Search Documents

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

By Ernest F. Burchard

MOST of the iron ore smelted in Alabama blast furnaces is mined within Alabama, although deposits in the neighboring States of Georgia and Tennessee may be drawn upon when occasion requires. Of the four commercial kinds of iron ore, the anhydrous ferric oxide, hematite (Fe2O3) ; the hydrous ferric oxide, mostly the type commonly known as limonite (2 Fe2O33H2O) ; the carbonate, siderite (FeCO3) ; and the magnetic oxide, magnetite (Fe:3O4) ; the first two are found in abundance in Alabama, the third in less than commercial quantities, and the fourth only rarely. Both the hematite and the hydroxide are found in somewhat different forms according to their geologic environment. The Red Mountain hematite, of Silurian age, that crops out in well¬defined beds for 1.50 miles northeast-southwest and 40 miles northwest-southeast is the predominant source of ore. Only a small part of this area carries ore of commercial value; Birmingham and Gadsden are now the only centers of production. The ore is of sedimentary origin, probably altered from vast deposits of greensand mixed with calcareous, fossiliferous. marine debris. Other types of hematite not vet mined commercially are in metamorphosed rocks-red ore in slates in Columbiana Mountain and specular hematite (gray ore) in quartzite in the Talladega Hills.

Jan 1, 1938

By L. R. Raymond, J. L. Hudson

This paper proposes a comparatively short-term (8 to 10 hours) well test for detecting and characterizing well-bore damage and for measuring mean formation permeability. The proposed test is made by injecting fluid at constant pressure, recording injection rate as a function of injection time. After one to four hours of injection, the well is shut in and fall-off of bottom-hole pressure is obtained as a function of shut-in time. Formation permeability is estimated by an iterative technique. First, a value of formation permeability is assumed. Then, a plot of the recorded injection rate as a function of dimensionless time is made, using the assumed pertneability value. From the slope of the injection-rate curve. a new value of formation permeability is calculated. If the new value agrees with the original assumed value, the assumption was the correct formation permeability. If the values do not agree, the process is repeated using the new permeability value in the calculation. Convergence is rapid, and a reliable permeability value results. Pressure fall-off data are used to check the result. Graphs of pressure and injection rate us functions of time given in the paper show that changes in permeability of the formation in the neighborhood of the wellbore are disclosed by this technique. Thus, the short-term test can he used to detect formation damage. Also, a rough measure of the radial extent of damage can be inferred, which is helpful in designing stimulation treatments. The mathematical model used for this work was a single-zone, horizontal reservoir with a damaged zone in which permeability decreased continuously as radial distance to the wellbore decreased. This model is more realistic than the usual two-zone, discontinuous permeability model used in published works; calculations indicate the realistic model is valid. Vertical variations in horizontal permeability were studied with this model, and results indicate that the permeability measured by the short-term test is the mean horizontal permeability for the vertical interval tested. The proposed short-term test thus should be useful in detecting and characterizing formation damage and in measuring formation permeability needed in calculating reservoir transmissibility. INTRODUCTION To plan the most efficient production or injection schedule for a well and to design or evaluate the optimal stimu- lation treatment, it is necessary to know the properties of the reservoir adjacent to the well, particularly the reservoir transmissibility and characteristics of a damaged zone, if one exists. Several techniques for determining reservoir transmissi-bility from well tests have been presented in the literature. 1,2,3,4 All these techniques rely on conducting constant-rate well tests that often are difficult to execute. A constant-pressure well test is generally easier to carry Out. and this paper contains the first available method for the analysis of constant-pressure well tests. Determination of wellbore damage from transient well tests has been the subject of several papers."" From these studies it is apparent that information necessary for determination of the characteristics of a damaged zone is available shortly after the transient well test is initiated. Consequently, it may not be necessary to carry out an extensive well test (for example, a pressure build-up test) if the primary purpose of the test is to detect the existence of wellbore damage. All previous studies of well testing to determine wellbore damage have been based on the two-zone perrneability model. In this model the damaged zone has a permeability k,, extending to a radius r,,, and the formation permeability k obtains from r, to the drainage radius r,.. Consequently, there is a discontinuity in permeability at r = r,,. This discontinuity can be eliminated by assuming a continuous variation in permeability through the damaged zone. The effect of this assumption on transient well tests is discussed in following sections of this paper. In addition, all formations have within them vertical permeability variations associated with lithology changes throughout the zone of interest. This paper also considers the effect of these variations on transient well tests. ANALYSIS OF CONSTANT-PRESSURE WELL TESTS The mathematical analysis associated with the injection of fluid at constant wellbore pressure into a single-zone, horizontal reservoir completely filled with a fluid of small and constant compressibility and constant viscosity is given in Appendix A. In this analysis it is assumed that the well is located at the center of an undamaged, circular drainage area. From this analysis, the formation permeability can be obtained as follows. 1, Estimate a value for the formation permeability k. 2. Prepare a plot of injection rate q vs

Jan 1, 1967

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By James V. Thompson

SINCE it was introduced in 1943 to recover chromite from Oregon beach sands, the Humphreys spiral concentrator has proved successful in several fields of wet mineral beneficiation. By the end of 1957, 9390 Humphreys spirals had been manufactured. Most of these are still in service. The spiral does not offer a panacea for all mineral dressing problems. Its proper application can best be determined by test work. Spirals present a unique advantage for the metallurgist to make tests in a full-size machine rather than a miniature model, without the risk involved in scaling up results. With only 10 to 40 lb of sample, the operator of a closed circuit test unit employing a full-size Humphreys spiral can conduct preliminary tests with full-scale loadings of 0.5 to 2.5 tph. With larger samples, from 300 to 500 lb, he can run longer multi-stage tests to obtain reliable data for the next step-pilot plant design. The manufacturer of the Humphreys spiral concentrator maintains a fully equipped ore dressing laboratory and by insisting on test work prior to sales has largely prevented misapplication of the spiral.

Jan 1, 1958

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn's temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Lang

The paper is a summary of information on Canadian deposits of uranium and thorium up to the end of 1948, prepared by geologists of Eldorado Mining and Refining Ltd. and by the specialist on uranium deposits for the Geological Survey of Canada. The paper contains a history of Canadian uranium and thorium discoveries, a working classification of the deposits, fairly detailed descriptions of the Eldorado mine and of properties in northern Saskatchewan, and shorter accounts of several other discoveries.

Jan 2, 1950

The Maas patent drill-hole compass, for determining the direction and dip of drill holes, is successfully used to a depth of 3,000 ft. APPARATUS FOR SURVEYING DEEP DRILL HOLES. The compass is placed in a thermos bottle or glass tube with hot liquid gelatine and lowered in a water-tight phosphor-bronze case, with a tube containing hydrofluoric acid. When the gelatine is cold the rods are pulled, the direction of the needle is marked on the tube which contained the acid, and the direction and inclination of the hole determined from this tube in a goniometer. There is nothing to get out of order and the compass can be used by any drill foreman, the mark and etching on the tube making a permanent record of direction and inclination. (See Fig. 1.)

Jan 1, 1916

By W. E. Pugh

The object of the following is to discuss a few of the problems encountered in the practical field application of reflection seismology. Very little has been published on this phase of the work and it is to be hoped that discussions will be presented by many seismologists who have met with these problems in the field. No attempt will be made to discuss the general principles of reflection prospecting, nor to outline the general field procedure. These phases have been presented more or less in detail in previous publications1 while economy of space and time prevents their being repeated or amended here. If, in the following pages, some criticism is offered of those who have already given their time and efforts to present valuable papers on reflection shooting, we trust that it will be accepted in the constructive light under which it is offered. We do not wish to give the impression that the following paragraphs represent ultimate achievement in field procedure; they are presented more to illustrate methods we have found satisfactory thus far. We believe that the following three subjects are inexorably linked with the continued future successes and more widespread use of the reflection method which, at the present time, is the most

Jan 1, 1934

By Herbert D. Drechsler

Mining Finance-is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm". The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance.

Jan 1, 1978

By C. H. Ferguson

The fact that little if anything has appeared in the technical press or in the Transactions of the Institute on the subject of roll shells proper, used in various grinding appliances…

Jan 1, 1915

By P. R. Schmidt, N. J. Themelis

A study zvas made of the deoxidation of copper at 1170°C by injecting a jet of carbon monoxide vertically upwards into the melt. The effects of submersion depth (2 to 20 cm), orifice diameter (& to 5 in.), and gas velocity (100 to 3650 ft per sec) were examined. In the oxygen range 0.1 to 1.0 pct 0, the overall rate was conlrolled by gaseoLcs mass Lransfer. The results were interpreted in terms of a rate coefficient per unit depth which was found to be constant with distance along the jet axis and nearly proportional to the orifice Reynolds number in the range 1000 < NReo < 9100. AS the gas flow rate through an orifice submerged in a liquid is progressively increased, at least three regions of bubble formation may be distinguished. At very low rates, the formation of bubbles is practically a static phenomenon, depending on the orifice diameter, the liquid surface tension, and the densities of the two phases. In this region, the bubble size is constant while the frequency of bubble formation increases with gas flow rate.&apos;-3 At higher flows (500 < NR~, < 2100), the frequency of bubble formation reaches a steady value and the bubble size increases with gas flow rate; when the bubbles issuing from the orifice become so large that they start coalescing to form larger bubbles, the turbulence induced in the liquid by the passage of previous bubbles shatters them into small bubbles of varying size. Finally, for gas velocities in the intermediate and turbulent regions of flow (NR,, > 2100) a tangential separation surface is created around the jet and momentum transfer takes place between it and the surrounding liquid medium. The entrainment of liquid and the resulting deceleration of the gas-liquid dispersion causes the jet to expand forming a characteristic jet cone. The large velocity and density differences between the jet and the liquid result in a high degree of instability and the jet envelope fluctuates rapidly.The characteristic jet cone can be observed by means of time exposure photographs such as those shown in Fig. 1 for an air jet introduced vertically upwards in a water bath. High-speed photography has showns that the gas-liquid dispersion within the cone consists of small bubbles the size of which depends mainly on the jet orifice diameter and Reynolds number. In the laminar region of flow, the following correlation was obtained by Leibson: The results of Liebson et a1.&apos; are plotted in Fig. 2. It can be seen that the region 2000 < NReo c 10,000 is not well-defined experimentally. In the entrance to the fully turbulent region of flow (NR,, = 10,000), the mean bubble diameter decreased to about 0.4 cm and varied only slightly from there on according to the correlation:

Jan 1, 1968

By E. R. Stover, J. Wulff

A tentative 870°C isothermal section, the solidus equilibria, and the solubility of Tic and graphite in the nickel solid solution have been determined with arc-cast specimens. Each of the Ni-Ti intermetallics forms two-phase fields with Tic; only Ti,Ni has a measurable solubility for carbon. A quasi-binary eutectic exists between Tic: and a titanium-rich nickel solid solution; ternary eutectics occur on either side, with TiNis or with graphite. Graphite is in equilibrium with a nickel solid solution containing a ratio of Ti/C which increases below the solidus. DURING the past decade, titanium-carbide cermets containing nickel or cobalt alloy binders have been widely studied for high-temperature and wear-resistant applications. Recent work has emphasized control of the carbide grain size and distribution2&apos;s and the thermal exparision match between the phases/ The present study was initiated to determine the phase compositions during the sintering or infiltration process, and during subsequent heating. Although the effects of additives and impurities in commercial compositions are important, it was necessary to consider first the pure ternary, Ni-Ti-C. Emphasis was placed on the nickel corner, since the nickel solid solution is the continuous phase in compositions having highest strength. Early metallographic work by Zarubin and Molkov- showed that solid solubility at either end of the section Ni-Tic is small. Edwards and Raine reported that nickel dissolves between 3 and 5 wt pct Tic at 1250° C, on the basis of microstructures of annealed, vacuum-melted powder mixtures. Although the solubility of nickel in Tic has not been measured, Tic formed by the menstruum process in liuid-iron solution contains as little as 0.06 wt pct Fe. BINARY SYSTEMS The most recent determinations of the three binary systems are summarized in Fig. 1. Titanium carbide (6) is predominant among the binary phases, and it melts above the boiling point of nickel. The Ni-C binary is based on separate liquid solubility&apos; ) and solid solubilitylo measurements. The eutectic temperature, 1328OC, is taken from the solidus determination described below. However thermal analysis data by Morrogh and williams also show eutectic arrests in this vicinity in the absence of supercooling. The Ni-Ti binary is taken from the work of Poole

Jan 1, 1960

By Cyril Stanley Smith, W. Earl Lindlief

A study of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published&apos; giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. Preparation of Allots The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 per cent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2 in. dia. cast-ing, the turnings being separated into three parts according to the position

Jan 1, 1932

The Climax design is for the human being and his needs. Climax President Arthur Bunker has likened the high mountain operation to a giant, 250 million tons in weight, and 12 thousand feet high. No matter how huge or complicated the plant, the design must assure efficient operation by its human operators. By the same token, living and playing facilities must be designed for fullest satisfaction in use-else the capital investment is not justified. Even the product, molybdenum, finds its application through the ever growing demands of a highly industrialized society of humans. Research in Climax Laboratories, in tune with our technical age, helps guide molybdenum to its maximum use for society.

Aug 1, 1955

By E. J. Krokroskia

Fletcher Mill is located in the southern part of the New Lead Belt in Southeastern Missouri, in the northwestern part of Reynolds County. Shaft sinking began in July, 1964. The mill went on stream in February, 1967, and reached the designed rate of 5,000 tons per day in July, 1968. The ore occurs approximately 1,000 feet below the surface as disseminated deposits of galena, sphalerite and chalcopyrite. There is no oxidation within the ore body and dissemination is not fine enough to present liberation problems with a normal grind. Mining is by the room and pillar method with rubber-tired diesel- propelled drilling and loading equipment. The ore is dumped through a 27-inch square grizzly into a 5,000-ton pocket. The underground primary crusher is automatically fed by a vibrating feeder and discharges directly into skip measuring bins. Hoisting is automatic, in balance, with 8. 5-ton skips dumping into a 1,000-ton mill bin. MILL The concentrator is a 5, 000 tons-per-day single section plant equipped to produce lead, zinc and copper concentrates. Contained under 35, 347 square feet of roof, without fine ore storage or remote crushing, and with sufficient automation to be operated by one man, the plant is compact, unique, and efficient in operation. The design

Jan 1, 1970

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By Lawrence B. Wright, Lester G. Morrell

ON the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest was evidenced in this district until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine [t] in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1938

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929