Search Documents

By G. Willard Quick

TENSILE tests of rail steels at elevated temperatures'' have shown that certain rails, in addition to having low ductility in the well-known bluebrittle range in the neighborhood of 200° C., have marked reduction in elongation and reduction of area in the temperature range from 400° to 700° C. This range of low ductility was called "the secondary brittle range" and the phenomenon, "secondary brittleness." The question naturally arises as to whether this property of the steels would be shown by impact tests performed in the same range of temperature. If so, the impact test, as suggested by Gillett3 would be a simpler and quicker method for the routine examination of steels at elevated temperature than the tensile test. A number of investigators have reported results of impact tests on steels at elevated temperatures, in which the energy absorbed decreased with increase of temperature above 200° or 300° C. Langenberg4 performed Charpy impact tests on several steels at temperatures ranging from room temperature up to 1000° F. (538° C). His results showed an increase in the energy absorbed in specimens tested in the range from room temperature to 200° or 300° C. and then a gradual decrease in the range, 300° to 538° C., the maximum temperature used. Greaves and Jones5

Jan 1, 1932

By Frederick Laist

While remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the Mac-Dougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide. The acid required for the operation of this plant will be purchased, ad the quantity required is not sufficient to justify the installation of an acid plant. An acid plant will, however, be established in con-

Jan 1, 1914

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By D. A. Summers, C. J. Haas, G. B. Clark, J. W. Brown

While significant advances have been made in excavation of rock, largely in improvements in drilling, blasting, loading, and haulage, conventional operations have been improved until little feasible increase in efficiency or rate of advance appears possible. Tunnel-boring machines have been developed which will excavate at rapid rates in soft to medium- hard rock. Hypervelocity impact is being intensively investigated as a possible means of cutting and breaking rock, as well as lasers, electric current, explosive drilling, high frequency vibration, etc. The current development and use of high-velocity small-diameter water jets, metallic jets, and projectiles of various materials involve ultra-high-pressure phenomena of fundamental interest. Rock disintegration by water jets has been investigated in the USSR for over a decade. Large-diameter jets of low velocity are used to mine coal, and high-velocity capillary jets will cut and break rocks under laboratory conditions. Velocity ranges for breaking and cutting are dependent upon rock and jet properties, and pulsed jets break some rocks more easily than continuous jets. Spectacular laboratory results have been reported for breakage of unconfined blocks of some types of rocks. Compressors, pressure multipliers, gas explosion chambers, and water cannons have been used to generate jets. Jet properties, such as continuity, unit pressure, total pressure, and stability have been measured. Results agree with theory, although the latter has been established only for relatively low-velocity flow. Diameter, speed of traversing, and frequency of pulsed jets affect rock response. Investigations in Britain have only recently begun consideration of harder rocks and higher velocities, although water jet cores have been found to be more continuous at lower velocities than previously believed. Lower limits of jet velocity for rock cutting were established for the rocks investigated.

Jan 1, 1970

By L. D. Hall, S. J. Rothman

The diffusion of lead and of trace amounts of bismuth in liquid lead have been investigated by the capillary method, using ROD and ROE as tracers. The results are compared with existing theories of diffusion in liquids, the agreement with theory being fair. The heat of activation for self-diffusion in lead is found experimentally to be close to the corresponding activation energy obtained from viscosity data. The pioneer data of Groh and von Hevesi for the self-diffusion of liquid lead, using ThB as a tracer, fit in with the present results. OMPARED with the volume of effort expended on solid state diffusion, there has been little attention paid to diffusion in liquid metals. A review of experimental work in this field, covering most of the studies up to 1951, was given by Jost.' More recent papers include those by Hoffman2 on self-diffusion in mercury, Morgan and Kitchener" and Stark, Shchilishchev, and Kazachkev4 on the diffusion of various elements in liquid iron, and Grace and Derge on the diffusion of bismuth in bismuth-lead alloys. The need for more experimental data to aid in the evaluation of existing theories prompted the

Jan 1, 1957

Jan 1, 1900

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By Anson Hayes, John Chipman

THE quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the British Iron and Steel Institute.1 From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. GENERAL THEORY OF SEGREGATION The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1938

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By W. Bonfield

A study has been made of the dislocation substructures produced in hot-pressed beryllium specimens strained to various levels in the range from 800 x 10-6 In. pev in. to fracture. A number of distinctive dislocation configurations were observed in this region which had not been noted at lower levels of strain. These included dislocation-dislocation interactions to form networks, dislocation "walls", subgrain boundaries and complex arrays, interactions between dislocations and large beryllium oxide particles, and the generation of dislocations from certain particles. The nature of these differences in substructure and their relation to the stress-strain characteristics of polycrystalline beryllium are discussed. In a previous study1 of the plasticity of commercial-purity, hot-pressed beryllium a transition was found in the deformation characteristics in the mi-crostrain region. The initial plastic deformation could be represented by a parabolic stress-strain equation, but above a critical stress there was a complete departure from this relation and a reduction in the strain-hardening rate. The dislocation configurations produced by various levels of micro-strain in this region were examined by transmission electron microscopy and a general correlation was established between the observed transition in deformation characteristics and the dislocation structure of the material. The two stages in the micro-strain region distinguished in these experiments were designated as Stage A' and Stage B'. Stage A' type deformation generally was noted up to a plastic strain of -80 x 10"6 in. per in. and Stage B' type from -80 x 10-6 to -800 x 10'6 in. per in. The discovery of two stages in the microstrain region naturally posed pertinent questions as to the existence of any further distinct stages in the subsequent plastic deformation. The purpose of this paper is to present a study of the dislocation configurations produced in similar beryllium specimens strained to various levels in the range from -800 x 10 in. per in. to fracture and to discuss the relation between substructure and the stress-strain characteristics. It is concluded that this region of strain can be considered as a distinct stage in the plastic deformation of polycrystalline beryllium. Tensile specimens of gage length 1 in. and cross section 0.18 by 0.06 in. were prepared from commercial-purity, hot-pressed QMV beryllium and then annealed at 1100°C for 2 hr. 2 followed by a careful chemical polishing procedure.3 The specimens were strained at a constant rate to various levels of strain in the range from -800 x 10-6 in. per in. to fracture (at 0.5 to 2 pct elongation), using the Tuckerman strain-gage technique1 to measure plastic and total strain. Thin foils were obtained from the strained and fractured specimens by chemical polishing3 and were examined using an RCA-EMU 3 electron microscope. Considerable care waS taken to avoid both accidental deformation during the preparation of the thin foils and excessive heating during their examination. Selected-area diffraction patterns were determined for each micrograph. Tilting experiments were also performed whenever appropriate to establish the dislocation zero-contrast position and hence determine the Burgers vector. This operation was sometimes not possible due to the rapid contamination of the foils which occurred in the electron microscope. RESULTS AND DISCUSSION To enable the distinctions between the dislocation arrays at high and low strain levels to be adequately made, the main characteristics of Stage A' and Stage B' deformation are briefly reviewed. 1) Stage A'. In the annealed starting condition there was a variable density (5 x 107 to 3 x 10' cm per cu cm) of isolated dislocations within a grain. The initial deformation in a tensile specimen was heterogeneous, with the dislocation density increasing in a few grains to 5 x 10g to 1.5 x 101° cm per cu cm. The deformation occurred exclusively on the basal plane by the movement of one or more 1/3 (1130) type dislocation systems. The dislocations were long and regular in form and nearly all the intersections exhibited a simple four-point node configuration. No interactions between glide dislocations and beryllium oxide particles were observed. 2) Stage B. In Stage B' there was a large increase in the number of grains exhibiting dislocation movement and also a change in the nature of the deformation, in which jogged dislocations and elongated loops became the characteristic feature. The splitting up of the elongated loops into smaller loops and the possibility of source action from the re-

Jan 1, 1965

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By R. B. Moore

Page History................................ 708 What is Radioactivity?........................ 710 Disintegration Series.......................... 711 Radium Ore Deposits......................... 713 Metallurgical Treatment........................ 717 Methods of Ore Concentration..................... 722 Future Supply of Ore......................... 723 Uses of Radium............................ 723 Mesothorium as a Substitute for Radium................. 724 Discussion.............................. 725 Probably no other metal excites as much interest, among both scientific men and the general public, as radium. This is due partly to the high cost of radium salts and partly to the peculiar properties of the element. Since radium-bearing ores were discovered in the United States, the interest of American scientific men has been stimulated and, at the present time, more radium is extracted and refined in this country than in all the rest of the world together. HISTORY The property of radioactivity was discovered, partly by accident, by Henri Becquerel, the French physicist, in 1896. He was experimenting with certain fluorescent substances in order to find, if possible, a connection between fluorescence and the recently discovered X-rays. Among other chemicals which possess the property of fluorescence, he was using salts of uranium. His custom was to expose the fluorescent substance to the action of sunlight and then register the effect of possible penetrating radiation on a photographic plate protected from ordinary light. Bec-querel's experiments gave positive results at once, and he at first believed that he had discovered a relation between fluorescence and X-rays. Later he exposed a plate to a uranium salt which had not been previously exposed to sunlight. To his surprise, on developing this plate, he found that he had obtained the same effect as he had previously secured when

Jan 1, 1919

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959

By M. Schwartz, S. K. Nash, R. Zeman

Knoop hardness in the rolling plane and in the longitudinal plane of hot-rolled and cold-rolled sheets of sublimed magnesiu?w was measured as a function of the angle between the long axis of the indenter and the rolling direction. These measurements were correlated with similar data taken on the (0001) and (1010) planes of a single crystal of magnesium where the hardness was measured as a function of the angle between the long axis of the indenter and the [1120] direction. The results were analyzed for compliance with the hypothesis of Daniels and Dunm to account for slip, and with a similar hypothesis to account for twinning. Some hardness anisotropy data are also presented for magnesium-indium and magnesium-lithium solid solution alloys. It is well known that the hardness of a crystalline specimen is different for its different surfaces, and also that the hardness is a function of direction within a single surface. Variations in hardness for single crystals have been found to be much larger than those for polycrystalline materials. Also, materials having low crystal symmetry were found to have a greater anisotropy of hardness than those of high symmetry. 0'Neill1 and Pfeil,2 using a 1-mm Brine11 ball, studied single crystals of aluminum and iron, respectively; and they found a variation of hardness of about 10 pct between readings taken along the principal crystallographic faces. Daniels and Dunn3 found that the Knoop hardness number varied about 25 pct as the long axis of the indenter rotated on the basal plane of a zinc single crystal. The variation on the (1450) plane was about 100 pct, and the average hardness on this plane was about twice that of the basal plane. They also studied the variation of hardness within the (loo), (110), and (111) faces of a single crystal of silicon ferrite and found variations of about 25 pct although the average values for these planes were almost identical. Single crystals of zinc were also studied by Meincke.4 He found that the Vickers hardness numbers varied about 30 pct depending on whether the axis of the indenter was parallel or perpendicular to the (1010) and (1110) planes. Mott and Ford,5 using a Knoop indenter, found a 25 pct variation in hardness on the basal plane of zinc. Crow and Hinsley6 studied heavily cold-rolled bronze, steel, brass, copper, and other metals. They found that the difference in hardness numbers based on the difference in the length of the diagonals of the Vickers indenter was from 5 to 12 pct. Some minerals and synthetic stones show a very large anisotropy of hardness. Robertson and Van Meter7 found the Vickers hardness of arsenopyrite to vary from 633 to 1148 kg per mm2. stern8 using the double-cone method on synthetic corundum found the hardness number to vary from 950 to 2070. And winchell9 reported a variation of hardness number from 184 to 1205 in kyanite. The variation of hardness as a function of direction in a given crystallographic plane in single crystals possesses a periodicity which is related to the symmetry of the lattice. Daniels and Dunn3 found a six-fold periodicity of hardness in the (0001) plane of zinc. They found that the hardness curves of silicon ferrite had a four-fold symmetry in the (100) plane, a two-fold symmetry in the (110) plane, and a six-fold symmetry in the (111) plane. Mott and Ford5 also reported a six-fold symmetry of hardness in the basal plane of zinc. And vacher10 found two-, four-, and six-fold periodicities of hardness in copper on the (110), (100), and (111) planes, respectively. The purpose of this paper is to report the results of an investigation on the anisotropy of hardness as a function of orientation in single crystals of mannes-ium, and samples of rolled magnesium, magnesium-indium, and magnesium-lithium solid solution alloys. The anisotropy of hardness of pure magnesium which had been hot rolled, and then cold rolled various amounts to fracture, was studied by means of Knoop indentation hardness numbers; and the results were correlated with the preferred orientation as determined by quantitative X-ray pole-figure data. A comparison was made of the hardness data obtained from the rolled sheets and those of single crystals of magnesium. In order to obtain a more fundamental understanding of the variation of hardness and of Knoop hardness testing, the data were analyzed by

Jan 1, 1962

By David B. Reger

The exhaustion of oil and gas in the United States is proceeding at a rapid pace. This is especially true in fields where the light oils that furnish the most fuel for internal-combustion engines arc found, leading to a late estimate by Arnold that the petroleum resources are 36 per cent. exhausted.l The further remark by Dr. David T. Day at the New York meeting of the Institute, in February, 1916, that the operators of the country are now scarcely able to supply the ever-increasing demand for gasoline, leads the writer to believe that a determined effort will soon be made to secure deeper producing horizons in those regions that now furnish high-grade oil, and in which pump stations and pipe lines offer convenient means for the economical handling of new production. A study of Arnold's table shows further that the States that produce paraffin oil exclusively are 45 per cent. exhausted, this figure being much higher than the average of paraffin and asphalt States altogether. The most extensive of all the paraffin-oil-producing areas is the Appalachian Field, extending with the Appalachian Geo-Syncline from western New York southwestward through western Pennsylvania, western West Virginia, Ohio, Kentucky, and Tennessee, where oil of high gravity is always secured. Of these States, Pennsylvania and West Virginia rank highest in the quality of their product. In West Virginia, the oil sands dip to a lower level than in any other locality in the Appalachian Geo-Syneline, the Pittsburgh Coal of the Pennsylvanian being only 50 ft. above sea level along the Nineveh Syneline at Wileyville, Wetzel County.² The very significant fact that the sands of the Mississippian and Upper Devonian Measures furnished the richest oil pools of the State along this

Jan 1, 1917

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith's latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith's latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940