Search Documents

By H. F. Silver

Although the literature indicated that a hydrogen-ated coal bitumen might be used as a substitute for petroleum asphalt and road tar, no work could be found in which the material was actually used or evaluated as a road binder.' Therefore, a study was initiated to investigate the production and properties of a road binder made by hydrogenating coal in the presence of a solvent at elevated temperatures and pressures. HYDROGENATlON PROCEDURE Four different samples of sub-bituminous Wyoming coals and three samples of coals from other states, ranking from lignite to a low-volatile bituminous coal,

Jan 1, 1969

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one service hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown.

Jan 3, 1953

By Peter M. Grant

The paper describes in broad outline the design of circular shaft linings with particular reference to the practical aspects. In the main it refers to recent British and German practice but has general application for any shaft lining design.

Jan 1, 1983

By B. B. Sandiford

It has been known for many years that the efficiency of a water flood can be improved by lowering the water-oil mobility ratio in the system. Such a change leads to better sweep efficiency and also to more efficient oil displacement in the swept zone. Data from our laboratory water-flood tests of both small cores and long sand packs are presented which show that water mobility can be reduced and oil recovery increased by the addition of certain polymer solutions to flood water. The reduction in mobility, in many cases, is greater than would be expected from conventional viscosity measurements. These solutions, however, do not cause significant reductions in oil mobility. The over-all effect of these mobility changes is increased waterflood oil recovery. Encouraged by results of our laboratory work, we expanded our study to include pilot field tests of floods with such solutions. One such test, made in the West Cat Canyon field, Santa Barbara County, Calif., is described in detail in this paper. Three other field tests are also discussed. INTRODUCTION Oil production from most reservoirs following primary depletion and/or water flooding is often less than 50 per cent of the original oil in place. Heavy oil reservoirs seldom yield over 15 per cent of their original oil. With new reservoirs becoming harder to find, the improvement of oil recovery efficiency is one of our very important problems. We describe here some of our attempts to increase the efficiency of oil displacement by adding a water-soluble polymer, partially hydrolyzed polyacrylamide, to flood water. This technique will be termed "polymer solution flooding". The concept of using high-viscosity water to increase the efficiency of water flooding is not new. In 1944 Detling (Shell Development Co.) obtained a patent covering the use of several additives for viscous water flooding.' His objective was to improve water-oil mobility ratios by increasing the viscosity of the flood water. Other patents2-27 have been granted covering specific water-SO~LIble polymers or specific conditions of viscous water flooding. Barnes'" described his laboratory model study of the injection of a viscous water slug into a reservoir which had been partially invaded by bottom water. He concluded that, for this type of reservoir, "the cost of viscous water should not exceed a few cents per barrel for viscous water slug injection to be economically feasible" Our studies have led us to a somewhat different conclusion in a number of cases where hydrolyzed polyacrylamide solutions have been injected into reservoir models or actual reservoirs. Possible reasons for this difference are discussed in this paper. Our studies have shown that polymer solutions may lead to an increase in oil recovery over that from an ordinary water flood by (1) improving sweep efficiency, (2) improving microscopic displacement efficiency, or (3) a combination of these mechanisms. In the work of Barnes, only the benefit of improved sweep efficiency was considered. Also, our work has shown that there are marked differences in the effectiveness of different water-soluble polymers as flood water additives. Partially hydrolyzed polyacrylamide is better than many other water-soluble polymers we have tested because, even in very low concentrations, it can lead to increased oil recovery. This is an important advantage when either a dilute polymer solution is injected continuously or a relatively concentrated slug is injected followed by water. In the latter case! portions of the slug become diluted and function in the formation as very dilute solutions. As dilution takes place the effective slug size will increase which, in turn, will reduce the cost per barrel of the effective flooding medium. The reason that partially hydrolyzed polyacrylamide solutions are more efficient at low concentrations than certain other polymer solutions of equivalent viscosity (when measured in conventional viscometers) is not fully understood. We do know that the shapes and sizes of macro-molecules dissolved or suspended in liquids influence the flow properties of their solutions or suspensions. Solutions of partially hydrolyzed polyacrylamide cause greater reductions in water mobility than would be expected from conventional viscosity measurements. LABORATORY STUDIES Laboratory water floods were run in linear and radial systems with different water-soluble polymers and under varying conditions of flow. including reservoir conditions of temperature, pressure and fluid composition. Some of these runs are considered in this section. OIL DISPLACEMENT IN LINEAR MODELS In this group of runs the sweep efficiency approached 100 per cent because the linear sand packs used were as nearly uniform as possible. Results reflect primarily the micro-scopic displacement efficiencies. The laboratory models were unconsolidat-ed sand packs the lengths of which varied from about 4 in, to 40 ft. Further information on the flow models used is listed in Table 1. Using conventional procedures, water floods were run on sand packs containing either refined or crude oil at restored state. Frequently, a repeat run, similar to the first, was made as a check. Then a third run was made on the restored-state model using either polymer solution or a combination of polymer solution (slug) and water. Details of these runs are also reported in Table 1. In Figs. 1 and 2 results of two different groups of runs are shown in which the oil used was a 62-cp refined oil and the flooding medium

Jan 1, 1965

By J. C. Norman

Jan 1, 1985

By Ronald J. Roman, Craig Olsen

Alterations were performed on a previously developed heap leaching model representing sulfuric acid solution leaching of a malachite sandstone ore. The alterations were made in order to approach a more realistic solution to the leaching equations used in the model and to provide a means of obtaining a constant acid con- centration in the model' s simulated heap effluent solutions. This constant acid concentration is desired if the effluent solutions are to be treated in a solvent extraction-electrowinning plant. An economic study was made showing a use of the leaching model for an imaginary heap leach operation. The example illustrates a method of selecting heap leaching parameters if data are available on mining costs, dump costs, capital cost, etc. This was achieved using an incremental investment technique.

Jan 1, 1974

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 5, 1950

By Forbes Wilson

IN February 1952 Freeport Sulphur Company started exploration work on a group of lateritic deposits at Moa Bay, Cuba. As a result of successful exploration work and a vast amount of metallurgical research over the past five years, these deposits will soon become a new Free World source of nickel and cobalt. Moa Bay lies on the north coast of Oriente Province, the easternmost part of the island, about 600 miles east of Havana and about 40 miles east of the U. S. Government nickel plant at Nicaro.

Jan 5, 1958

By S. G. Malghan

Steel consumption forms a significant part of the operating cost of a minerals processing plant. An estimated 250 kt (276, 000 tons) of steel in the US and over 500 kt (551, 000 tons) worldwide are consumed each year in wet grinding alone. The depletion of ore grades and the need for finer grinding of abrasive ores are expected to increase steel consumption even more. Through continued research and development by the mining industry and the suppliers of steel products, several methods to reduce steel consumption have evolved. This paper critically reviews the mechanisms involved in steel wear and the currently available methods, materials. and operating conditions for reducing steel consumption. Particular attention is given to liner design modifications and substitution of rubber liners for steel liners.

Jan 1, 1983

By R. C. Wilmoth, R. D. Hill, R. B. Scott

A cost breakdown is given for reclamation and mine drainage abatement conducted by the Federal Water Quality Administration's demonstration project near Elkins, W. Va. Costs for construction of control measures have been developed and include backfilling strip mines, sealing subsidence areas, reconstructing stream channels, and installing mine seals to prevent the entrance of water and air.

Jan 1, 1973

By George Kenzy, Charles B. Manula

This paper introduces a philosophy of dynamic modeling. Here, the development of a simulation model of a coal mining system is described for the purposes of: (a) system design and selection of equipment for a new operation; (b) analysis of existing operation' for possible alterations, additions, or general improvements.

Jan 1, 1976

By F. R. S., B. Hopkinson, R. Hadfield

A short time ago Professor Stoughton askes the writer if he would present a paper for the Feburary meeting of our Institute.

Jan 1, 1915

By Paul A. Beck, A. H. Lutts

IN a previous paper' isothermal softening and X-ray line sharpening data were reported for the annealing at 350°C of single crystals of pure aluminum rolled on the (110) plane in the [112] direction. It was shown that, after rolling to 80 pct reduction in area and careful etching in such a manner as to eliminate extraneous orientations by removing surface material and disturbed areas adjacent to saw cuts, the specimens may be extensively annealed at 350°C without any observable recrys-tallization. At the same temperature, the line broadening caused by cold rolling was found to disappear practically completely after less than 200 sec of annealing. The present work was undertaken in order to study the temperature dependence of line sharpening and of the initial softening with high purity

Jan 1, 1957

By Alan E. Gallie

SHERRITT Gordon Co. was formed in 1927 to exploit a copper zinc orebody located in the bush 90 miles north of The Pas, Manitoba. The mine went into production in 1931, operated for a year and a half, and closed because of the low price of copper. Reopened in 1937, it operated continuously until mined out in 1951, producing 8.5 million tons of ore. From 1937 on Sherritt Gordon conducted an energetic prospecting program throughout northern Manitoba, giving particular attention to the belt of favorable greenstone rocks north of the Churchill River. From 1937 to 1941 a number of gold showings were located but nothing of economic value was found.

Jan 3, 1957

By Leo Dana

INTRODUCTION THE object of this paper is to discuss the factors and conditions that affect the observed values of the melting points of refractory materials and to describe practical methods for the determination of these points. While it appeared to be necessary to discuss some of the general properties of silicates and refractories, these subjects have been entered into only in so far as they relate to the melting point and its determination. Refractory materials such as fireclays, firebricks, and minerals generally, may be considered to be composed of compounds of metallic oxides, solid solutions of the oxides, the pure oxides, or mixtures of the three classes together with small amounts of a variety of chemical compounds. The oxides of silica and alumina occur most commonly in refractory materials; in combination with. these, oxides of the alkali earth, the alkali, the iron group, and the rare earth metals are frequently found.

Jan 9, 1919

By H. J. Ward

RUM Jungle uranium field lies in the subtropical portion of the Northern Territory on the Finniss River, East Branch. It takes its name from a railway siding about 2 ½ miles to the southwest and 52 miles from Darwin. The field can be reached from Darwin by a bituminized road. Monsoonal rains of the wet season, October to April, provide an annual rainfall of about 60 in. Vegetation is of the open forest type with denser tree growth along the watercourses and scattered throughout the area are isolated dense patches of jungle growth which are always found on ironstone cappings overlying limestones. The name, Rum Jungle, is thought to have been derived from this unusual occurrence of jungle growth. The wet season prevents the movement of motor vehicles and personnel. It is not until March, when the grass which ranges up to 15 ft in height is burned and the alluvial flats dry out, that field work can be undertaken.

Jan 12, 1954

By Dave H. Barnett, Brij M. Moudgil

The flotation technique as employed by Florida phosphate producing companies for the beneficiation of fine phosphate particles has been standardized over the years. Lower recoveries of coarse Phosphate rock by froth flotation technique, however, led to the development of new methods based on skin flotation of phosphate agglomerates. Recent developments of floating coarse rock in large flotation machines have not yet convinced the rock Producers of their higher separation efficiency. It is interesting to note that the selection of a particular machine is still bared on equipment preference by an individual company as well as proven performance of a particular machine for upgrading a specific material. Various techniques which have been developed to beneficiate the coarse phosphate rock have been discussed. Performance of the individual techniques is presented.

Jan 3, 1979

Scientific elite of the Minerals Beneficiation Div. assembled in Denver, Colo., September 17 to 20 to commemorate the 50th Anniversary of Froth Flotation in the United States of America. In his warm address of welcome at the opening luncheon, John W. Vanderwilt, President, Colorado School of Mines, recalled his experience in Bonanza which coincided with the early days of flotation. In those years the scientific and engineering aspects of the process which we know today were little understood and operating the flotation circuit was considered an "art." Luncheon Chairman H. L. McNeill caught the flavor of the old days in an anecdote which recalled the mill nightmares to many present with the agonized words, "Oh God, what's happened to the concentrate now!" It was an appropriate gesture when he called the names of some of the flotation greats for presentation to the assembly; and many an "artist" there was among them!

Jan 10, 1961

Conquista, the uranium mining and milling complex owned jointly by Continental Oil Co. and Pioneer Nuclear, Inc., has begun operations in Falls City, Texas. The mill has been designed to produce 1.5 million lb of U3O, from 600,000 tpy of ore mined. Currently, the plant processes a maximum 2000 tpd of ore. Mine Planning Texas ore deposits are small and scattered in comparison to other uranium mining districts. Those to be mined at Conquista range from a few acres to more than 100 acres in size. Ore thickness ranges from a few inches to over 15 ft, and depth from less than 20 ft to more than 170 ft below ground surface. Distance from the mill ranges up to 35 mi.

Jan 8, 1972

By A. F. Peterson, A. R. Eshbach

Much has been written to explain decreasing profits in American industry. Foreign competition, the attitude of government, rising tax burdens and increased labor costs have been blamed in turn. Whatever the cause, management in the mining industry, as elsewhere, is increasingly aware of diminishing profit margins. A mine operator is usually unable to do much about the causes of decreased profits, even if he knows what they are, but he can check the trend in part by cutting the cost of operation. To do this, he must know what his costs are, which of them are most significant and then go about reducing them in a systematic and logical manner.

Jan 10, 1962