Search Documents

By George I. Smith

Jan 1, 1985

By N. Mungan, J. L. Thompson

Laboratory displacement tests were performed to study oil recovery elficiency by gravity drainage in fractured systems under miscible conditions. The porous media used were cylindrical Berea and Blue Jacket sandstone cores containing a number of well-defined, artificially formed, vertical and subvertical fractures. Butane and Soltrol 130 were the two miscible fluids used. The purpose of the study was to examine the influences of the displacement rate, fracture density, fracture orientation, fracture permeability, matrix permeability, crossflow, core length and connate water on the oil recovery. It was found that displacement rate, matrix permeability and the subvertical fractures affected oil recovery most. The critical flow rate, based on the matrix permeability, was found to be a significant factor in the process. For displacement rates below the critical flow rate, the oil recovery efficiency appeared to be unaffected by the density of the subvertical fractures. At the high displacement rates, the fracture density becomes important, with the recovery being the most efficient in the core having the greatest number of the subvertical fractures. The magnitude of the fracture permeability, the fracture orientation, the core length and the connate water have little effect on the oil recovery efficiency. INTRODUCTION Gravity drainage under miscible conditions from relatively thick reservoirs can be a very efficient recovery process, especially at low flow rates where the gravity forces are dominant and, consequently, the adverse viscous fingers associated with the unfavorable viscosity ratio are minimized or eliminated. Such a process might involve injection of an LPG or some solvent bank at the crest and then driving the bank with dry gas. For some favorable combination of reservoir temperature, pressure and oil composition, there may be no need to inject any solvent bank, since enrichment of the dry gas by the light ends of the crude creates an in-situ solvent bank. Slobod and Howlett2 have studied the effects of gravity segregation in vertical unconsolidated porous media under miscible conditions in the laboratory. The main variables in their study were the viscosity ratio, the density differences and the rate of flow. In this study, the objective was to find the influence of fractures on gravity drainage under miscible conditions. A greater number of related variables were also studied. LABORATORY STUDY CORE DESCRIPTION Displacement tests were performed mostly in cylindrical Berea sandstone cores. In a few cases in which a much lower matrix permeability was desired, Blue Jacket sandstone cores were used. The vertical fractures were formed by cutting the cores with a thin circular blade or by parting them along a bedding plane. The vertical fracture plane always contained the axis of the cylindrical core. The subvertical fractures, cut with a saw, were inclined 45' from the horizontal. The line of intersection between the planes of the vertical and subvertical fractures was parallel to the circular faces of the cores in all cases except one, as depicted by VF3HF-2 in Fig. 1. Fracture geometry of the other cores is also given in Fig. 1. Tables 1 and 2 give the physical properties of the solid and fractured cores, respectively. The suffixes and prefixes shown for each core have been used throughout the paper so that the reader may discern the fracture geometry from the core numbers.

Jan 1, 1970

By R. J. Lutton

Empirical data from 91 rock excavations have been used to construct a family of slope curves on a chart relating excavation height and inclination. The highest and steepest slopes from each excavation are plotted and connected by a line. The 31 1ines appear to establish one or two geometrical slope fields through which the curves are projected. The curves apparently represent a lumped eflect of many factors too complex to be considered individually. Important factors such as geological structure or ground-water conditions can dominate the picture, but where these factors do not overshadow others, the slope chart should be useful for estimating or checking optimum inclination. The U.S. Army Corps of Engineers (USAE) has been engaged since 1962 with the U.S. Atomic Energy Commission in a joint research program to develop nuclear excavation technology. The Corps is responsible for collecting the requisite data on engineering and construction problems associated with nuclear excavation. The ultimate objective is to develop a capability to use nuclear explosives as a construction tool on public works projects such as harbors and canals. The present study on empirical inclination-height curves for conventionally excavated slopes is an outgrowth of an investigation' sponsored by the USAE Nuclear Cratering Group on applicability of data from existing excavations in establishing guides for engineering judgment in crater excavation. Data were generously contributed by over 50 mining companies among other organizations. Inasmuch as several companies preferred that their contribution be anonymous, all data are treated so here. Some Factors Affecting Stability Many factors affect or are suspected of affecting the stability of excavated slopes, e.g., adverse structural orientation, degree of structural ordering, ground water, climatic conditions, mechanics of excavation, and plan-profile configuration. Such factors are lumped together in developing a slope chart. Obviously geological structure and ground water can overshadow all other factors. Where such is the case, the simplification of slope charts may give an erroneous picture (not conservative enough). A further complication results from the fact that the concept of stability may vary according to the use of the excavations. For example, slope adjustments that would be regarded as failure in a powerhouse excavation, might be tolerable in a mining operation. Mine slopes are continually being modified by further excavation, and instability that would develop in a similar permanent excavation slope over a period of years might not have time to develop in a mine. Inclination vs. Height Charts Charts of inclination vs. height for particular formations or conditions have been used in the past as an aid for designing excavation slopes. Some of these have been based upon empirical analyses of collections of data and experience. MacDonald" and Lane have presented slope tables and charts for excavated and natural slopes in relatively weak sandstone and shale. Coates' has shown an inclination-height chart for slopes in incompetent rock. Most organizations have developed slope design criteria which relate bench widths, heights, and inclinations to use in various rocks. Slope data collected in present studies can be similarly used to develop inclination-height charts; however, a plot of all slopes on such a chart shows very little because of the wide spread of the data. Reasons for the dispersion of points are: (1) many slopes are not carried at optimum inclination, particularly in mines where maintaining roadways and following irregularities of ore bodies are more important than achieving steep inclinations; (2) many engineers and geologists with varied backgrounds and viewpoints have been involved in designing these slopes; and (3) each slope is characterized by a unique combination of factors affecting stability and in turn optimum inclination. Significant curves can sometimes be constructed where the points can be grouped into related clusters from the same excavation. The essence of this approach appears when only two slopes from each excavation are considered—the highest slope and the steepest slope, connected by a line segment (Fig. 1). This reduces considerably the usable data because in many cases only one of these two slopes is available. Nevertheless, the concession seems justified. Construction of Slope Curves Ninety-one pairs of points and connecting line segments were assembled in this study. The line segments were assumed to approximate a geometrical slope field (Fig. 2), and a family of curves has been visually projected through to represent the slope field. It should be

Jan 1, 1971

By N. A. D. Parlee, E. M. Sacris

OXYGEN solubility in liquid silver has been well studied.1-6 It has been established that the solubility follows Sieverts' law reasonably well5'6 up to po2

Jan 1, 1968

By C. C. Miller, C. A. Hutchinson, A. B. Dyes

This paper presents a simple and practical method for the estimation of effective permeability and reservoir pressures from the rise in bottom hole pressure when a well is shut in. The equations on which the method is based consider a stabilized well producing from a uniform formation when flow is shut off at the sand face followed by the unsteady state flow of a compressible liquid from regions far from a well to points closer in during the build-up period. An approximation for extending the method for two-phase flow in the reservoir is also presented. In order to compare the effects of extremes in the conditions existing at the external boundary of the reservoir, two general equations defining the build-up characteristics of the reservoir are shown: first, for a reservoir with constant pressure maintained at the radius of drainage, and second, for a reservoir with no influx over the radius of drainage. These equations define the build-up characteristics for the shut-in well as functions of time, the permeability and porosity of the drainage area, the viscosity and compressibility of the fluid flowing, the production rate prior to shut-in, and the radius of drainage of the well. When a well is shut in at the surface, rather than at the sand face, flow will continue into the well bore after shut-in due to the compressibility of the fluids in the bore. The effect upon the build-up characteristics of this flow into the well after shut-in has been studied by means of the electrical analyzer. From the basic relationships and consideration of the limitations due to continued flow after shut-in, methods have been developed for the estimation of the effective permeability of an area from the plot of the build-up characteristics of the well producing that area. Likewise, equations are presented for the estimation of the reservoir pressure from an early portion of the build-up curve. By means of the electrical analyzer, studies have been made concerning the variations in the build-up characteristics resulting from damaged or improved permeability in the immediate vicinity of the well bore. These studies show that the permeability estimated from the build-up curves represents the average effective permeability of the majority of the drainage area and that the permeability in the immediate vicinity of the well does not affect this estimate. Since the major portion of the drawdown is in the immediate vicinity of the well, variations in the permeability of this area greatly affect the productivity of the well as expressed by the productivity index. From pressure build-up and productivity index tests the ratio of the permeability of some arbitrarily specified area immediately surrounding the well and the effective permeability in the majority of the drainage area can be computed. This ratio is a measure of any damage to the well incurred in drilling or reworking and likewise any benefits as a result of remedial measures. In build-up tests and many other tests that are made on a producing well it is at least desirable, if not absolutely necessary, that the well be stabilized prior to testing. A method is presented here for relating the time required to stabilize a well and the reservoir and fluid properties. An equation is also presented for approximation of the length of shut-in time required to obtain sufficient build-up data for the estimation of permeability and reservoir pressure.

Jan 1, 1950

By H. D. Hoskold

This paper is presented in fulfillment of the promise made in my paper, " Remarks upon Surveying-Instruments,"" etc., and much of the material which would constitute an appropriate introductioil here is omitted, because it has been already published by the Institute, in connection with my own contributions- or those of Mr. Scott and others, in vols. xxviii. to xxxi. of the Transactions, and in the special Institute volume on Mine-Surveying Instruments. In these preceding publications will be found, for instance, descriptions of the writer's " miner's transit-theodolite" of 1863,† and his later " angleometer,"‡ both of which were steps of the progress in engineering instruments and methods which originated in the work of Bourns, before 1842, on the " BoxTunnel " of the Great Western railway in England, in which he had to make connections by direct telescopic sights down the shafts. About 1870 the writer devised a practical and much superior plan, and made detailed drawings for an instrument to meet all the conditions he had proposed prior to that year. The detailed plans were communicated to a celebrated optical firm in London; but, owing to their loss (in Paris or Germany, it is believed) and to other reasons, the matter was, for the time, allowed to lapse. Following upon Bourns's idea, my friend, the late Mr. Beansland, introduced, in 1856, a new system and a portable astronomical instrument.§ Such instruments, however, were neither common nor convenient, and did not come into general use among engineers.

Jan 1, 1902

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent papers on interface energies in metals¹,² the concept of an equilibrium of forces has been used in the measurement of interfacial tensions. Mathematically the equilibrium of three forces is given by the relations: where the 2's are the interfacial tensions (interface energies per unit area of interface) of three phases or grains meeting at angles 21 22 and 23 (212 relates to the 1-2 boundary formed by grains 1 and 2;223 to the 2-3 boundary, etc.). If these relationships are valid, one can calculate relative values of the interface energies from measured boundary angles on specimens which have been brought to equilibrium. Since Eq 1 may be derived through a mathematical process of minimizing the grain boundary energy under the restriction that the ?'s be independent of boundary orientation: the concepts of surface tensions and equilibrium of forces are not particularly essential. To deal with the general case involving dependence of boundary energy on boundary orientation, it becomes desirable to drop certain concepts formerly held (namely that energy per unit area is identical with force per unit length or surface tension) and to use the energy concept alone. It is appropriate, therefore, to use E in place of ? in deriving and using the more general equations that express the anisotropic nature of the grain boundary energy. Herring3# ' recently has derived the required general equations using the principle of minimization of energy. Specifying the boundary orientations in terms of angles (4) measured with reference to crystal axes within the grains, Herring's equations take the form E23 + E21 cos?8 + E12 cos?2 — sin ?12 + sin?2-?E12/?12 =O [2] where the partial derivatives are measured in the direction of counterclockwise rotation of the boundaries. Eq 2 implies that an infinitesimal displacement of the triple point along the 2-3 boundary produces no change in the boundary energy. Similar equations apply for infinitesimal displacements along each of the other two boundaries. From such equations Herring obtains the following general relationship (1 + E1 E2) sin?8 + (E2 — E1) cos?3 ________ E38______________ = (1+ E2 E8) sin ?1+ (E3— E2) cos ?1 __________^5____________[3] (1 + E sin ?2, + (E1 — E8,) COS ?2 1 E28 where E1 = 1/E23- E25 and PC and c8 have similar expressions. It is apparent that Eq 3 reduces to Eq 1 when the c's vanish. Eq 3 also reduces to Eq 1 when the E'S are all equal. Shockley and Read' have pointed out one limitation to these equations. When E plotted versus 4 appears as an energy cusp, as their theory requires, for example, for the energy near a twin boundary position, then Eq 3 (and therefore Eq 1 also) no longer applies if one boundary is in the minimum energy position. One of the equations of form Eq 2, however, applies if the infinitesimal displacement is along the boundary associated with the energy cusp. From the foregoing treatment it will be apparent that equilibrium angles alone are not sufficient in general for calculating relative interface energies.

Jan 1, 1951

By Robert E. Campbell

Mining geophysics in 1969 marked a year of growth and consolidation in the application of ground and airborne geophysical methods and techniques with a 20% rise in expenditures for world-wide exploration. Growth was determined by questionnaire survey of industry, geophysical contractors, universities and government agencies conducted by the Society of Exploration Geophysicists. Relative position of metlhods is shown in the accompanying table on page 87. Methods and Techniques Electromagnetic airborne and ground methods showed the largest gains in the utilization of VLF-EM instrumentation. The VLF-EM instrument is a directional radio receiver which is tuned to distant radio transmitters in the 15 to 25 kilohertz band range. It measures vertical real and imaginary components of the magnetic field vector, and is used in geological mapping and surveying for various types of conductors in the ground. Ground VLF-EM instruments, Ronka EM-16 and Radem, are manufactured by Geonics, Ltd., Toronto, Ont., and Crone Geophysics. Ltd., Port Credit. Ont.

Jan 1, 1970

By Nicholas J. Grant, Gordon D. Gemmell

CREEP rupture characteristics of high purity Al-Mg solid solution alloys were studied by Mul-lendore and Grant' to investigate solid solution strengthening of pure aluminum and the accompany- ing effects on deformation and fracture characteristics. This paper presents the results of an extension of that work to A1-Cu and Al-Zn alloys to permit a comparison of the relative effects of the three solute elements on the high temperature strength and on the deformation and fracture characteristics. Experimental Procedure A total of nine alloys was studied. They were all made of ultra high purity aluminum alloyed with high purity copper, zinc and magnesium. The corn-

Jan 1, 1958

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,' Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.' Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev's methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen' presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970

NEW MEMBERS The following list comprises the names of those persons who because members during the period Jan. 10, 1916 to Feb. 10, 1916. ATWATER, MAXWELL WANTON, Min. Engr Box 156, Basin, Mont. BARKDOLL, IVAN HARRY, Supt. of Mines, Old Dominion Copper Mill. & Smelt. Co., Globe, Ariz. BEAUDRY, WILLIAM A., Managing Director ....Stewart Mining Co., Kellogg, Ida. BRIGGS, CHARLES H Mill Supt., Admiralty Zinc Co., Miami, Ariz. CHURCH, L. C., Min. Engr Joplin, Mo. DAVIS, LLOYD J., Sales Engr; Ingersoll-Rand Drill Co., Joplin, Mo. DAVIS, SIDNEY H., Mgr Century Zinc Co., Joplin, Mo. DUGAN, J. H., Engr. and Contractor 65 N. Vine St., Hazleton, Pa. ELLIS, HUBERT INGERSOLL, Min. Engr., Bunker Hill & Sullivan MILL & Cons. Co., Kellogg, id..

Jan 3, 1916

By F. H. Parsons

At the time that converting or bessemerizing of copper matte first began to be practiced by the smelters in the copper industry, converters were lined by tamping the flux, usually siliceous ore, into the steel shell. About 1910, practice in several plants had demonstrated the superiority of a basic lining of nonfluxing material and the addition of flux through the mouth of the converter. Adoption of the new method by nearly the entire industry followed. Basic linings are made of refractory "magnesite" brick manufactured, usually, from imported dead-burned magnesite. Either the linings are laid up in the shell dry or the bricks arc bonded with some mortar dictated by the preference of the user. Foreign, usually Austrian, magnesite was the main source of supply for these bricks, although there were domestic sources, but it was not until costs began to rise a few years after the first use of basic linings that these domestic sources were investigated to any great extent. Exigencies created by the World War necessitated the use of the domestic magnesite during this period, but the brick manufacturers reverted to the use of the foreign product after the war, because the impurities therein made a brick with a better fire bond than the purer domestic magnesite. Therefore the domestic product became available at a favorable price for any metallurgical process that permitted its use. The United Verde converting practice using magnesite linings has resulted in a high consumption of magnesite because of the zinc content of the low-grade matte. It was realized that the cost of these linings represented a large portion of the cost of converting, and an investigation was started to find means by which these costs might be lowered. In the neighboring state of California rather pure magnesite was being mined and treated for the market. The product, however, was purposely made to simulate the dead-burned grain magnesite product from foreign sources by the addition of fluxing impurities before burning. It was learned that this dead-burned California grain magnesite could be laid down in Arizona at a price one-third that of the same tonnage of "magnesite" brick manufactured from foreign magnesite. It was also learned that at least one California producer was ready to supply the market with periclase, which was a grain magnesia produced by burning the

Jan 1, 1934

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By Carl Henrich

Jan 1, 1890

Executive A. R. LEDOUX, Chairman GEORGE D. BARRON SIDNEY J. JENNINGS J. V. N. DORR J. E. JOHNSON, JR.¬ Membership J. E. JOHNSON, JR., Chairman KARL EILERS F. F. SHARPLESS R. M. RAYMOND LEWIS W. FRANCIS Finance J. V. N. DORR, Chairman CHARLES F. RAND J. V. W. REYNDERS Library E. GYBBON SPILSBURY,' Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE' JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By E. Martinez

Samples of chrysocolla, a hydrated copper silicate, from several sources were submitted to differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). Pure samples of chrysocolla are difficult to obtain, but comparison of the thermograms revealed that certain reactions occurred in all the samples and it is believed that these are due to chrysocolla. Endothermic reactions occurred at 50' to 175°C, 350° to 650°C, and 980° to 1100°C each of which caused a weight loss. The first was due to loss of absorbed water, the second to a dehydroxyla-tion, and the last to conversion of cupric oxide to cuprous oxide. In addition, two exotherms were detected at 685° to 695°C and 935° to 950°C. Infrared spectra of heated samples indicated the exotherms were due to changes in the Si-O bonds leading to the formation of cristobalite. The results suggest that thermoanalysis may be a more sensitive and reliable method for detection and identification of chrysocolla than X-ray diffraction, infrared spectroscopy, or optical techniques. The recovery of copper from oxide ores has been the subject of much research in recent years. One of the principal oxide copper minerals is chrysocolla, a hydrated copper silicate. The information available indicates that it has widely varying properties depending on the origin of the sample. Chrysocolla usually is found associated with cuprite, malachite, azurite, and native copper. Most of these other minerals are recoverable by present day flotation practice, but chrysocolla is lost in the tailings.1,2 Reagent combinations that are successful in laboratory chrysocolla flotation with ore from one source have been found to be ineffective with another. 3 The copper segregation process offers an altemative to beneficiation of oxide copper ores.4'5 The process is of particular interest in processing ores that cannot be treated by conventional hydrometal-lurgical methods because of high acid consumption.6 Fuller understanding of the properties of chryso- colla may prove of value in the search for improvements in both the flotation and segregation processes. Chrysocolla samples from Arizona, Nevada, Chile, Australia, and South Africa were studied by differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). In addition, a sample from Miami, Ariz., was submitted to X-ray diffraction, infrared spectrophotometry, and surface area determination. EQUlPMENT Differential thermal analysis (DTA) detects, amplifies, and records exothermic-endothermic reactions occurring in a sample as its temperature is raised at a constant rate, usually 10°C per minute. A unit made by the Robert L. Stone Co. was used in this study. The tests can be run if desired with a gas streaming through the sample. A thermobalance records weight losses or gains in a sample as its temperature is raised at a uniform rate. The gravimetric analyses (TGA) were run on a Chevenard thermobalance converted electronically for graphic recording. A heating rate of 5°C per minute up to 1100°C was used in these tests. A Perkin Elmer Infrared Spectrophotometer, Model 221, was used with sodium chloride optics obtaining IR spectra in the 2 to 15 region. A pressed pellet technique with potassium bromide was used in preparing the samples. DESCRIPTION OF SAMPLES Chrysocolla is found in the oxidation zones of copper deposits commonly associated with malachite, azurite, and limonite. It is described as varying in composition and in color from bluish green to brown or black. Inclusions of other minerals are usual so chemical analysis of chrysocolla samples may be suspect. However, it is considered by many to be a solid solution of CuO, SiO2 and H2O with a general formula of CuO.SiO2.2H2O or 2CuO.2SiO2. 3H20. Chukhrov7 has described a sample from the Urals as CU3,5(OH)2 (A1Si3) O10.nH2O and stated that chrysocolla is a montmorillonite-type mineral. On the basis of X-ray analyses, DTA, and infrared spectra of chrysocolla from the Inspiration Mine, Ariz., Sun8 concluded that there was no substantial evidence to classify it as a montmorillonite mineral. Chrysocolla samples from many sources throughout the world were used in this investigation. The following is a brief description of each:

Jan 1, 1963

THE record of the development of physical metallurgy since the founding of this Institute embraces by far the greater part of physical metallurgy as this subject is recognized today. Yet it is not to be supposed that the metallurgist interested in the properties and behavior of solid metals at the beginning of this period was without important and even fundamental information. He had an empirical knowledge of the behavior of solid metals which extended backward into prehistoric times and he had the early beginnings of many of the chapters in the science of metals. Industry was burgeoning in many directions, for methods had been developed, especially in the manufacture of steel that provided materials in extremely large tonnages, permitting applications of metallic materials on a very widespread scale. These multitudinous new uses of metals created an increased interest in the behavior of metals, and provided the basis for the rapid development of a science of metals. Indeed, the development of science generally that accompanied the industrial revolution reached a flood tide toward the end of the century, furnishing the metallurgist basic principles in chemistry, physics, mechanics, and crystallography that would shortly be extensively applied to metallic behavior. In this account, the early developments in the wide metallurgical field will be traced, in order that the status of physical metallurgy in 1871, when this Institute was founded, may be clearly seen. The subject of metallurgy in antiquity has been written upon frequently and at length. We shall here no more than indicate the main features that we need to define the position in 1871 and to provide a proper background for discussing subsequent developments. The writings of Pliny,1 23-79 A.D., to which Robex-ts-Austen3 fre-

Jan 1, 1948

By D. L. Katz

The critical phenomena have been studied during the past century but our knowledge of the critical temperatures and pressures of complex hydrocarbon mixtures still is very limited. The critical temperatures and pressures of pure substances have been examined in large num-bers,20 and in great detail.11,17 No experimental determinations of the critical phenomena have been reported on such complex hydrocarbon systems as a reservoir fluid. The critical temperature is defined by Taylor18 as follows: "there is some temperature for each gas above which the gas cannot be liquefied. This temperature is called the critical temperature." The critical pres-sure of a pure substance is the vapor pressure at the critical temperature. It should be noted that these definitions refer to a given substance in the pure state and do not mean that the pure substance cannot be liquefied in the presence of a second constituent. The normal procedure for obtaining the critical temperature of a substance is to heat it in a glass tube 1,20 under pressure until the meniscus between the liquid and vapor phase disappears, although other methods, especially for mixtures, have been used. 11,14 However, when considering oil and gas reservoirs, it is more enlightening to consider a critical phe-nomenon that occurs when a mixture of oil and gas are compressed at a reservoir temperature until the meniscus disappears because the two phases become equal in composition. This conception, along with erroneous applications of the definition of the critical phenomena of a pure substance to that pure substance when it is part of a complex mixture, has caused confusion even among persons familiar with the classical theories.

Jan 1, 1938