Search Documents

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of the distribution of nodules on the seafloor and the location of economically important areas, but less effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic processes. It is not by coincidence, however, that the area considered to be most economically feasible is, in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are related indirectly, and possibly directly, to the activities of organisms.

Jan 1, 1983

By D. J. Crouse, W. D. Arnold

The potential behavior of radionuclides released in an underground nuclear detonation to fracture copper ore for subsequent in-situ leaching and copper recovery was studied with regard to contamination of the copper product and hazards to operating personnel. The laboratory test results indicate that only small fractions of the radioactive fission products would be dissolved on leaching the ore. Tritium (as tritiated water) would be the dominant radionuclide in the circulating leach liquor, assuming use of a fusion explosive. The test results showed solvent extraction to have important advantages over cementation for recovering copper from the leach liquors. While the radioactivity of the copper metal product produced by either method should be extremely low, the solvent extraction process provides a more effective separation of copper from the radioactive contaminants and entails fewer radiation protection problems. For these reasons it is the preferred process.

Jan 1, 1976

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silic-ates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 1, 1960

By Francis B. Foley

THE casting of steel in large molds brings into play all of the undesirable effects that result inevitably from slow cooling. The origin of the molten metal, whether basic or acid open hearth or electric furnace, has little if anything to do with the phenomena involved. If the quantity of molten metal to be cast in a single mold is large enough, there is very little one can do about it-the metal will cool so slowly that 'nothing one can do, other than to provide as good feeding as practicable from an adequate reservoir of metal in the sink head, will be of any avail. Recently we have had occasion to cast a 108-in. octagon ingot weighing 545,700 lb, necessitating the combining of metal from three 100-ton open-hearth heats. This is one of the largest ingots ever made. The body of the ingot weighed 448,800 lb, which includes a bottom pool of about 7500 lb of metal, and the sink-head weight was 96,900 lb, or about 18 pct of the total weight.

Jan 1, 1947

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

ThE solubility of carbon in tantalum has been reported to be very low at temperatures below 1500 C,1'2 increasing to at least 0.02 wt pctl at the eutectic temperature of 2800°C. The solubility limits at low temperatures were based on metallo-

Jan 1, 1963

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 x 10[9] cu yd (1.4 X 10[9] m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 X 10[6] cu yd (19 X 10[6] m3) annually.

Jan 11, 1979

By C. R. Pelley

Abstract-This paper describes the analytical characteristics of Western subbituminous coal and the manner in which these characteristics apply to their use in a utility-sized steam generator. It compares these characteristics with those of typical Midwestern coal and Eastern bituminous coal. The paper also reviews in detail the design considerations that must receive attention when various blends of these three coals, or any combinations thereof, are planned to be used. This research paper describes variations in analytical and utilization characteristics when coals from different origins are blended in order to achieve a predetermined sulfur content for the purpose of predicting sulfur oxides emissions as they affect environmental regulations and the resulting alterations in utilization characteristics such blending would cause, and how such blends of coal would affect a utility-sized steam generator.

Jan 1, 1978

By Bennett Bates

NOWHERE in the world has cone classification in closed-circuit grinding with tube mills reached as high a state of development as on the Witwatersrand. In the development of the Far East section the necessity of fine grinding to obtain. satisfactory residues gave rise to a situation with which the cone could cope only at a great sacrifice in efficiency of tube-mill grinding. H., A. White1 recognized the limitation of the cone in his study of the theory of tube milling as early as 1915, but it was not until Ewing, Davis and. Willey2 carried out their tests at Springs Mines during 1920 that the advantages of mechanical classifiers' were demonstrated. During the fall of 1924 the writer supervised a series of tests with Dorr classifiers undertaken by Mr. White, Consulting Metallurgist, at the mill of the Geduld Proprietary Mines, Ltd., Dersley, Transvaal (Far East Rand). The importance of classification to obtain efficient tube-mill grinding was thoroughly demonstrated. The installation of classifiers of the above type that followed the test, confirmed the results of the experimental work.

Jan 2, 1926

By Carleton Ellis

The problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific standpoint, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London ; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by may of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of

Jan 1, 1913

By J. H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the pH range 8 to 11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction that may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as observed with the Wyoming bentonite. Results indicate the conditions that should be met with respect to pH control to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1985

By R. W. Prouty

THE methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz., fall into two divisions because of the difference in occurrence, manner of prospecting, and methods of mining: that for the underground operations and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three classes: Replacements of limestone, replace-ments of porphyry, and replacements of contact breccia The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies it is exceedingly difficult, without sampling, to deter-mine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft. As some of the ore-bodies have a thickness of from 100 to 300 ft., it can be seen that the smaller ones form a difficult problem both in prospecting and in estimating.

Jan 11, 1922

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980

By V. Lessels, W. A. Hamilton

White Pine Copper Co. is a wholly owned subsidiary of the Copper Range Co. The property of White Pine is about 5 miles south of Lake Superior in Carp Lake Township, Ontonagon County, Mich. The new town of White Pine, adjacent to the company plant, is 18 miles south and west of the town of Ontonagon, and about 55 miles north and east of Ironwood, Mich. A diamond drilling program begun in 1937 to develop the orebody was carried on until 1950. During this period a test shaft, known as the Schacht shaft, was sunk on the orebody and approximately 8000 ft of development drift were driven. In an effort to solve the ore beneficiation problems, considerable metallurgical test work was done on ore extracted through the mine development. This work was conducted in a small pilot plant located in the mill of the Copper Range Co. at Freda, Mich.

May 1, 1956

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one bill ion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pi t metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1984

[ ]

Jan 1, 1938

By J. Kostuik, M. J. de Bastiani

Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10° to 45° on the north limb and 10° to 20° on the south limb.

Jan 12, 1960

By John W. Tieman

Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased.

Jan 8, 1972

By O. B. Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos, (2) as to the principal sources of the raw material, and (3) as to the types and modes of the occurrence of asbestos.

Jan 1, 1915

By David Burgess, Hershiel H. Hayden

Experiments at the Somerset mine, Colo., under an agreement between US. Steel Corp. and the US. Bureau of Mines are described. A test was made of the tube bundle method of mine air sampling which was developed for European longwall mines; some 300,000 running feet of tubing provided continuous monitoring at 38 locations. Carbon monoxide concentrations were obtained with standard deviations of less than 1 ppm and oxygen concentrations with standard deviations of less than 0.2%. A base level of CO index (ppm CO evolved per percent 0, removed) was determined to be zero to 20 through most of the passageways of the mine. However, in one working section where the coal was initially hot (about 180°F within a pillar) the CO index was demonstrably higher, 120 trending upward to about 60 when smoke appeared and the section was sealed. The data are discussed in terms of laboratory experiments on CO evolution from coals.

Jan 1, 1977