Search Documents

By William Glenn

The Ritchie vein, of Ritchie county, W. Va.,* was a straight fissure, about 3600 feet in length, which cut vertically downward across the horizontal beds of shale and of sandstone to a depth not ascertained. It might be described as lying in a. Vertical plane, bearing 12 degrees north of west. The geological horizon is that of the " upper barren coal measures'" of the Appalachian coal-field, being a part of the strata lying above the Pittsburgh bed. The vein matter was declared by Prof.

Jan 1, 1896

By H. J. Booss

THERE is a considerable lack of data on thermody-namic properties of hard-metal alloys. Only two papers 1,2 give mean values of specific heat in an unknown temperature range; more recently the author3 gave more detailed information on the mean specific heat in the temperature range from 20" to -190° C.. EXPERIMENTAL 1) Method—Experimental procedure followed a method suggested by Oelsen and coworkers.4 It requires samples of some 100 g of weight. The time of measurement is prolonged (30 min) but one run allows the measurement of a lot of positions on the heat-content curve. Results4 were found to be in good agreement with "best values" given by kelley,5 Kubaschewsky and Evans,6 etal.

Jan 1, 1960

By Reuben B. Ellestad, Fremont F. Clarke

In the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2S04) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K,SO, is objectionable from cost considerations since purification of lithium carbonate re- quires the use of potassium carbonate, if the K2S04 is to be recovered and recycled. The lower solubility of K,SO, as compared with Na,SO, is also objectionable, since it limits the concentration of the Li,SO, solution to be precipitated by K,CO,. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging

Nov 1, 1955

By Rodolfo V. de la Cruz

The accurate assessment of the in situ deformability of rock masses is very important in the de and construction of underground openings for mining and geotechnical engineering applications. This paper presents a method and device for determining the in situ deformability of rock masses by relating the borehole jack load to the diametral displacements at a number of orientations around the borehole wall. The method called mu1tiple measurement method include the steps in which: a) diametral displacement sensors are installed at different orientations around the borehole to measure the changes in length of various diameters of the borehole; b) a uniaxial load is applied on two opposed octants of the borehole wall, and; c) using elastic theory and assuming a reasonable value for the Poisson's Ratio of the rock mass, the in situ deformability of the surrounding rock materials is determined from the measured diametral displacements and applied unidirectional load. The multiple measurement method has a significant advantage over existing methods since it provides several independent data in a single test from which to calculate the in situ deformability of the rock mass. The multiple data provide a check and counter check on the reliability and accuracy of the various measurements. The multiple data would also provide a means of quantifying the degree of fissuring on the borehole wall. Information on the degree of fissuring is very important in numerical modeling of rock masses.

Jan 1, 1984

By Roy Thomas

SOON after the Waelz plant for the fire concentration of low-grade zinc ores was put into operation in the early part of 1929 at Katowice, it was found that the conveyor equipment for transporting the hot residue from the furnace dust chambers was inadequate. Hand tram-ming with water cooling was used for a time, but that method was injurious to the workmen as well as costly. The problem was to find some practical mechanical means of conveying flue dust at temperatures of from 450° to 600° C. as it was drawn from the dust chambers. After considerable preliminary investigation it was decided to install pneu-matic equipment for conveying the hot materials to a central mixing plant, where it would be mixed with slime and from which it would be returned to the furnace feed hoppers. The first pneumatic equipment was installed in 1930, and has been in successful operation since that time. The pneumatic method of transportation has shown a considerable saving in operating costs over the former methods of dust handling and a decided improvement in working and hygienic conditions at the plant, through the elimination of the dust hazard. Additional pneumatic equipment was installed in 1933 for conveying the furnace fume from the baghouses to the roaster plant. At the same time pick-up lines were provided for collecting the cleanings from the vertical and horizontal cooling pipes that are between the furnace dust chambers and the baghouses. The latter installation has practically eliminated a dusty and costly hand-tramming operation.

Jan 1, 1939

By J. B. Rather

THE use of sulfuric acid in refining illuminating oils antedates the beginning of the petroleum industry in America by many years. It was used as early as 1792 by Tower in refining "coal oil" in the British Isles, and by 1860 there were 53 refineries in the United States manufacturing "coal oil," most of them using sulfuric acid as a refining agent. Following the completion of the Drake well in 1859, many of the "coal oil" refiners began to use petroleum for manufacturing illuminating oil, and their methods and equipment were adapted so far as possible to this new raw material. The value of sulfuric acid in refining "coal oil" having been established, this reagent was immediately tried and found to be satisfactory in refining petroleum. Notwithstanding the tremendous advances in petroleum technology since that time, sulfuric acid remains today the most valuable and most widely used means for refining petroleum products. EARLY METHODS OF DISPOSAL OF ACID SLUDGE With the almost immediate expansion of the petroleum industry came the problem of disposing of the acid sludge produced in the refining operations. While in 1859, the year of the discovery of the Drake well, a patent was granted for sludge separation and separated acid concentration, most of the earlier refiners, and many of their successors, felt that separation and recovery of spent acid was uneconomical. Accordingly, many of them disposed of the sludge in any way that seemed expedient at the time. It was buried in the refinery grounds, barged and dumped at sea, run into neighboring streams, or dumped into sewers. Some optimists carted it to open pits in the hope that it would either sink into the ground or evaporate. Not so many years ago, the superintendent of an eastern refinery, who was using the open-pit method of disposal, lost a sludge cart, with horse attached, in such a pit. The horse was recovered almost immediately, but its availability for further use was reduced to zero by the loss of its hair.

Jan 1, 1928

By F. L. Ransome

THAT geology and mining should stand in close and mutually helpful relationship was recognized in the United States at an early period, but it is not possible to set a precise date at which the study of ore deposits became a thoroughly reputable and important branch of geological science. As early as 1850, appeared the first ,part of Foster and Whitney's report1 on the Lake Superior region, devoted mainly to the copper-bearing areas, followed, in the succeeding year, by the second part,2 on the iron lands. This appears to have been the first comprehensive report on what might, at that time at least, be called "western" ore deposits to be prepared and published under the auspices of the Federal government. An outgrowth from this work was Whitney's Metallic Wealth of the United States,3 which appeared in 1854. It was the earliest general work on the ore deposits of the country, and remained a standard reference book for marly forty years. From 1853 on, various parties were sent out by the War Department to explore routes for proposed railways and wagon roads from the Mississippi Valley to the Pacific Coast. Geologists were attached to most of these parties, but their work was mainly of broad reconnaissance character, little attention being paid to ore deposits. Although the

Jan 1, 1933

By L. A. Weakly

The Viburnum ore trend is the largest, single known ore body of lead in the world. Four well-known mining companies operate in the trend, which is approximately 64 km (40 miles) long and up to 610 m (2,000 ft) wide, located some 121 km (75 miles) southwest of St. Louis, MO. Total production from the mines for 1979 was 33 kt/d (36,000 tons) of ore or 472 kt/a (520,350 tons) of lead and coproduct metal. The district is the number one producer of lead, providing 90% of the United States' output with its coproducts, zinc ranking second, and copper and silver both ranking sixth in total US output. Mining is done in a stratiform deposit approximately 305 m (1,000 ft) in depth with the host rock principally dolomite. Ore is mined in large open stopes by the method commonly referred to as room-and-pillar mining. Mining methods and equipment are fairly similar, with the mines classified as trackless, all mining equipment operates on rubber tires. This paper will present a description of the different methods and equipment used to move ore from the active heading underground to the ore shaft for hoisting to the surface. Basically, three methods are incorporated: front-end loader and truck haulage combination; front-end loader and truck, with main line track haulage combination; and front-end loader and truck, with conveyor haulage combination. The logistics of each system, such as method of use, equipment specifications, ore handling rate, and those cost figures that could be made public, will be included.

Jan 1, 1983

By Michael Tenenbaum

RECENT researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any sub-stantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed.

Jan 1, 1939

By Rudolf Bernhard

STATIC soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the appli-cation of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the practical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes.

Jan 1, 1938

By L. O. Bond, R. P. Alger, A. W. Schmidt

Well logging provides valuable information for planning coal mining operations. In addition to locating, defining, and evaluating coal beds, electrical logs indicate the relative competence of roof and floor formations. Electrical well logging is the .recording of various physical, chemical, or physicochemical properties of the strata penetrated by a drill hole. To perform logging operations, borehole measuring probes, or sondes, are lowered on a cable into the drill hole. Insulated conductors in the cable pass power to the sonde and transmit signals to the surface. As the sonde is pulled up the hole, the measurements are recorded as a well log. These measurements serve to define the formation lithology. Common rock minerals exhibit characteristic log values such that computer analysis of the log data defines the mineral content of the formations. Shales, carbonates and sandstones, and coal beds are readily distinguished. Furthermore, preliminary results in coal studies indicate the log data delineates variations in ash and moisture contents. Of major concern in planning mining operations is knowledge of roof and floor competence. Here again the logs provide valuable information. Measurements of formation density and acoustic wave velocity provide data for computation of a compressional modulus. This compressional modulus is an effective index of formation competence. Electrical logging thus efficiently provides information for economic planning of mining operations.

Jan 1, 1972

By M. C. Leverett

THE behavior of mixtures of immiscible liquids in porous solids is of rapidly increasing interest to those engaged in the production of petro-leum. The operation of artificial water-floods and the control of natural ones immediately raise questions concerning the fundamental nature of such processes. Moreover, it is now recognized that often water occurs dispersed throughout the rock from which the oil issues into the well,1 and thus tends to move toward the well simultaneously with the oil. The work reported here is a laboratory investigation of the simultaneous, steady-state flow of oil and water through the same column of uncon-solidated sand. It is thus directly related to the situation in which water occurs in oil-producing sands; it may have less direct implications for the displacement of oil from sands by water. However, it is to be clearly understood that the experiments to be described were performed pri-marily to obtain information of a more or less fundamental nature, and are not an attempt to reproduce, on laboratory scale, any part of an oil field. The dynamic behavior of a system in which oil and water are flowing simultaneously through sand is best described in terms of its "effective permeability" to either phase. For incompressible fluids flowing through a system of uniform cross section, the effective permeabilities to the two phases, in darcys, may be defined by the equations:

Jan 1, 1938

By David White

THE environmental conditions under which coals are deposited are revealed by the stratigraphy of the coal basins and coal beds and by the details of the structure and the physical constitution of the coals themselves. THE LAND SURFACE Generally Low Relief or Base Level In the Paleozoic coal fields, which have longest been worked, are most important, and are best known, we find relations, in general, as follows A post-Mississippian uplift with, in most cases, very moderate deformation, followed by erosion by which the uplifted regions, especially the bolder of the new topography, were largely worn down, while the older and less deformed regions were more or less extensively base leveled. Base leveling of most of the region continued as the deposition of coal measures proceeded. Consequently, in most coal fields the Pennsylvanian, or upper Carboniferous, lies unconformably on the Mississippian or on older formations. There are but few regions in which sedimentation is seen to have been apparently continuous from the Mississippian into the Pennsylvanian ("Coal Measures").

Jan 1, 1925

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918

By E. J. Roberts, E. B. Fitch

THE mechanism of classification by settling pools is most simply shown in the case of batch sedimentation such as was analyzed by Oden.1 The batch model will be considered, therefore, and it will be shown that the same mechanism applies to continuous operation. Classification in Batch Settling Pools: Consider a beaker or tank of slurry containing particles so dispersed that they can settle independently of one another under the influence of gravity. Originally all particle sizes are uniformly distributed throughout the suspension. All particles start immediately to settle towards the bottom at rates determined by their size, shape, and density—among other factors. Particles reaching the bottom settle out of suspension. After some given time the slurry above the deposited solids is siphoned off or otherwise removed, leaving the deposited solids behind. The deposited solids, together with entrained and any unremoved supernatant slurry, represent the underflow of a classifier. The slurry removed represents the overflow. There is a certain separation, size of particle which during the sedimentation has just time to settle from the top surface of the slurry to the level at which underflow and overflow are parted. All particles with a faster settling rate will have dropped to below this level, no matter where in the beaker they started from originally, and therefore will be absent from the overflow. Particles with a slower settling rate will not reach this level if they started from the top of the slurry, but a portion of them,

Jan 1, 1957

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,' from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

By C. W. Tomlinson

The analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates1 of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineral-ogical constitution of aggregates upon the properties of the concrete and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting is of course dependent upon the experience and carefulness of the analyst. After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed from 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reasonable limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hun- dredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 1, 1916

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 10 to Feb. 10, 1915: Members AGASSIZ, RUDOLPH Louis, Vice-Pres.,Calumet & Hecla Mining Co., Boston, Mass. AMIDON, RICHARD G., Min. Engr 3659 Girard Ave. N., Minneapolis, Minn. ANDERSON, HECTOR G. S., Min. Engr 323 N. 13th St., Muskogee, Okla. ANDERSON, JOHN CARTER, Petroleum Engr 2307 S. 33d St., Omaha, Neb. CLARKE, ALEXANDER FIELDER, Works Mgr., Firth-Sterling Steel Co., McKeesport, Pa. CROSS, CARLOS GARCIA, Min. Engr Calle Valparaiso 194, Vina del Mar, Chile. DAWSON, THOMAS WILLIAM, Min. Engr., Asst. Chief Engr., H. C. Frick Coke Co., Scottdale, Pa.

Jan 3, 1915

By Lawrence W. Teufel

A method to determine in situ stress directions and magnitudes from anelastic strain recovery measurements of oriented core has been used to determine the principal horizontal in situ stresses in the Rollins Sandstone in a deep well near Rifle, Colorado. The principal horizontal stress directions were determined directly from the principal horizontal strain recovery directions. The principal horizontal stress magnitudes were calculated from the principal strain recovery magnitudes, overburden stress, and Poison's ratio of the rock using a viscoelastic model. The accuracy of the in situ stress directions and magnitudes determined from anelastic strain recovery measurements was substantiated by a direct comparison with open-hole hydraulic fracture stress measurements. The anelastic strain recovery method predicted the magnitudes of the maximum and minimum horizontal principal stresses to be 54.5 MPa and 51.9 MPa, respectively; with an azimuth of N63ºW ± 8º for the maximum horizontal stress. The hydraulic fracture stress measurements yielded maximum and minimum horizontal principal stress magnitudes of 49.6 MPa and 46.8 MPa, respectively. The azimuth of the maximum horizontal stress ranged from N50ºW to N70°W.

Jan 1, 1984