Search Documents

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

By D. F. Hewitt

Page Introduction..............................305 Geologic features of eastern Oregon....................306 Geology of the Sumpter quadrangle....................306 Rocks older than the ore deposits...................307 Rocks younger than the ore deposits.............. . Lodes of the Sumpter quadrangle..................312 Areal distribution.......................312 Geologic distribution.................... . Major features of the veins...................313 Mineralogy and texture of the veins.............. . Ore deposits zonally disposed around the Bald Mountain batholith . 317 Summary of mineralogy and texture.............336 Zonal relations......................337 Ore deposits zonally disposed around Greenhorn Mountain batholith. 340 Zonal relations..................... . Relation of textural features to zonal arrangement of veins.....341 Summary of zonal relations.................. . Comparison with similar districts................. . Outlook for the district......................344 Introduction In an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.' It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt' reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements' are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases' and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of' the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By William G. Kegel

Aside from having a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in acquiring this is the presence of good mechanics-men who have a desire to be mechanics and who want to know more about the design and control of the machines in their charge. The knowledge and ability to be found in a good mechanic is the result of ambition, curiosity, and determination. With these qualities as a start, the aspiring mechanic can launch his career if he begins learning all he can about mechanics, electricity, and hydraulics. The path is rough, but the goal is rewarding. Mining machinery probably absorbs as much or more abuse than any other heavy equipment in use today. And when one considers the conditions under which much of the repair work must be done, it can be seen that the mine operator needs the best of men and tools to perform the service. MOTORS AND POWER SUPPLY Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were large, heavy-framed, open d-c motors (direct current), using a series or shunt winding. A motor having one or more field coils connected in series and themselves in series with the armature, is called a series motor (Fig. 1). The series motor had the advantage of quickly developing starting torque, and it was, and still is, the best motor for locomotive or shuttle car tramming service. The series motor, however, speeds up as the load is reduced and, if not properly controlled, can overspeed. The shunt motor, as its name implies, has one or more field coils in

Jan 1, 1973

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By F. R. Hensel

THE demand for clean steel is increasing daily. New processes of refining steel are being developed in order to remove all nonmetallic inclusions as completely as possible, as it is the general opinion that. inclusions affect the dynamic properties of steel and iron to such an extent as to justify great expense for their removal. It is surprising to note at the same time the commercial development of a new process for making artificial wrought iron. By this process slag and steel are thoroughly mixed, the amount of nonmetallic inclusions usually exceeding 2 per cent in weight. The contradiction in these two efforts is obvious and is responsible for the investigation reported in this paper. H. W. Gillett also has recently emphasized the need for further research on wrought iron.1

Jan 1, 1932

Jan 1, 1884

By J. J. Beeson

The second part of the paper includes a detailed account of the processes of secondary-enrichment which have been effective in producing the disseminated ores. While both parts present new features, it is hoped that the discussion on secondary chalcopyrite and bornite may be of interest to those who are engaged in the study of secondary processes in other districts. The excellent work' Economic Geology of the Bingham Mining District, by J. M. Boutwell, was published in 1905. Since that time the extensive development work-surface cuts and underground drifting-of the Utah Copper Co. has made possible the collecting of samples for more detailed microscopic study. The writer has taken advantage of this fact and presents the following work, not as a criticism, but as a' continuation of the work which was begun by Mr. Boutwell. b. Acknowledgments.-The present study was undertaken at the suggestion of Dr. A. F. Rogers; to him, and to Prof. C. F. Tolman and Prof. S. W. Young, the writer wishes to express his thanks for criticism in the preparation of this paper. The writer also expresses his thanks to D. C. Jackling, Vice-President and Managing Director of the Utah Copper Co., for permission to publish this paper, and to William Spencer, D. W. Wadleigh, T. S. Carnahan, J. A. Caulfield, Percy Dayer, and Edward Norsefall, for the courtesies extended to him while a co-worker in the mines.

Jan 11, 1915

By R. Van A. Mills

ONE of the most important problems facing the petroleum industry is the profitable recovery of oil that is left underground by the ordinary methods of production. It is true that vast quantities of oil are being recovered from fields previously considered depleted by the pressure restoration method, the most widely applicable -and most successful means of obtaining greater recoveries that has thus far been, developed. But notwithstanding the progress that is being made in the field applica¬tion of this method there is urgent need for a better understanding of the fundamental principles that are involved. To meet this need the Petro¬leum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., during the past two years has conducted a series of intensive laboratory and field investigations. The larger part of the work has been carried on in the laboratory to supply the much needed information upon fundamental principles, information which few if any of the oil companies are in a position to supply for themselves. In all of this work the Bureau is endeavoring to correlate the results of laboratory investigations with those in the field, using the results of one to guide or check the other. This paper is primarily a progress report, briefly outlining the Bureau's methods of study, the laboratory and equipment in use, the preliminary problems that had to be solved in order to attack the major problems at hand, the methods of attacking some of the major problems, and some of the results of the investigations to date.

Jan 1, 1928

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

By C. H. Mathewson

MICROSCOPIC. rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of 'particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By W. R. Crane

MINING of the red iron ores of the Birmingham district has been carried on energetically during the past 50, years, and their development has created a large iron and steel manufacturing, center, the only important one in the South. The district produces approximately 10 per cent. of all the iron ore of the United States (80 per cent. of the Alabama ore mined is red ore) ; also, 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham. The rapid growth of the district has been made possible through investigations that resulted in radical changes in furnace practice, and a still greater impetus will come from the study of the low-grade, high-silica ores, as a result of which they will be made amenable to treatment by concentration. Mining practice in this district has been comparatively simple because of the occurrence of the ore; but with the-rapid extension of the work-ings and the disturbed condition of the ore bed at some distance from the outcrop, more difficult conditions are encountered and the tendency is toward worse rather than better conditions. Should the high-silica ores of the lower bench of the Big Seam become available through beneficiation, mining practice will have to be modified to meet the new conditions, which will be rendered more difficult by the increased weight of cover that will exist at considerable distances from the outcrop. Support of workings will require greater attention and the efficient and economical operation of the mines will depend largely on the successful solution of the problems of working-and handling the ore.

Jan 9, 1924

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage,-and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation. INTRODUCTION Cornucopia is in the southeastern part of the rugged Wallowa Moun-tains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal.

Jan 1, 1939

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By John T. Eash, Clair Upthegrove

During recent years nickel has had an increasingly important role as an alloying element in the copper-tin bronzes. Nickel additions not only produce better casting alloys but also make alloys whose properties can be varied by precipitation hardening; thus leading to increased commercial application of copper-nickel-tin alloys. Recent investigations have indicated a decrease in the solubility of tin in the alpha phase as the annealing temperature is lowered and as the nickel content is increased within certain limits. A further change caused by the nickel additions is produced in the excess phase of the copper-tin bronzes. The alpha plus delta eutectoid is replaced by a clear precipitated constituent in the alloys containing up to 15 per cent tin and not less than 1 per cent nickel. This paper has a dual purpose. The first is to present a new determination of the alpha-phase boundary in alloys containing from 0 to 20 per cent nickel, together with the liquidus and solidus temperatures above that field. The second purpose is to give the equilibrium conditions existing in alloys exceeding the alpha phase containing up to 31 per cent tin and 5 per cent nickel, so that the disappearance of the alpha plus delta eutectoid constituent may be explained. After considering the earlier investigations of the related alloy systems and the experimental procedure used in this investigation, the alloys will be discussed in groups as separate quasibinary systems containing constant amounts of nickel. The systems considered contain 0, 1, 2, 3, 5, 10 and 20 per cent nickel. The straight copper-tin system was reinvesti-gated in order to establish a foundation on which to build the remaining material. The 1 per cent nickel alloys studied give the relations existing in the region of the eutectoid transformation between the copper-tin system and the 2 per cent nickel copper-tin system which has been investigated in detail. The thorough examination of the latter system was made since 2 per cent of nickel is representative of the commercial additions to the cast bronzes and also because it is sufficient to produce

Jan 1, 1933

By Henry M. Howe, Joseph Winlock, Francis B. Foley

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923