Search Documents

By J. A. Herbst, D. W. Fuerstenau

The effect of mill speed and ball load on the dry ball milling of dolomite is examined in the context of the batch grinding model. Observed changes in the parameters of the model are interpreted, as far as possible, in terms of the mechanics of particle motion in the mill. A parameter estimation scheme previously proposed by the authors is shown to provide the basis for a successful simulation of grinding behavior over a wide range of mill speeds and ball loads. Finally, a combination of experimental and simulated results is used to determine the optimum mill speedball load for closed circuit grinding in this mill-material system.

Jan 1, 1973

By R. C. Croft

Many chemical methods of upgrading ilmenite to enhance its titanium dioxide content involve reduction of the FeO in this mineral followed by solution of the metallic iron produced. While the use of most mineral acids for this purpose entails acid regeneration or salt disposal problems, these difficulties can be overcome with carbonic acid. Satisfactory rates of iron removal have been achieved at temperatures below 100° C and at CO, pressures up to 600 psi. Lowering of gas pressure over soluble bicarbonate solutions permits recovery of CO. and precipitation of iron oxide. The removal of the manganese, often present in ilmenites, is also feasible with these treatments.

Jan 1, 1972

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

Held at San Francisco, Cal., Thursday to Sunday, Sept. 16 to 19, 1915 COMMITTEES Arrangements CHARLES W. MERRILL, Chairman EDWARD H. BENJAMIIN H. C. HOOVER FRED `V. BRADLEY W. C. RALSTON ABBOT A. HANKS G. H. CLEVENGER Excursion and Accommodations ABBOT A. HANKS, Chairman E. T. BLAKE R. H. BEDFORD C. G. DENNIS FREDERICK BRADSHAW C. E. GRUNSKY, JR. EDMUND JUESSEN ARTHUR B. FOOTE F. A. KEITH GEORGE 0. BRADLEY CHARLES JANIN E. N. ENGELHARDT R. S. HASELTINE N. CLEAVELAND

Jan 12, 1915

By S. A. Braley

DRAINAGE of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned. It is well to consider some of the many procedures that have been used to determine the composition

Jan 1, 1957

By Gordon C. Rausser, Michael D. Boehlje, Richard A. Levins, John A. Otte

Changes in SO2 emission standards will not only influence the cost of supplying energy demands from coal, but also the competitive position of various production regions and the method of mining (surface vs. underground). A multiperiod interregional competition model was utilized to evaluate the interactions between mining capacity, new mine development, coal reserves, mining, processing and transportation costs and equipment availability and SO2 emission standards. The empirical results indicate that not only will costs increase dramatically, but production in eastern as well as western regions that have low sulfur reserves will also increase as sulfur standards become increasingly more strict. Implications of the adjustments in the location of coal mining activity for the processing, transportation, and capital goods markets are also presented.

Jan 1, 1978

By M. R. Stauffer, Z. Hajnal

Seismic velocity determinations over Precambrian outcrops near Flin Flon, Manitoba, indicate that several different rock types have sufficient velocity contrast to make reflection mapping possible. Stratigraphic and fault contacts between metasedimentary and metavolcanic rocks have been mapped at some depth. A mu1ti-fold reflection survey attempted to trace the depth extension of an ore-bearing (Pb-Zn) rhyolite horizon within the metavolcanic rocks. A synthetic seismogram has been produced from a 10,000-ft sonic log and provides means of comparing seismic records with the local geology. From this the optimum frequency spectrum and the maximum resolution of the seismic signals were estimated.

Jan 1, 1978

By Robert A. Campbell, Robert J. Brison

The problem of optimizing from an economic standpoint the capacity of grinding equipment in the design of a new concentrator is discussed. Although directed specifically to copper flotation mills employing conventional wet, grinding, the material presented is considered applicable with modifications to other types of ores and other grinding methods. A general approach to optimizing the grinding capacity is outlined and illustrated by an example. The' interrelation between grinding capacity and other aspects of the project is considered. The problem of regrind capacity and its relation to preceeding and subsequent processing steps is also discussed. Finally, factors are considered that may, in certain cases, dictate modifications of the suggested approach.

Jan 1, 1974

By J. O. Whiteley

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By R. McEwen, G. W. Hansen, G. F. Lee

The effect of using an anionic collector, Reagent 308, a sodium petroleum sulfonate, with a cationic collector, Armac T, a tallow, fatty acid amine acetate, was studied in a series of monomineralic flotation trials with the alkali feldspars and heavy minerals, ilmenite, rutile, garnet, and monazite. This combination of cationic and anionic collectors is employed to float feldspar and heavy minerals from quartz in the beneficiation of sand in Normanville, South Australia, to produce a suitable quartz sand for glassmaking. In the alkali feldspar trials, Armac T additions were held constant, while the 308 additions were varied. In the heavy mineral trials, the 308 was held constant while the Armac T was varied. Peak enhancement of the feldspar recovery was noted when the 308 additions were between 25% and 150% that of the Armac T additions. At higher 308 addition, depression of feldspar flotation occurred. This appears to be due to a neutralizing effect in the combined collector system and to the formation of a nondissociating complex of both collectors. This variability in flotation response when Armac T is used with 308 suggests that the two collectors do not act independently of each other.

Jan 1, 1977

By Theodore H. Eyde

The porphyry-copper province of southwestern United States and northern Mexico constitutes the largest copper-producing region in the world. More than 20 deposits discovered since World War II are being exploited or in the process of exploration and development. Because of the remarkable success in discovering new deposits, exploration activity continues at a very high rate and deeper targets are explored each year. Exploration programs for deeply buried porphyry-copper deposits require a reevaluation of the conventional exploration techniques. Though surface induced-polarization techniques have about reached their practical detection limit, aeromagnetics will play an increasing role in the exploration activity as will downhole logging tools. In addition to a valid geological concept, any successful exploration program for porphyry-copper deposits in the southwest must have two other essential ingredients: money and guts. Unfortunately many exploration programs in the southwest are underfunded and doomed to failure. Future exploration will demand more joint venturing in which larger and more expensive exploration programs can be successfully funded by groups of companies or syndicates.

Jan 1, 1975

By Terry E. Perkins, Len Marnewecke

Installation of a relatively simple, low-cost analog mill control system at Amax Lead Co. of Missouri's Buick concentrator has paid off handsomely. The system, which provides the capability of handling mill circuit upsets and ore changes while maintaining a desired particle size, is expected to generate annually a return on investment of several times its capital cost. In addition, the system stresses simplicity of field instrumentation and control strategy, leading to better operator acceptance and understanding, and its capital cost makes it very attractive for the specific installation when compared to more complex schemes using mass flow measurement and computers for calculating circulating load to infer particle size. This system has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value.

Jan 2, 1978

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By Jerry M. Thornton, Richard W. Cannon, Don C. Rotherham

This paper attempts to show the role of induced polarization (IP) and resistivity surveys in the discovery of the ore bodies of Gibraltar Mines Ltd. (N.P.L.) and the importance of conducting large enough surveys to properly evaluate the results. The first IP survey was conducted in the area in 1963. This survey was extended and other IP surveys were added to it for the next seven years. The data from these surveys was finally combined to produce four large scale plan maps of resistivity and percent frequency effect (PFE) results (N = 1 and 3). A halo-type anomalous zone 6000 ft wide and 14,000 ft long was thus outlined in the PFE maps. The four ore bodies of Gibraltar Mines were found to occur along the inside rim of this IP halo.

Jan 1, 1973

By F. Rosenblum, P. Spira, F. Kitzinger

The possibility of increasing the efficiency of mineral processing plants by means of computer control has prompted metallurgists to examine their flowsheets more critically in order to develop practical control strategies. Control schemes in use to date generally rely on the automation of traditional and previously manually regulated control loops, e.g., the addition of reagents to maintain a constant assay or a constant pH. This approach is predicated on the availability of well established primary sensors such as pH electrodes or on-stream analyzers. Noranda Research Center, in cooperation with Noranda Group concentrators, has developed a froth level monitor and a pulp density meter adaptable to this type of control. Although some of the basic principles on which they are based have been known for some time, their incorporation into the design of reliable, direct-reading instruments which can be interfaced with a computer is believed to be novel.

Jan 1, 1980

By CARL B. SNYDER

PERHAPS the most extraordinary thing about business, the trade and production of the country as a whole, is its amazing continuity and growth, its momentum and energy. It goes on year after year, growing steadily, almost without breaks, in spite of every kind of disturbance. We have been grossly deceived into the idea that business is highly variable. We have taken a few things like pig iron, and the like, constructional activity broadly, and imagined that these are a trustworthy measure of trade. Actually they are the worst that we could find. They do not apply to more than 10 per cent or, at the most, possibly 15 per cent of the total of the country's industrial activity. The other 85 or 90 per cent, or even more, goes on growing surely and steadily just like the growth of population and the steady advance in technique, invention, discovery, and improved methods of production Let me give you what seems to me one of the most remarkable examples of this amazing momentum and regularity. You know that 90 per cent or more of the business of the country is done 'by means of checks. About seven-eighths of the total of all checks drawn are reported regularly every week in the newspapers. Let us follow these reports from week to week, just as they come, and plot them up against the correspond- ing weeks of last year, and the year before, and the gear before that, as far back as you would like to go. Take especially the figures for 140 selected cities out- side of New York.

Jan 1, 1929

By D. A. Schemnitz, O. W. Ellis

Certain alloys1 that, as a result of quenching, are retained in the form of homoaeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys2 that, on rapid cooling, are held in the form of homogeneous solid solution, as, for example, certain steels, behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as " aging"' or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 1, 1925

By H. J. French

AT THE request of a committee of the Engineering Division,1 National Research Council, a study of the properties of boiler plate at various temperatures up to about 900° F. (482° C.) has been instigated. The following is a report of preliminary tests made on two grades of ½ -in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions.

Jan 2, 1920

By AIME AIME

MINING geology has been at once the vocation and avocation of John M. Boutwell, newly elected Director of the Institute representing Utah and Colorado. Geologists were looked at askance by most of the "big" men in mining when, from 1896 to 1900. Mr. Boutwell was teaching geology at Harvard, his alma neater; and his success in applying geologic principles to the business of finding ore contributed much to changing the attitude of scepticism. From 1900 to 1908 lie was with the U. S. Geological Survey, with service in Bingham, Utah; Morenci, Ariz.; and Park City, Utah. Since then he has been engaged in private practice as a consulting mining geologist retained by many of the leading mining companies. A dozen men now recognized as outstanding geologists got their early

Jan 1, 1937

By George H. Ashley

It has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. Production and Value In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately. Pennsylvania Accurate figures are obtainable for Pennsylvania for recent years because recent reports of the Pellnsylvania Department of Mines show the production from each mine and the bed worked at each mine. For recent years, therefore, it is only necessary to list the mines working in the Pittsburgh bed and add up their production. The value was obtained by treating each county separately, applying the average price for the county to the production of Pittsburgh coal in that county. Unfortunately for great accuracy, while production figures for individual mines are available for many years, the name of the bed being

Jan 1, 1938