Search Documents

By RAY J. CORFIELD

IN a previous paper, "Electric Shovel Operation at Utah Copper Mine," which was read before the Western Division of the American Mining Congress, the problem of electrifying a fleet of steam shovels was described. This paper deals with the electrification of the haulage system which, when completed, will make the mining operation completely electric, with the exception of drilling operations which will continue to be performed by air. The general layout of the haulage system involves the use of heavy curves in addition to heavy grades of between 4 and 5 per cent. In a mining operation of this kind no trackage can be called permanent; this complicates the overhead construction somewhat and makes it necessary to design special forms of trolley construction, some of which will be described in detail below.

Jan 1, 1929

By G. K. Manning, A. R. Elsea, C. R. Simcoe

It was found that a critical boron content exists which yields the maximum boron-hardenability effect in hypoeutectoid steels, as was predicted from the mechanism proposed in a previous paper. The hardenability of boron steels with boron contents between 0.00005 and 0.0017 pct was dependent on the boron content, austenitizing temperature, quenching temperature, and austenite grain size. The effects of these variables on hardenability can be explained by the mechanism previously proposed for the boron effect. A MECHANISM has been proposed to explain the effect of boron on the hardenability of steel.' The proposed mechanism assumes that transformation particles nucleate at concentrations of lattice imperfections where the energy level is high, and

Jan 1, 1957

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By R. B. Schluter, M. M. Fine

Processes for manufacturing prereduced pellets have heretofore required temperatures of 2100°F or higher. Sulfides will accelerate the liquid-phase sintering of metallic iron, yet do not deter the reduction of iron oxides. The sulfides may be introduced as gases to the kiln atmosphere or as solids in the re-ductants. The net result is that well metallized iron pellets with good crushing strength can now be produced at a little over 1800°F. One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. In May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.' More recently, in November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials at Evian, France, in May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then the current interest in reduction must be at a high level. Barrett,2 one of the early pioneers, stated some years ago that "The history of sponge iron has been so discouraging that many men in the iron and steel industry are violently opposed to giving it any further consideration." In spite of the "violent opposition" noted by Barrett, research people in and out of the industry continue to be attracted by the elusive prospect of uncovering a simple, viable means of direct reduction. Wild,3 one of the speakers at Evian, listed no less than 48 direct reduction processes (laboratory, pilot plant and commercial). Some of these were of historical interest only, but many others had resulted from developments within this decade. The previous big thrust into direct reduction occurred under the artificial impetus of a wartime economy (World War 11) and was largely an effort to provide more melting stock without coke ovens and blast furnaces. The present-day inquiry is proceeding at a more leisurely pace and the emphasis is different. For one thing, there is much less anxiety to circumvent the blast furnace. On the contrary, a whole new research endeavor has grown from the discovery that metallized burdens are exceptionally productive.4 Although the search for a melting stock

Jan 1, 1970

By Leon W. Dupuy

INTRODUCTION A BRIEF elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kind or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico 1-4 during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. SELECTION OF METHOD OF DRILLING Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. FACTORS GOVERNING SELECTION OF DIAMOND DRILLING The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1947

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By R. P. Dolan, W. M. Shedd, B. L. Buchanan

Analytical expressions are derived from empirical data relating the basic physical device parameters to the radiation dose. To put in perspective and justify the approach taken, the overall problem and methods of attempted solution of radiation damage to transistors in a missile or satellite environment is briefly examined. The main emphasis is on a new criteria for neutron radiation hardness and the device design implications resulting from using this criteria. Contrary to other derived criteria, the derived bipolar hardness relation depends mainly on the initial lifetime rather than the base transit time. It is shown, that contrary to previously accepted beliefs, the inherent attainable radiation tolerance of JFET's is at least a factor of ten greater than the radiation tolerance ofbipolars. Experimental results on JFET's designed for maximum neutron radiation tolerance are presented. The accuracy, utility, and range of possible validity of various published lifetime and carrier removal damage constants are discussed. It is well known that transistors are subject to damage due to radiation at much lower radiation levels than those which would cause structural damage to a missile or satellite. The three principal categories of radiation damage to transistors are displacement, ionization, and thermomechanical. The main cause of displacement damage is fast neutrons, and the main effects which permanently degrade transistor operation are minority carrier lifetime reduction and carrier removal. A second-order effect is mobility reduction. The main cause of ionization damage is gamma radiation which results in permanent effects due to charge build-up in the oxide and transient effects due to photo-current generation. The transient effects are usually handled by using circumvention techniques in the electronics system. The extent of the transistor degradation due to displacement and ionization damage depends strongly on the transistor type, whereas the extent of thermomechanical damage does not depend on the transistor type, but depends mainly on packaging and metallization which are common to all transistor types. The standard transistor types are categorized in Fig. 1 and typical cross-sections are shown in Fig. 2. The original reason for the designation of the two classes of transistors was that the unipolar operation depends on only one carrier (majority) and the bipolar operation depends on both minority and majority car- riers. The bipolar is then seriously degraded by minority carrier lifetime reduction, whereas the unipolar or field effect transistor is not. One of the two principle classes of field effect transistors, the junction field effect transistor (JFET), depends strongly on carrier removal. However, the insulated gate (MIS) is little affected by either carrier removal or lifetime changes, but is virtually eliminated as a radiation resistant device because of permanent charge build-up in the insulator caused by ionizing radiation. The bipolar and JFET suffer only minor effects due to charge build-up in the oxide passivation when compared1 to the MOS. This is because the active region of the MOS is adjacent to or part of the oxide layer. It is then the bipolar and JFET which are potentially resistant to permanent radiation damage. DERIVATION OF RADIATION TOLERANCE RELATIONS Criteria. The bipolar is by far the most widely used transistor type. The usual criteria for hardening bipo-

Jan 1, 1970

By George S. Evans

Certain American operators bclieve that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphuriza-tion will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Edward Schuster

As THE time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W, Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum" laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on . a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.1 Colombia requires foreigners to agree to be bound by its alien law. , In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. along its land

Jan 7, 1922

By C. W. Goodale

THE motives behind the organization of the Bureau of Safety were twofold. First, there was the policy of the company toward its employees, which was one of fairness and consideration for their welfare and which entails the prevention of injuries; second, in order to prevent injuries, a study of their causes was essential, and this study could be made only by a thorough systematic classification of accidents, which required a special department to form and carry out the plans. The Bureau of Safety was organized to begin operation Jan. 1, 1914, but practically all of the first year was spent in collecting data, making plans, etc. This department is semi-independent of others and reports directly to the president and general manager. It consists of the president of the company and the managers of the following departments: Mines, Washoe Reduction Works, Great Falls Reduction Works, Coal Department, Lumber Department, B. A. & P. railway, and the chairman of the Bureau of Safety. Working under this group is the General Safety Committee consisting of the manager of mines, as chairman, the general superintendent, two assistant general superintendents, and the heads of the following departments: mechanical, geological, purchasing, sampling works, and framing plant, as well as the safety engineer. Operating under the General Safety Committee are the group safety committees, consisting of the Anaconda group of mines, Boston & Montana group of mines, zinc group of mines,.Washoe reduction works at Anaconda, B. & M. reduction works at Great Falls, coal department, lumber department and the B. A. & P. railway. Each of these group safety committees was in charge of the superintendent or manager of the group represented and the committee consisted of the foremen of the mines or works that the committee served, as well as the safety engineer.

Jan 2, 1922

By George S. Evans

Certain American operators bclieve that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphuriza-tion will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Warren E. Wilson

PRESENT-DAY design of launders is essentially an art depending to a marked degree upon the experience of the designer, whose problem is that of determining the dimensions of a conduit that will transport the pulp within the physical limitations of the plant and in the most economical manner. This paper has been prepared in an effort to place launder design upon a more scientific basis. A method is developed from elementary principles and presented in a form that may be used directly by the designer in determining launder dimensions.. The equations that are developed are believed to represent an advance over older ones, in that they give due consideration to all the pertinent variables, either including them in the analysis or showing that they may be neglected within the limits of applicability of the equations. Experimental data from several sources are used in evaluating the coefficients that are not determined in the mathematical analysis. On the basis of the material presented, it is concluded that launders may be designed with a much greater degree of accuracy than previously believed possible, when due consideration is given to all the factors involved in the problem. However, a great deal of work still remains to be done in the laboratory before a complete answer to all the questions in launder design can be made available. HISTORY OF LAUNDER DESIGN Among the references1-11 are cited accounts of many experiments that have been conducted in an effort to advance the knowledge of the flow of liquid-solid mixtures in flumes and pipes. With three notable exceptions, this work was carried on in such a manner that the results have limited value in solving the general problem, since not all the pertinent variables were measured and controlled. The exceptions are found in the works of Blue,6 Gilbert,7 and Blatch,11 who exercised great care in controlling and measuring all the significant quantities involved in the experimentation. It is notable that much of the work done by men directly connected with the mineral industries1-4 lacks somewhat in completeness, owing apparently to preconceived notions concerning the factors that determine the flow. For example, many measurements on flow in pipes and flumes carrying liquid-solid mixtures determined only the slope and percentage of solids, with no mention of size of particles, depth of flow, roughness of channel or specific gravity of solids. Material in current handbooks8,9 and textbooks is based largely on the experimental work cited above. Although most discussions of the topic-include statements that the results to be obtained by using the data presented are limited by the fact that all variables have not been considered, it is

Jan 1, 1943

By B. S. Butler, H. D. McCaskey

The New London copper mine, about 8 1/2 miles east of Frederick, Md., was visited by the writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described by Gratonl and Laney,2 except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly the most important sulphide. In the New London occurrence calcite is the most important gangue mineral. Field relations The -town of Frederick lies in the center of a narrow belt of limestone ranging in age from Ordovician on the east to Cambrian on the west. This belt is about + mile wide at Noland's Ferry, on the Potomac, and broadens to a width of 3 miles at Frederick. The general direction is east of north. The eastern boundary is, in places, a fault plane along which a series of metamorphic rocks of presumptive pre-Cambrian age have been thrust up. These ancient rocks, for several miles east and west of New London, are phyllites in the main, but closely inter-folded near the New London mine are long, narrow lenses of epidote

Jan 1, 1915

By M. King Hubbert

DuRing the past summer the writer was asked by the Illinois State Geological Survey to make a study of some of its economic geological problems with regard to the applicability of geophysical methods of prospecting to their solution. The following four problems were suggested for investigation: (1) the fluorspar area of Southern Illinois, (2) oil structures in the south central part of the state, (3) the lead and zinc-bearing area of northwestern Illinois, and (4) the water supply and gravel deposits of the glacial drift. The prime requirements were to find a means of obtaining a maximum of useful information with a fairly modest outlay of expenditure for technical staff and equipment. The method of procedure adopted was that of making a preliminary study of each of the problems named by means of available office data and published reports with supplementary field reconnaissance where necessary. Preliminary Studies Fluorspar.—The fluorspar deposits of southern Illinois as shown by Weller,1 Bastin2 and others are of two main types: (1) vein deposits along steeply dipping normal fault planes, and (2) "blanket" deposits occurring practically horizontally along a certain sedimentary horizon. The vein deposits are composed mostly of calcite and fluorspar in sheetlike veins of thicknesses, where mined, ranging from about 2 to 12 ft. The surrounding topography is in a mature state of development with a relief of about 100 ft. or more. Any geophysical prospecting for this ore would have to depend either upon the physical properties of the ore and associated minerals or upon the properties of the geologic structure containing them. Fluorspar has a density of 3.18, which is somewhat greater than 2.7, that of calcite. Its

Jan 1, 1934

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

By C. G. Grant, Wm. B. Price

This investigation of low copper-nickel silvers was untiertaken to check the work of Lèon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the mierostructure of the binary alloys of copper arid zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Lèon Guillet evolved his conception of "fictitious compositions." He states,' in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds. For example, if a 60:40 brass has 4 per cent. of tin substituted for 4 per cent. of zinc, the actual composition would analyze 60:36:4. Assuming that 1 per cent. of tin plays the same part as 2 per cent. of zinc, the proportions of copper and equivalent zinc may be stated as 60 parts of copper and 44 parts of zinc, which, figured to 100 per cent., gives an analysis of 57.7 per cent. of copper and 42.3 per cent. of zinc, the fictitious composition for a 60:36:4 tin brass. The relation between ternary alloys containing copper and zinc together with a third metal, and the microscopically equivalent binary alloy of copper and zinc, may be expressed mathematically.

Jan 1, 1924

By E. H. Sellards

Phosphate rock like other mineral substances is found in nature in varying degrees of purity.

Jan 1, 1915