Search Documents

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimize the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focused on ore characterization and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blast ability indices, as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined, a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model; however, it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained, thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. Additionally, the initiative has benefited both brownfield and greenfield projects on the PPRust operation

Jan 1, 2006

By Sachihiko Tokunaga, Hirofumi Taguchi, Kenji Maruyama, Hidenori Takahashi, Yoshiyuki Morikawa

"Abstract The present study proposed a new liquefaction countermeasure to improve sandy ground and conducted a trial execution. The new method is a floating-type and lattice-shaped cement treatment method, where cement-treated soil is not fixed to a non-liquefiable stratum. A fixed structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were first conducted to confirm the mechanism of the new method. Then, a series of centrifuge model tests were performed to demonstrate the effect under a stress condition at the prototype scale. The analyses and model tests confirmed the effect of the liquefaction countermeasure. Finally, trial executions were carried out to confirm high-quality vertical execution.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. In particular, the cost of the high-pressure jet mixing method, which can be applied to the liquefiable ground under existing structures, is significantly high. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2014

By D. Schleiss

Reduced access to knowledgeable workers is creating challenges for operations. We are doing more 4D Operations - dirty, dull, dangerous, and distant. Personnel costs in these environments are high, and it is not always possible to get the people where you need them. Integrated Operations is a strategy to integrate people, process, and technology for faster and better decision making. Adopting an integrated operations approach can help to relocate personnel, improve collaboration, and align objectives to deliver reduced costs and improved performance. In this paper, the authors will highlight the required infrastructure to enable an Integrated Operations platform. Key decision points for enabling this technology for both Greenfield projects and existing mines will be discussed. Furthermore, the benefits and improved return on investment that result from deployment of an Integrated Operations strategy will be presented.

Jan 1, 2014

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By Conny Postupack

To make money in mining coal you have to sell it for a lot more than it cost you to get it out of the ground. And yet, every year it cost us more and more to stay inbusiness, while the price we get for coal does not increase at the same rate.

Jan 1, 1990

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By A. Nieto

A vehicle proximity warning–collision avoidance system is being developed using GPS and wireless local area networks to improve safety of off-highway trucks in open pit mines. After two-and a-half years of research, software development, and laboratory testing, field tests were carried out at operating limestone quarries and open pit mining operations to evaluate GPS accuracy and overall system effectiveness under rugged operating conditions. This article describes the progress made on this NIOSH-funded project and discusses the GPS accuracy tests and overall system tests that were carried out during the year 2001 at the Colorado School of Mines Survey Field and at the Morenci open pit copper mine in Arizona. Keywords: GPS, Advanced Mining, Virtual Reality, Wireless Networks, Proximity Warning

Jan 1, 2003

By Y Sha

During the last two decades, China has expanded its iron and steel industry very quickly, from less than 100 Mt/a steel production to over 700 Mt/a. It caused big increases in both domestic iron ore production and imported iron ore quantities year by year. The mode of iron ore supply has changed from almost all domestic supply to major tonnes of imported ore plus domestic ore supply. Over 200 blast furnaces with volumes larger than 1000 m3 each have been built and put into operation. Sinter machines have been enlarged quickly. There are now 135 sinter machines with =200 m2 sintering area each. Pellet production increased from 11.94 Mt in 1999 to 210 Mt in 2011, resulting from rapidly increasing domestic concentrate supply and rapid development of the grate-kiln process. The typical ferrous burden constitution is high basicity sinter plus pellets plus lump. The pellet proportion increased and the sinter proportion decreased gradually. A lot of technical improvements, like deep bed sintering, sintering with a high ratio of limonite, composite sintering, pellet process optimisation, a high ratio of hematite in pelletisation, blast furnace operation with low-grade ferrous burdens and hazardous element control, etc have been made to enhance iron burden quality and to reduce hot metal cost. Chinese iron and steel production is expected to increase slightly in the next few years. Its overcapacity should be controlled effectively. Given the variations of iron ore supply, pellet production will keep progressing in terms of production scale and pellet quality, the sintering process will be improved further by various measures to utilise different ores efficiently, and ferrous burden constitution will be optimised continuously to realise the lowest cost of hot metal production.CITATION:Sha, Y and Wang, Z, 2013. The Chinese iron and steel industry response to the challenges of iron ore supply, in Proceedings Iron Ore 2013 , pp 7-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000

Ten years ago, only 3% of Consol's underground coal production resulted from using the longwall mining method. Today, that figure has grown to 45% and has helped the Pittsburgh-based concern fuel an upswing in productivity. The company reported that productivity at its underground mines, excluding labor strike periods, increased 24% between 1978 and 1981. Last year, an additional 8% increase was achieved. Efforts such as improved safety, training, engineering, and maintenance programs as well as the closing of unproductive mines has contributed to these gains, according to Joseph M. Richards, Consol's executive vice president of operations. But, Richards adds, a great part of the credit goes to longwall mining. What is Longwall Mining? To fully appreciate the advantages of longwall, one needs an understanding of how mining is done by other methods. For instance, in both conventional and continuous mining, rooms or tunnels are dug in the coal seam. Pillars of coal are left standing to support the roof as mining moves forward in the seam. In conventional mining, a slot is cut in the base of the seam and holes for blasting are drilled. After blasting, the coal is loaded. A more efficient method - continuous mining - uses a machine that combines cutting and loading. Longwall mining, by contrast, works backwards from the end of a panel. Two parallel sets of tunnels (development panels) are cut into a seam with continuous mining machines, then connected with a set of crosscuts at the far end. Min¬ing then proceeds back toward the entrance. Longwall mining employs some very productive machines. Large drum shearers, for example, run on a track along the length of the coal face for some 150-180 m (500-600 ft). The shearers cut the coal which falls onto a conveyor system or pan that also runs the entire length of the face. The longwall crew works under a roof of heavy steel supports called shields. As the coal is removed, shearers, pans, and shields are moved forward by hydraulic rams. The roof is allowed to collapse behind the shields. In addition to increasing production, longwall mining is considered to be safer because the miners work under strong steel shields. New designs have made them more rugged and maintenance free, as well as more stable on soft mine floors. Early roof supports, called chocks, had gaps in the roof canopies. The new roof shields now cover the entire working area and are better able to prevent roof material from falling into the working area, thereby improving safety and productivity. Longwall mining also results in a cleaner product in many mines. If the first layer of rock over the coal seam is thin, it might have to be removed with the coal in a room-and-pillar operation so a

Jan 11, 1983

By N M. Caira

The North Arm of Sulawesi hosts numerous gold and base metal occurrences. Compilation and analysis of geological, tectonic, geochemical and isotopic age date data collected over the past six years on the central part of this region have resulted in the definition of 184 prospects and mineral occurrences of various styles occurring in diverse geological settings representing varying tectonic environments and erosional levels. Mineralisation of the following styles have been recognised: porphyry Cu-Au; porphyry-related gold and base metal veins; high-sulphidation Cu-Au-As; low-sulphidation epithermal Au; hydrothermal breccias; and sediment-hosted Au mineralisation. Clusters of occurrences/prospects form mineralised districts representative of magmatic systems with characteristics determined by the tectonic environment prevailing during formation and the subsequent level of exposure by erosion. Distinctly different Miocene and Pliocene porphyry systems are now recognised whilst most of the remaining epithermal mineralisation is thought to be Pliocene or later. The central North Arm of Sulawesi is composed of a Miocene magmatic island arc that is built on an Early Tertiary basement of predominantly oceanic basaltic rocks and overprinted by a Pliocene magmatic arc. A structural fabric dominated by SSE arc-normal and ESE arc-parallel faults was established during the Miocene under a dextral wrench regime and intersections of these major fault sets are favoured sites for Miocene porphyry Cu-Au mineralisation. Strong dextral tension caused by the collision of the Sula Platform, at the close of the Miocene, led to arc-parallel rifting. Sinistral reactivation of the major Miocene structures in the Pliocene led to further rifting, and ENE-dilation. Pliocene intrusions and related mineralisation exploit these dilatant settings. Miocene porphyry Cu-Au mineralisation occurs where late-Miocene quartz diorite stocks have intruded the margins of earlier Miocene plutons of intermediate composition. Porphyry centres have associated peripheral base metal veins, and skarns. Overprinting of porphyry vein sets by epithermal veins is common. Sediment-hosted gold mineralisation occurs in calcareous sediments associated with the Miocene arc. Remnants of the Pliocene volcanic arc, comprised of dacite volcanics, intrusions and voluminous pyroclastics, dominate the south coast and host porphyry Cu-Au, high sulphidation Cu-Au-As deposits, low-sulphidation epithermal Au veins and disseminated gold mineralisation. In some prospects, mineralised sinters are preserved adjacent to vein systems and deeper mineralised stockworks. Diatremes are common and large caldera structures have been identified. Pliocene stocks and porphyry dyke swarms penetrate the main central and northern parts of the Miocene- arc introducing additional porphyry Cu-Au, base metal hydrothermal breccias and low-sulphidation gold veins. Rapid uplift and erosion has resulted in a highly variable preservation of styles of mineralisation adding further diversity within the mineralised districts and telescoping within deposits.

Jan 1, 1999

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By J. E. Johnson

Discussion of the paper of Prof. Henry M. Howe, presented in abstract by Bradley Stoughton at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1181 to 1227. J. E. JOHNSON, JR., Ashland, Wis. :-This material is largely beyond the understanding of most of us practical men, but there are certain portions of that diagram that are of enormous importance. We have been conducting a, very extensive investigation of the quality of charcoal-iron and of all iron, and we have found that this eutectic point here (indicating on chart) is a sort of balance point between the good irons and the bad ones, and I have some slides to show what practical results we have found depending on this point here on the d diagram; and it would be a mistake for men who were -concerned with operation and were getting practical results, to think that these things are of no importance. They are exceedingly hard to understand, and I confess that a great deal of them is beyond me, but there is no doubt that the quality of iron depends to an enormous extent on the location of the carbon content of the iron to the right and left of this point, and the position of that point is dependent upon the silicon, and I wish to make a plea to the practical and operating members of the Institute not to disregard this material on account of its being highly scientific, because I hope to show later that there are matters of the highest practical importance that depend directly upon certain portions of this diagram. HENRY D. HIBBARD, Plainfield, N. J. :-T understand that washed metal, which, is practically pure iron and carbon, does not solidify at one instant, is cast-iron does, but passes through a mushy stage. That has been an enigma as to how and why it did so, and possibly some light might be thrown on it in this connection. BRADLEY STOUGHTON, New York, N. Y.:-If Wittorff's propositions are accepted, washed metal containing more than 4.1 per cent. of carbon would begin to solidify as liquid plus Fe4C

Dec 1, 1912

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006