Search Documents

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By W. Mostowitsch, H. O. Hofman

The mineral gypsum, CaSO4 + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting-operations. Thus, in smelting oxide nickel-ore in the blastfurnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Preiberg, Saxony,1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. of Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term " blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating: is a happy generic term which covers the ground better than the " lime-roasting " of Ingalls5 or the " pot-roasting " of Austin: in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes—namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

Jan 1, 1893

By S. F. Emmons

This mine is situated upon the western slope of the Meadow Valley mountains, about 70 miles by road from the present end of the railroad-track, which is at Uvada, on the UtahNevada boundary. This boundary-line marks fairly well a certain change in type of scenery from western Utah to eastern Nevada,—from a region in which the desert valleys predominate over the mountain ranges to one in which they are in about equal proportion. The railroad from Salt Lake City runs somewhat W. of S., for the most part along the bottom of the ancient Lake Bonneville. The latter part of its present course follows the axis of the southern arm or bay of that lake, now known as the Escalante desert. Along this bay, its line is a mathematically straight one, with no perceptible change of level for two " tangents " of more than 30 miles each, varying but a few degrees in direction. In the four or five hours re-

Jan 1, 1902

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By W. R. Phibbs

THE Columbia Steel Corporation, organized in 1922, and taken over by the United States Steel Corporation on Feb. l, 1930, is operating one blast furnace at Ironton, Utah, which was started on April 30, 1924, and is producing approximately 14,000 tons of pig iron per month. Half of the pig iron produced is basic iron and is used in its own plants at Pittsburg and Torrance, Cal. The ore for the blast furnace is shipped from Desert Mound, Utah, near Cedar City, in the southern part of the' State, approximately 231 miles from Iroaton. The ore is a hematite, disseminated with magnetite, the chemical analysis showing approximately 12 to 20 per cent magnetite, and under the micro- scope the ore has the appearance of a magnetite.

Jan 1, 1930

By Carl G. Schwenk

Rocks of the Precambrian Shield of Rusk County, Wis., were recognized as a favorable host for volcanogenic base metal deposits by personnel of Bear Creek Mining Co. Most of the county is covered by a thick layer of glacial drift: consequently, geophysical techniques played a prominent role in the exploration program conceived and initiated there in 1966. The original work on three Precambrian exposures was followed by an airborne electromagnetic survey and subsequent ground follow-up. A geophysical evaluation of air-borne anomaly F-22 defined a target which was interpreted as a massive sulfide body. Numerous potential field and electrical tools were utilized to describe the geometry and physical properties of the target. Drilling confirmed the massive sulfide interpretation and eztentually outlined a 6 million-ton copper deposit.

Jan 1, 1977

By Robert Peele

TWO outstanding members of the Institute will be honored at the Annual Meeting this month: Robert Peele, who will accept his election to the small group of Honorary Members; and Clinton Hoadley Crane, president of the St. Joseph Lead Co. and William Lawrence Saunders Medalist for 1936. Eminence in the profession character, interest in Institute activities, and general recognition as a gentleman and a friend by so many people, have contributed to the election of Professor Peele. The Saunders Medal is for "achievement in mining." In awarding it to Mr. Crane the citation reads "For distinguished achievement in the successful development and operation of low-grade lead mines."

Jan 1, 1936

By R. H. Rice

Turbo blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting.

Jan 1, 1915

By N. Jaffe, J. E. Dorn

This investigation is concerned with the possibility that the creep resistance of metals might be reduced as a result of recovery at the creep temperature when the applied stress is reduced. For this purpose the effect of stress on the recovery of the creep behavior of pure polycrys talline aluminum was investigated in the cross-slip temperature range where the activation energy for creep is 28.000 cal per mole. Before recovery all specimens were given the same substructure by creeping them under a stress of 7800psi to a strain of 0.218. Recovery was then accomplished by holding the specimens at the creep temperatures of 327" and 337°K under a series of reduced stresses for various periods of time. When the original stress was reapplied the specimens crept more rapidly than when the original stress was first removed, illustrating that recovery did take place. The extent of recovery could be indexed in terms of the UNDER certain conditions of test, the creep rate decreases over the primary stage of creep often by as much as a factor of 10~B. Since the external variables of stress and temperature are held constant, such pronounced and significant changes in the creep rate must be attributed to various substructural modifications that are introduced as a result of creep itself. At the secondary stage of creep, over which the creep rate remains constant and the substructure no longer changes, a balance must be achieved between the rate of increase in creep resistance due to creep straining and the rate of recovery of the substructural modifications. The general validity of these concepts on substructural changes has already been shown,' including the corollary that a more creep-resistant substructure is introduced under a more rapid creep rate arising from a higher applied stress.' In spite of these well-documented facts, very little progress has been additional strain undertaken by the recovered specimen to achieve the same strain rate as the unrecovered specimen. It is significant that the higher recovery stresses gave the most rapid rates of recovery. Over the high range of reduced stresses, where some creq took place during recovery, the activation energy for recovery equaled that for creep, namely 28,000 cal per mole. But for stresses during recovery below 0.80 of the original creep stress, no creep was detected during recovery and an activation energy for recovery of about 72,000 cal per mole was obtained. Whereas the activation energy of 28,000 cal per mole suggests that cross-slip of dislocations is responsible for this recovery, the mechanism for the 72,000 cal per mole process is not known. This activation energy, however, is about twice that for self-difhsion. made in determining, in satisfactory detail, precisely what substructural changes so effectively modify the creep rate.' Up to the present, electron microscopy has failed to uncover, in a satisfactory quantitative manner, the mechanistic processes involved. Since, however, creep, at least at moderate and high temperatures, arises from one or more types of dynamic recovery processes, it should be possible to shed additional light on the total problem by investigating the recovery of creep resistance. The importance of such an investigation becomes apparent when the fact is recognized that there has yet been no direct experimental proof that the rate of softening due to substructural changes as a result of recovery equals the rate of hardening due to creep-induced substructural strengthening over the secondary stages of creep. Furthermore the problem of what happens to the creep-strain induced strengthening when the material recovers either at zero or some reduced operating stress has significant engineering consequences. It was for these reasons that the present investigation on the recovery of creep behavior was initiated. Inasmuch as a substantial background has now developed on the creep of high-purity aluminum, this material was again selected for the current investigation. Furthermore extensive evidence is now

Jan 1, 1963

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-'has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.' to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

By K. B. Nowels

DATA pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Uren1 presented some findings based on laboratory experi-ments in which vertical flow of an extremely heavy crude oil was induced, by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another. valuable contribution pertaining to the problem, of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference .has been made.

Jan 1, 1932

By E. O. Chartkoff

IN 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,1 including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Measurements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic compound phases upon sintering a mixture of metal powders.

Jan 1, 1930

By C. L. Bulow

In this discussion of stress-corrosion cracking of widely used copper-base alloys, no attempt has been made to prepare an extensive review or bibliography since this has been quite ably covered by other investigators. An excellent bibliography was published by H. P. croft(1)2 in connection with his studies of stress-corrosion cracking in mercurous nitrate solutions and his analyses of the magnitude and distribution of stresses in brass parts. We are reporting on a few of the results which have been obtained to date in connection with an ammonia vapor test and an alternate immersion test. These are accelerated corrosion tests for determining the susceptibility of materials to failure from season or stress-corrosion cracking due to the presence of moist ammonia and oxygen so prevalent in nature. Our experiences with the ammonia test seem to indicate that it is a more searching test, than the mercurous nitrate test.

Jan 1, 1945

By K. F. Veith, R. L. Marovelli, T. S. Chen

An analytical study is made of thermal stress distribution in a thin circular disc subjected to a peripheral thermal shock at various rates of heat transfer. The problem is of importance in predicting the thermal shock response of a rock body of finite size. The theoretical analysis is based on radial heat flow by conduction in the disc and heat exchange by convection between the disc and the surroundings. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks and an average stress theory is formulated. Preliminary experimental verification was obtained from the results of shock tests on thin rock discs insulated on both flat end faces so that heat exchange took place through the exposed peripheral surface. Physical properties vital to the analysis are Young's modulus, tensile strength, coefficient of linear thermal expansion, thermal diffusivity and thermal conductivity. Plots of these properties are presented. Historically, thermal energy has been used for primary rock removal throughout the ages. Although it is not widely known, the fire-setting method of thermal rock fragmentation was still in use 100 years ago in systematic underground mining operations in Scandinavia.' There, the availability of cheap labor and abundant wood fuel made the method competitive with the early blasting powders. By 1880, as high explosives replaced powder, use of the method declined and it was finally abandoned about 1885. Only 40 years ago, some experimental fire-setting methods were used for rock removal underground at Pribram and Zinnwald in Central Europe.2 Compressed air-oil burners replaced the earlier wood fuels. About 15 years ago, gaseous oxygen-oil burners were introduced in the United States and gained acceptance for difficult blasthole drilling and some quarry opera- tions. At present, there is renewed interest in the compressed air-oil burner designs. The literature included information on thermal secondary processes for rock weakening or particle liberation3,4,5,6,7,8 on thermal spallation of rock 9,10,11,12,13 and on the thermal fracture of materials other than rock. The 1955 Symposium on Thermal Fracture14 and the later work of Hassel-man, cover recent developments in thermal shock investigations on brittle ceramics. Although the number of published analytical and experimental investigations conducted on ceramic and refractory materials is large, the literature reveals that there is a lack of information on both the theoretical and actual response of rock to thermal shock. Many of the thermal shock studies on ceramic and refractory bodies are based on the case of heat transfer at the solid's surface by convection in either liquid or air. A similar heat transfer situation was adopted for a theoretical analysis of the thermal stresses in a thin circular disc subjected to a peripheral thermal shock. Experimental thermal shock tests were then conducted on rock specimens to check the analytical results. Specially insulated quartzite, basalt and taconite discs were shocked in either liquid or still air bath at various rates of heat transfer. The work was done in order to resolve the question as to whether theoretically determined tensile stresses are actually realized in a finite rock body undergoing thermal shock. Specifically, if theory predicts that the tensile strength of a rock should be exceeded in a particular type of controlled thermal shock, will fracture occur? This information is needed by Bureau researchers working on thermal and electrical rock fragmentation methods. The object of this paper is to present the main features of the theory and procedure being used in the authors' approach to quantitative prediction of rock response to a thermal shock. THEORETICAL ANALYSIS In the analysis to follow, simple geometry of a thin circular disc is considered. The disc is assumed to be isotropic, homogeneous and perfectly elastic, and to have constant thermal and mechanical properties. The effect of radiation is neglected so that heat is transferred by conduction inside the disc and by convection with its surrounding. In addition, the end

Jan 1, 1967

By T. B. Counselman, T. B.

Continuous countercurrent decantation calculations have always been a headache to the cyanide man (and the chemical engineer) because of the simultaneous equations involved. These are tedious to solve, and there is considerable opportunity for mathematical error. This paper presents a shortcut method for making these calculations, which has been in successful use for twenty years by the author, and which is particularly valuable in selecting the best of several possible flowsheets, or evaluating the effect of various assumptions.

Jan 1, 1950

By Frederick Apgar

(Butte Meeting, August, 1913.) THE valuable results that have followed the application in recent years of microscopic methods of research to problems of ore genesis have been significant, but possibly the recognition of their practical importance is not as general as might be, and while, as a scientific method of investigating ores and rocks, the advantage derived through the use of the microscope is unquestioned, its utility as an aid in solving shining problems arising during actual every-day mine examination and operation may not be fully appreciated. Perhaps the roost logical method of showing some of these practical applications of the microscope will be to consider first the prospect stage of a mining venture, then the uses to which the instrument may be put during the operation of a working and developed mine, and, finally, to discuss some of the problems of a metallurgical nature that ii-my arise during milling and smelting the ore. The valuation of mining property as a preliminary to acquiring ownership or determining the advisability of investing time and money in an enterprise is one of the most important and delicate problems that come before the mining engineer. The many and variable factors that have to be taken into account, as, for example, the geology of the district, availability of supplies, probable mining costs, transportation facilities, and the quality of ore, require a careful balancing of costs against recoverable values.

Jan 6, 1913

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential, but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for converting a prospect into a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is usually headed by an engineer-promoter or an entrepreneur trader who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the ha1 operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1964

By McQuiston. F. W., E. C. Tveter

Sulfide mineral flotation has been applied to all naturally occurring sulfides and several synthetics. Of even more importance is the fact that economic separations are now being made between sulfides of essentially all the different metals. The variety of methods and minerals involved in such practice make it difficult to characterize them except in terms of general factors which influence the practices used. Ore grade and mineral composition are the major factors determining the processing method and the extent to which processing must be carried to achieve optimum economic return for a given ore. Since the choice of treatment is also affected by such factors as mine location, shipping charges, smelter schedules, each ore is a separate problem even though mineralization may be similar; The dissemination of minerals in the ore naturally determines the fineness of grind required for liberation. However, since grinding costs are a major part of most milling costs, emphasis has been placed on means of rejecting gangue minerals at the coarsest size possible. This has led to increased flotation of middling products or bulk concentrates for subsequent regrind and retreatment. Reagent development has also played an important part in present plant practice. Relatively few new frothers and collectors have found application during the past 25 years and many have disappeared. In general practice, re- agent combination choice is now fairly consistent with the type of collector being chosen on the basis of the mineral to be floated, the frother on the basis of pulp alkalinity, and the modifiers primarily on the basis of minerals to be rejected. REPRESENTATIVE FLOTATION PLANTS The milling operations described in this chapter have been selected primarily to illustrate these differences in ores and processing methods for the major types of ore minerals. The compositions of these minerals are shown in Table 1. These concentrators were chosen as representatives, both on the basis of geographic location and mineral content of the ore treated. At least one mill is included from each of the major producers, but the primary object was to show the practice employed for the various ore minerals and the different approaches to the middling problems encountered. The individual plants which have contributed data to this study are listed in Table 2, with a summary of their operating data, and are discussed in the order shown.

Jan 1, 1962

By Robert Mehl

THE precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstätten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe,P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. PRECIPITATION OF FE4N FROM ALPHA SOLID SOLUTION OF N IN ALPHA FE Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kaupp1 and by Lehrer2 have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591° C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934