Search Documents

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By S. G. Shabestari, S. Saeidinia, P. Mokarian

"The experiments were conducted to investigate the influence of various process parameters in rotary degassing of aluminum alloy AS5U3G. Degassing was carried out by use of argon inert gas. The flow rate of the gas was investigated in the range of 12 to 21 L/min., 350 to 500 rpm rotor speed, 6 to 12 minutes degassing time, and 755°C to 780°C melt temperature. Degassing efficiency was evaluated through measuring the density of RPT samples. By optimizing the process parameters, RPT sample density was increased up to 2.73 g/cm3, which guaranties the production of high-quality aluminum castings. Tensile strength and elongation were increased considerably by degassing process. Scanning electron microscopy (SEM) shows small size and well-distributed microporosity. IntroductionOne of the major problems associated with the casting of aluminum alloys is the formation of gas porosity. Aluminum and its alloys are very susceptible to hydrogen absorption. Because solubility is much lower in solid state than liquid state, hydrogen atoms leave their position during solidification and combine together to form hydrogen molecules. These micrometer- scale cavities, called microporosity, cause the reduction of mechanical properties, particularly strength, ductility, fracture toughness, fatigue resistance, pressure tightness, and corrosion resistance (Laslaz, 1991; Jorstad and Rasmussen, 1993; Sigworth and Wang, 1994; Korasani, 1996; Anson and Gruzleski, 1999; Zhang et al., 2000). To avoid these problems and produce good quality castings, it is necessary to remove hydrogen from the melt. Several methods are available for degassing aluminum melt. One of them is a rotary degassing system using inert gas, e.g. Ar or N2. Various thermodynamic and kinetic factors govern the removal of hydrogen from molten aluminum (Anderson, 1987; Sigworth, 1987; Pignault, 1993; King and Reynolds, 1995). These are some parameters that affect degassing efficiency. Some of them are discussed here and some are examined in this project."

Jan 1, 2004

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By P E. H Gregg, D Horne, R B. Stewart, N Bolan

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100 000 mm of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity inNew Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.   The suitability of the tailings as a potential plant growth medium was assessed with the end view of revegetating the tailings dam and alleviating AMD. This paper outlines characterisation work conducted on the tailings and summarises preliminary results from plant growth trials. The tailings contain up to 5% Fe, 1.15 % Pb, and 0.45% Cu in the form of sulphide minerals. The distribution of heavy metals, sulphate and total sulphur with depth indicates that the top 200 - 300 mm of the tailings have been extensively weathered since their deposition. The oxidation of sulphide minerals, particularly pyrite (FeS2 ) has reduced the pH of the tailings to nearly 2 in places. Below 300 mm the sulphide minerals are largely unweathered and the theoretical acid generating potential of the tailings exceeds 170 Mg CaCO3/1000 Mg tailings at certain depths. Plant growth trials were conducted to study the effects of lime and organic matter addition on the establishment of vegetation on the Tui mine tailings. Several plant species were assessed including some cultivars bred for their tolerance of heavy metals.

Jan 1, 1995

By Bukeikhanov D. G, Syedin V. F, Sagyngaliyev K. S

The present paper describes a method of simulating deposits of com- posite structure by means of computers. The method employs mathematical tech- niques to study the openworks zone formation dynamics in open-pit mines with any mode of the works front ad- vance as well as to determine, on oriented graphs,the optimal direction of openworks expansion.

Jan 1, 1977

By Steve Kral

Worker safety is an issue that transcends industries, whether it be mining, construction, manufacturing or even general office work. In the mining industry, safety and training are particularly important because mining is a dangerous occupation. Throughout the years, federal and state safety regulations have been written and revised to keep up with the changing technologies. And mine operators have installed their own safety and training programs. They have come to realize that a safe and healthy workforce has positive effects on productivity and profitability —not to mention avoiding the high costs of injury-related absenteeism.

Jan 1, 2003

By R. G. Horvath

The Statnamic loading test is a new and innovative method for testing deep foundations. The test is relatively inexpensive, quick, easily mobilized, provides for direct measurement of applied load and corresponding displacement, and is capable of very high loading capacities. The long duration of the applied loading, as compared to a dynamic loading test, allows for a straightforward determination of the static behaviour of the foundation tested. A new method of analysis of the Statnamic loading test, the Equilibrium Point Method, is presented. A description is given of the pile-soil model and a demonstration of how the static load-displacement behaviour of deep foundations may be predicted from the Statnamic loading test data. The Equilibrium Point Method of analysis is applied to three types of deep foundations in soils which respond differently to fast loading rates. These case histories, from Canada and the United States, include data from static loading tests for direct comparison, and demonstrate the ability of the Equilibrium Point Method to predict static behaviour of the deep foundations.

Jan 1, 1993

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Otago Schist belt of southern New Zealand hosts widespread orogenic gold deposits. Erosion of these orogenic gold deposits has led to the formation of numerous placer deposits distributed across and beyond the host schist belt. Numerical modelling of crustal scale deformation and geomorphic evolution has defined the key tectonic features that have controlled the severance of detrital gold deposits from their sources. Tectonic activity over the past 20 million years, during development of the modern Pacific-Australian plate boundary, has severed links between some placers and their sources. Detrital gold was transported south from the Otago Schist source region in two different river systems in the Miocene. Mesozoic orogenic gold deposits shed gold into rivers that flowed to the south. These rivers were terminated by the rise of north-west-trending basement ridges at the boundary between weak schist crust and strong greywacke crust, and the ridges were controlled by pre-existing faults at that rheological boundary. In contrast, rising mountains close to the developing plate boundary in the Miocene were the locus of new orogenic gold deposits hosted in extensional faults. These gold deposits were rapidly exhumed and contributed detrital gold to orogen-parallel Miocene rivers that flowed to the south-west. Pleistocene deformation on mainly north-west and north-east orientations, and associated river capture, has severed the links between these Miocene orogenic deposits and downstream detrital gold.CITATION:Craw, D and Upton, P, 2015. Tectonic severance of links between placer gold and its sources, southern New Zealand , in Proceedings PACRIM 2015 Congress, pp 541–544 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By X Qiu

According to the temporal and spatial distribution of regional metallogenesis, thePacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinental metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly related to S-type granite of crustal source that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of mineralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metallogenetic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

Roasting of a Copper Sulfide Concentrate

Sep 13, 2010

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010

By P M. Ashley, M Muller

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of north-eastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe land sliding in previously mined areas. Mining from the 1890s to the 1960s has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002