Search Documents

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By Richard P. Schoemaker

INTRODUCTION IN underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to inhomogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. THE PRESSURE DOME THEORY The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1947

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

By M. K. Geer, H. F. Yancey

Investigations of the fundamental factors involved in the performance of various coal-cleaning processes have constituted a substantial portion of the research 011 coal cleaning conducted by the Bureau of Mines. These detailed studies of the mechanism of separating coal from impurity in various cleaning devices were undertaken to provide the coal industry with information that is helpful in selecting the type of cleaner most suitable for treating a particular coal. Previous reports describing these investigations have dealt with the wet table,1 the pneumatic table,' and the plunger,3 pulsator.4 and Baum types5 of jigs. The present report compares the performance of three commonly used units treating the same coal—a pneumatic jig, also known as the air-flow. cleaner, a pneumatic table, and a Baum-type jig. Object and Plan The fact that pneumatic coal-cleaning processes are less efficient than wet-washing methods because they are unable to make as sharp a separation between coal and impurity is well recogilized. The literature, however, contains little quantitative in- formation on the relative performances of the two types of cleaners. The object of the present report is to present a detailed comparison of the performances of two pneumatic units and one wet-washing process treating coal from the same bed. Although the information in this report demonstrates that the performance of the pneumatic cleaners is not as good as that of those employing water, it must not be construed as reflecting on the usefullless of such equipment. Performance is often secondary to other factors in the selection of coal-cleaning equipment, and the advantages inherent in pneumatic processes frequently outweigh the limitations imposed by their performance. Specific gravity and particle size are the principal factors that influence the separation of coal from impurity in either pneumatic or wet processes; consequently, the tools available for this investigation were the float-and-sink bath and the screen. Accordingly, the raw coal, clean coal, and refuse samples representing the operation of each type of cleaning unit were first separated into a series of density fractions by means of the float-and-sink bath, and then each density fraction was screened into a series of size fractions. By this procedure the raw coal, clean coal, and refuse were subdivided into components of restricted ranges in density and size. From these data it was possible to determine how the cleaning unit disposed of each component of the raw coal; that is. what proportion of each component is sent to clean coal or rejected as refuse.

Jan 1, 1947

By H. F. Yancey, M. K. Geer

Investigations of the fundamental factors involved in the performance of various coal-cleaning processes have constituted a substantial portion of the research 011 coal cleaning conducted by the Bureau of Mines. These detailed studies of the mechanism of separating coal from impurity in various cleaning devices were undertaken to provide the coal industry with information that is helpful in selecting the type of cleaner most suitable for treating a particular coal. Previous reports describing these investigations have dealt with the wet table,1 the pneumatic table,' and the plunger,3 pulsator.4 and Baum types5 of jigs. The present report compares the performance of three commonly used units treating the same coal—a pneumatic jig, also known as the air-flow. cleaner, a pneumatic table, and a Baum-type jig. Object and Plan The fact that pneumatic coal-cleaning processes are less efficient than wet-washing methods because they are unable to make as sharp a separation between coal and impurity is well recogilized. The literature, however, contains little quantitative in- formation on the relative performances of the two types of cleaners. The object of the present report is to present a detailed comparison of the performances of two pneumatic units and one wet-washing process treating coal from the same bed. Although the information in this report demonstrates that the performance of the pneumatic cleaners is not as good as that of those employing water, it must not be construed as reflecting on the usefullless of such equipment. Performance is often secondary to other factors in the selection of coal-cleaning equipment, and the advantages inherent in pneumatic processes frequently outweigh the limitations imposed by their performance. Specific gravity and particle size are the principal factors that influence the separation of coal from impurity in either pneumatic or wet processes; consequently, the tools available for this investigation were the float-and-sink bath and the screen. Accordingly, the raw coal, clean coal, and refuse samples representing the operation of each type of cleaning unit were first separated into a series of density fractions by means of the float-and-sink bath, and then each density fraction was screened into a series of size fractions. By this procedure the raw coal, clean coal, and refuse were subdivided into components of restricted ranges in density and size. From these data it was possible to determine how the cleaning unit disposed of each component of the raw coal; that is. what proportion of each component is sent to clean coal or rejected as refuse.

Jan 1, 1947

By A. H. Lindley, R. Shorr, Frazier M. Stewart, F. Crerie

The mineral industry, so important to industrial development, faces a major challenge in creating the most effective financial structure to provide funds essential for seeking, evaluating, developing, and extracting minerals. The acquisition of funds for mineral development and plant erection do not differ greatly from fund-raising in nonmineral ventures because risks are essentially comparable. High-risk exploration funds, however, are more difficult for the mineral industry to acquire. With the world's ever-increasing appetite for minerals, the internally generated cash of major oil and mining companies cannot be expected solely to maintain the world's mineral supply. The augmented costs, risks, and difficulties of exploration have been shared increasingly by the smaller independent operator and by private and public participation drilling programs within the petroleum industry over the past 30 years. Only recently has the mining industry awakened to the need for utilizing exploration and development funds derived from sources other than established mining and banking circles. Almost from its inception, the oil industry was forced to drill deep holes through overburden without the aid of a mineral "outcropping" which required geological, and in subsequent years, geophysical interpretation. The poorly financed, nontechnical prospector, who depended on a mineral outcrop, was not to play an important role in oil exploration as he did in mining. Because of the high cost of drilling and the demands for technical judgment to locate an exploration drill hole, corporate and sophisticated private funds generally financed oil discoveries. When external funds were subsequently required, these financially sophisticated explorers would turn to the banking community from which came numerous ingenious innovations, taking cognizance of existing tax laws. Like the oil explorer, the miner is now faced with probing below the surface, relying solely on regional geology and geophysical anomalies. The day is gone, for practical purposes, when the prospector discovers a deposit from a mineral outcrop. There is little doubt that the mining industry will now follow the course taken by the petroleum industry in acquiring external funds if it is to meet the future raw material requirements of the world. The oil industry has been able to attract bank funds more readily than the mining industry after a mineral discovery has been made because: (1) with few exceptions, an oil discovery can be placed into commercial production and will generate cash at much less expense and time than a mine; and (2) generally, costs of oil production, the value

Jan 1, 1976

By G. W. Josephson

SINCE the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,1 and the large-scale expansion of the industry has taken place since 1900. HISTORICAL BACKGROUND Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a Nigh degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun's rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof-conservatively, 500 per cent. Slate Granules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate pro-

Jan 1, 1944

By Michael Bradbury

INTRODUCTION A major change in financing exports in recent years has been the decreased importance of subsidized export credits, following the commitment of the OECD countries to eliminate the subsidy element. Subsidized export credit rates are now often more expensive than market rates as the financing for exporters has decreased in volume and importance. The forfait market, in recognition of this decreasing importance, provides a rapidly expanding source of nonrecource finance for exporters. The following is a step by step guide to what it is, how it works, its benefits and problems. WHAT IS FORFAITING? Forfaiting is not new. It has been used in Europe for about 25 years to provide export finance for both capital goods and commodities without recourse to the exporter. Although long the preserve of exporters in Germany, and more lately Italy, forfaiting is now used increasingly by exporters in Great Britain, the United States, Canada and Scandinavia. It is a fairly simple operation with easy straight-forward documentation. The transaction involves the purchase by the forfaiting bank of a bill of exchange or a series of bills without recourse to the exporter. These bills will have been drawn by the exporter, accepted by the importer, and will usually bear the unconditional guarantee of the importer's bank. They are normally drawn payable at intervals during the credit period agreed between importer and exporter and are purchased at a discount by the forfaiter. The exporter thus obtains his cash payment and the importer receives his credit period. The forfaiter collects the amount of the bills as they mature directly from the importer. Credit periods vary, depending upon the type of goods and the country and commercial risk of the importer. The period is generally between one and five years with six monthly maturities. The usual forfait currencies are US dollars. Deutschmarks and Swiss francs and others, such as sterling, French francs, and the Scandinavian currencies are being used more frequently. CHOOSING FORFAITING Most types of financing require the continued involvement of the exporter in the financial side of the transaction during the credit period. Forfaiting has certain comparative advantages. In particular, it is possible to forfait 100 percent of the risk without recourse to the exporter, unlike government sponsored export finance schemes, where some retention of the risk by the exporter is required. In addition, exports from country sources do not present problems and forfaiting can also cover trade within the EEC. Other benefits for the exporter are: (a) The exporter's balance sheet is improved; debts are turned into cash thus improving the liquidity of the company and enhancing its cash flow. And there are no contingent liabilities for bills of exchange. (b) If the sales contract is in a foreign currency forfaiting removes the risk to the exporter of adverse movements in foreign exchange during the credit period. (c) Fluctuations in interest rates during the credit period can be ignored since in forfaiting the transaction is usually done on fixed interest rate terms on a discount basis. (d) The political and transfer risks are taken by the forfaiter. (e) The commercial risk is taken by the forfaiter. (f) The costs of administration and collection etc. during the credit period are removed.

Jan 1, 1985

By J. B. Newkirk

Results of a Debye-Scherrer X-ray investigation are given which show that the order-disorder transformation is a first-order or heterogeneous reaction in Cu-AU alloys with compositions near CuAu. Evidence was found for conventional tie-line segregation across a usual type of two-phase field separating the ordered and disordered fields in the Cu-Au equilibrium phase diagram. The horizontal and vertical widths of the two-phase fields are about 3 atomic pct and 20°C, respectively, at 43 and 54 atomic pct Au. No evidence for the existence of an ordered structure based on a stoichiometric composition of Cu3Au2 could be found. ALTHOUGH the modern theories relating the de-Agree of order of binary alloys to temperature and composition have met with considerable success, the nature of the transformation from the disordered state to the ordered state and vice versa has never been well understood. It has been assumed by some' that this is a second-order transformation, that is, a homogeneous change of state. Others2 hold that the transformation is first-order and that the effects characteristic of heterogeneous phase transformation apply. Since this subject is discussed in detail in a recent paper,' the arguments will not be repeated here. The present paper summarizes an experiment which was designed to distinguish between these two viewpoints for the case of Cu-Au alloys near the composition CuAu. The Cu-Au system is an important one because it furnishes prototype alloys, the behavior of which has formed the basis of much of the present-day order-disorder theory. It has recently been shown- hat in alloys near Cu3Au there is a temperature range within which the ordered and disordered states coexist in equilibrium and are distinguishable as separate phases. Therefore, the transformation must be first-order for these alloys. A similar demonstration for alloys near CuAu, however, has been lacking. Experimental Method Essentially the experiment consisted of equilibrating Cu-Au samples at various temperatures, quenching them in water to retain the high temperature states, and then examining them at room temperature for the coexistence of the ordered and disordered structures. The thermal gradient method of heat treatment- as used because it was important that all temperatures over the transformation range should be represented in the test. Briefly, this method consisted of holding a wire of the desired composition, sealed under vacuum in Pyrex, in a known temperature gradient for a long enough time to allow each part of the wire to assume the crystal structure characteristic of the temperature at which it was held. The temperature gradient was produced by inserting into an ordinary wire-wound cylindrical laboratory furnace, an 18 in. length of 1/8 in. ID ceramic tube which was heavily wrapped with asbestos. The furnace power was controlled by a Tag-liabue Celectray controller and a chromel-alumel thermocouple with the junction located on the heating elements. During the equilibrating treatment the widest variation of temperature within the gradient tube was approximately 4°C at the highest temperature. The temperature at various places within the tube was determined, before inserting

Jan 1, 1954

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By P. Nyul, S. Caplan, M. F. Lamorte, T. Gonda

Therrnal resistance is measured on GaAs laser diodes in the temperature range 77" to 300°K. These data show that typically the thermal resistance increases fifteen times from 77 to 300°K. The increase is attributed to the decrease in thermal conductivity of Gds. Nornzalized thermal-resistance experimental and calculated from published thermal-conductivity data) values are compared and good agreement shown. In many practical applications, it is desirable to obtain high average power output from laser diodes. Average power output is determined in large measure by the external efficiency and thermal resistance of the diode.'-3 The average input power with which a laser diode may be pumped is dependent on the thermal resistance. Thermal resistance has been studied over the temperature range from 77" to 300°K which is usually of interest in practical applications. This correspondence presents data on thermal resistance for GaAs laser diodes and compares them to values calculated from thermal-conductivity data. Junction heating arises from three distinct components: 1) joule heating, 2) nonradiative recombinations, and 3) reabsorption of radiation. In high-threshold lasers, joule heating predominates.4 Typically, the nonradiative recombination is not negligible and contributes significantly to junction heating. The loss caused by reabsorption may be of the order of the joule-heating loss.' The fabrication and the geometry of laser diodes have been described in other publications.5 The data presented were obtained from diodes which were fabricated from the same region of a wafer to minimize differences. Fig. 1 shows four types of heat sinks employed in this study. In types 1 and 2, the laser cavities are alloyed; pressure contacts are employed in types 3 and 4, and indium is plated on the inside faces to improve the intimacy of contact between the diode and the heat sink. The thermal resistance R is defined by the following relationship: where AT is the junction-temperature rise above the heat-sink temperature for the diode power dissipation Pd. For measurement of thermal resistance, a direct current is passed through the junction, in the range from 1 to 50 pct of threshold. The diode is placed in the laser mode by superimposing a current pulse of low-duty cycle on the direct current.3 Junction-temperature rise is obtained from the time-resolved laser spectrum at the leading edge of the current pulse.' Typically, the laser line shift is 2.5A per OK. The resolution employed in these experiments is 0.5A; therefore, the accuracy in the temperature measurement is 0.2K. Typically, the temperature rise is 2" to 20°K. The power dissipation is the difference between the dc power input, and the radiation power exiting the diode. The measurement accuracy is less than 1

Jan 1, 1968

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

By J. S. Marsh

The student of steelmaking is all too well acquainted with the fact that in many instances he must deal with data that in graphical representation exhibit the property most desirable in bird shot. This is scarcely mystifying, since the effort to establish one variable as a function of another is usually hampered by the simultaneous operativeness of two or three other factors that may be important. A large part of arriving at relationships that have the pleasing self-consistency of, say, precise measurements of thermal expansion, consists of determining what factors must be held constant-—an even larger part usually consists of collecting data for which those factors have been so maintained. It is not intended to imply that functional relationships in the physical chemistry of steelmaking are hopelessly obscure; on the contrary, it is merely necessary to be undisturbed by marked deviation of some points from a curve that otherwise makes sense. A reaction mechanism suggested by such a curve may call attention to hitherto unsuspected factors operative in the origin of the deviating points, and thus permit another step to be taken in the direction of fuller understanding. It is proposed, therefore, to suggest several empirical relationships. Even though the approach is not always rigorous, deviations caused by simplifying assumptions appear to be too small to obscure a provisional It has been appreciated for some time that the carbon-oxygen reaction in liquid steel is highly important. For example, Körber et al.,' in introducing a summary of their extensive work on steelmaking reactions, said: "... the far-reaching and truly dominating action of carbon upon the metallurgical reactions will be especially stressed ..." In "Basic Open Hearth Steelmaking"2 (hereafter BOHS, for simplicity), it is accepted repeatedly that the various slag-metal interactions are nearly always controlled by the carbon-oxygen reaction. Before further discussion of this reaction, however, it will be worth while to consider briefly the carbon-oxygen equilibrium. In BOHS (p. 483) it is stated that: When liquid iron is brought into contact with gases containing carbon monoxide it absorhs carbon and oxygen. Conversely the carbon and oxygen in the metal unite to form carbon monoxide which is evolved from the bath during the open-hearth boil or while rimming ingots are solidifying. . . . When the equilibrium pressure is one atmosphere the equilibrium-constant equation simplifies, on the assumption that the activity of each element is equal to its percentage, to a constant which has been so much used that it has acquired a special symbol m. where m = %C X %O

Jan 1, 1945

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

By A. W. Ambrose

The underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of waterin;the base of an oil sand present a very serious problem to an oil company sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas. The purpose of this paper is to outline briefly1 general methods of analyzing oil-field water problems in a producing or in a producing and developing oil field, with a view to suggesting repair work on offending wells. Reference is continually made to producing oil wells; the same general method of procedure, however, should be adopted in a gas field.

Jan 1, 1921

By L. A. Rapoport

This paper is intended as an aid in the perfornzance and interpretation of experimental studies of multi-phase flow in porous tnedia. The mathenmatical formulation of incompressible, two-phase flow phenomena in a three-dimensional porous medium is presented. The resulting equations which account for the effects of gravitational and capillary forces are used to derive general scaling laws permitting accurate representation of water-oil displacement processes by means of experimental flow models. The significance of the scaling laws is examined in the light of the physical concepts of micro-behavior of fluids in porous media. Formulations of scaling con(litions obtained by application of dimensional analysis are reviewed. The principles of application and the limitations of flow model studies are discussed. INTRODUCTION Most of the problems facing a reservoir engineer involve three-dimensional, two-phase flow systems. influenced by the effects of gravitational and capillary forces. Present computational procedures generally do not permit the evaluation of such systems without introducing greatly simplifying assumptions. The actual reservoir configuration is usually replaced by one or a combination of several "equivalent" linear systems, and the effects of capillarity and gravity are considered to be negligible. While these assumptions may in many instances be justified, there are a number of important practical problems for which the results obtained on the basis of such simplifications remain open to question. An alternate approach to the problems that are not amenable to analytical treatment consists of seeking their solution by experimental laboratory investigations. The main difficulty of such investigations lies in the fact that multiphase flow phenomena subjected to gravity and capillary forces proceed differently at different rates and in systems of different dimensions. Therefore, unless great discrimination is exercised in selecting the conditions and interpreting the results of laboratory tests, such tests may be entirely misleading in regard to field applications. The purpose of this paper is to present a theoretical background for the performance of laboratory tests that are more nearly representative of field behavior. It will be shown that simulation of field behavior can be achieved by conducting laboratory tests under conditions selected in accordance with definite scaling laws. The formulation of conditions required for the scaling of two-phase flow experiments in porous media has been presented in the literature on several occasions.12,3,4 One of these formulations advanced by Leverett1, cannot be considered applicable to most practical cases inasmuch as it does not cover generally the regime of laminar flow. An adequate treatment, based on the consideration of dimensional analysis, was presented by Engelberts and Klinkenberg.2 Their treatment, however, is concerned primarily with the scaling of linear flow systems, and hence somewhat limited in scope. Accordingly, the formulation of more general scaling laws, applicable to three-dimensional systems, appeared to be warranted. It appeared, furthermore. desirable to establish this formulation on the basis of a mathematical treatment, rather than by application of general principles of dimensional analysis, to permit more explicit

Jan 1, 1956

By W. A. Ver Wiebe, E. G. Dahlgren

The year 1937 must be considered the most eventful one ever experienced in the development of oil and gas activity. Out of a total of 57 new pools discovered, 18 are apportioned to eastern Kansas and 39 to western Kansas. (For statistical purposes Kansas is divided along the meridian that separates ranges 3 E. and 4 E.) In addition to numerous longdistance extensions of the large Hugoton gas field of southwestern Kansas, two other gas pools were discovered in the area lying west of range 3 E. The 37 new oil pools in that area are to be found in 13 different counties, among which Rice heads the list with a total of seven oil pools and one gas pool. Ellis and Barton Counties both added six new oil pools, while Russell County follows in fourth place with four. Among eastern counties Butler heads the list with four new pools. Cowley arid Chautauqua each accounted for three new discoveries. The number of wells necessary to accomplish this result totals 2657, of which 1915 are oil wells and 128 gas wells. The initial production of the oil wells amounted to 2½ million barrels. Although most of the wells were drilled in proven territory, there was a good deal of wildcatting. The fact that 614 dry holes were completed emphasizes the ever-present risk attendant upon the efforts of pioneers. Some of the more venturesome spirits reached out to the counties farthest west in the state. An indication of the feverish excitement reached at times is recorded in the fact that no less than 600 drilling operations were in progress during one week in May, or the fact that over 100 new locations were staked during the second week in July. During one week in May, 65 successful oil wells were completed for an initial production of 68,000 barrels. Many drilling obligations came due during the year, and this perhaps accounts for the fact that one company had as many as 59 active operations at one time during September. Another evidence of great interest in oil possibilities in Kansas is furnished by the record of sales of oil properties, which in one case reached the high figure of about $3000 per acre.

Jan 1, 1938

By David White

IN these days, when detailed investigations of stratigraphy, structure, and sand conditions so frequently result in the discovery of new oil fields, and applause from oil companies and the public, geologists do well to walk humbly, and punctiliously to admit that the geologic principles controlling the distribution of oil and gas have as yet been discovered only in part, and that what remains yet to be learned is probably vastly more than what is already known. The few experiments already at-tempted have been fragmentary, and somewhat desultory, and however positive each of us may be with respect to certain theoretical conclusions, many of the fundamental questions as to the origin and mode of occurrence of petroleum are subject to radical disagreement. Of the chemical changes attending the generation of petroleum from organic matter, little is actually known. Most of the postulated formulas are liable to be misleading, through ignorance of essential factors. Open-mindedness is therefore a prime essential at the present stage of our science. Nevertheless, adopting the hypothesis that oil originates in some manner fundamentally connected with the organic theory, and in possible departure from such open-mindedness, the writer will pay no attention to the so-called inorganic theory, since every attempt to apply this theory to the study of old oil fields, or to the discovery of new ones, affords cumulative evidence of its inadequacy. In this paper, some of the factors affecting the occurrence of petroleum that the writer believes worthy of consideration by the prospector for oil in any new region will be discussed. Some of these, which are less generally understood, will be considered somewhat in detail. Other points, the significance of which cannot now be determined, require more field study, and for that reason are here brought to the attention of the field geologist. On the other hand, certain theoretical points which do not bear especially on the oil possibilities of a new region will be given little

Jan 2, 1920