properties of coal that are closely related to its abrasiveness. The abrasiveness of a material generally is considered to be related to its hardness, and hardness tests for coal have been employed by Heywood,' O'Neill," and Mathes. Also, the resistance of coal to abrasion, a property that presumably is related to the abrasiveness of coal, was measured by Heywooda and by Simek, Pulkrabek, and Coufalik.2 11 these investigators tested only individual pieces of coal. Since coal is a heterogeneous material having components of varying properties, tests of this type can yield results having little more than academic interest. Only a test method that utilizes a representative sample of coal can give results that are useful industrially. The abrasion tests used for various other materials have been considered for adaptation to testing the abrasiveness of coal. The tests used for metals,7-9 paving and flooring,'" and rubber," cannot be used because coal is not sufficiently abrasive.~ The present experimental work was begun before World War II and was conducted by three research fellows"'" working under a joint agreement between the University of Washington and the Bureau of Mines. After a great deal of preliminary work with a variety of apparatus and materials, a test procedure was developed which consisted of rotating a test disk 2Yz in. diam in a steel mortar containing the coal sample. The shaft carrying the test disk at the lower end and a 100-lb load on the upper end was free to move vertically. The bed of coal in the mortar was kept fluid by low-pressure air admitted through a port near the bottom of the mortar. Measurable wear on an Armco iron disk could be obtained in this test procedure, but, despite extensive efforts to eliminate them, several major disadvantages remained in this test method. First, with most coals the amount of wear on the iron disk did not exceed a few milligrams. Second, a single type of disk was not applicable for all coals. A smooth iron disk gave satisfactory results with both bituminous and sub-bituminous coals, but hardly any wear with anthracite or coke. A disk having studs or projections gave more satisfactory abrasion losses with anthracite and coke and presented no operating difficulties with free-burning bituminous and sub-bituminous coals. It could not, however, be used with caking coals because these coals formed a

Jan 1, 1952

By AIME AIME

THE difficult problem of visitors is being met by the Hudson Coal Co. at Scranton in an ingenious fashion. The Company had long made it a point to have dealers selling its coal visit the mines, whenever possible. "The excellent reaction obtained from these dealer visits brought up the question of whether it would not be possible to open one or more mines to the public, and give the consumer an opportunity of seeing for himself how anthracite is mined and prepared. Ac-

Jan 1, 1929

By A. B. Kinzel

IT has often been stated that the steel industry did no research or development work in the decades preceding 1920. If restricted to organized research on the quality and field of application of structural and engineering steels, this statement may be true. But the industry did conduct a vast amount of process research during this period, although some of the projects were not carried out as separate organized research programs. Securing a low cost of tonnage production was the sole problem receiving serious attention from the industry prior to 1920, and today this is still the major problem. Those in the industry deserve much commendation for the important increase in production capacity per dollar invested and for the markedly lowered cost of production. In recent years, a distinct change may be noted in the attitude of the steel industry toward research involving its product. With the advent of high-speed machinery both in the manufacturing and transportation industries, steel as a quality engineering material has come to the fore. In the past, high-quality carbon steels and alloy steels have been introduced over a period of years, largely at the insistence of the consumer and partly prompted by research carried out by those interested in the use of the alloys. The commercial introduction of these materials made slow progress.

Jan 1, 1935

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks' show in 1938 so that more time will be avail-

Jan 1, 1936

By Carl H. Samans

In their recent complete review of the subject of age-hardening,' R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers ('discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By Zay Jeffries

IT is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a. fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a fine-grained steel rail might have grains or cells 100 times larger than coarse-grained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable than the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of. metal for a specific use, the latter determination being more indicative of. the life of the metal part than the tensile test. A grain-size determination with a tensile test is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now.

Jan 12, 1915

By Francis Foley

FROM the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.1 They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration. of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Westgren and Phragmèn3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 10, 1925