Search Documents

By L. N. Hill

The classifiers on the primary grinding circuit at Cyprus Sierrita have been upgraded from 0.66 m (26 in) diameter hydrocyclones to 0.84 m (33 in) diameter hydrocyclones. This has resulted in a 4.3 % (11 t/h) (12 standard tons/hour) increase in mill throughput while producing a flotation feed which contains 4.8% less +300 micron (48 mesh Tyler screen size) material. This reduction in flotation feed particle size has increased copper (CU) recovery by 0.8 %. Various grinding circuit relationships were evaluated. These relationships include circulating load versus throughput, horizontal versus vertical cyclone configuration, and the effect of cyclone components on performance. We conclude that the improvements achieved are due to a shift in the overflow size distribution created by a cyclone diameter more suited to our operation, and by eliminating the cyclone capacity constraint in the grinding circuit.

Jan 1, 1994

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By Noel N. Moebs

The U.S. Bureau of Mines is conducting research on many topics relating to the mineral resources of the United States. This is done to ensure an adequate supply of minerals essential to a viable domestic industry and a sound economy. The United States is almost totally dependent on foreign supplies for a number of minerals such as chromium, niobium, tantalum, and manganese for which there is no available substitute, while many other minerals such as titanium are abundantly distributed throughout the earth but seldom occur in adequate concentrations or useful forms. This report describes an example of a small but high-grade occurrence of titanium are in Nelson County, VA. This occurrence could be exploited under favorable economic conditions with new mining technology such as borehole slurry mining. The report demonstrates that the dikes at titanium ore, a mixture of ilmenite and apatite locally termed nelsonite, can be detected and traced along strike using magnetometer traverses. This information will aid in the selection of appropriate slurry borehole mining test sites in the area.

Jan 1, 1993

Modelling Channel Scale Flow in Heap Leaching Using Smooth Particle Hydrodynamics (SPH)

Sep 13, 2010

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Jean-Sébastien Lambert, Joseph Kabuya, Richard Simon

Managing a highwall failure risk in an open pit mine by controlling and mitigating the impact of vibrations produced by blasting operations is key to achieving safe and cost-effective operations. The impetus behind this study was the risk of multiple bench failures in an open pit mine that was detected by Slope Stability Radar (SSR) following blasting at the foot of a highwall. The unstable high wall was over 140 meters(459.3 ft)high and 200 meters(656.2 ft)wide. The quantity of associated material was estimated at 3,000,000 metric tons(3,306,934 US tons). The overall slope angle was 44 degrees. In order to continue mining without causing the highwall to fail, this study was initiated as part of a risk management plan to mitigate this major risk by identifying mitigation measures related to blasting operations and assessing the response of the rock mass to each blast. Identifying blasting mitigation measures consisted of optimizing blasting parameters to avoid failure of the highwall. First, a signature hole operation was carried out to obtain seismic records that were georeferenced and associated with known single charges. The method used made it possible to determine the propagation velocity of the P-waves associated with the various lithologies studied and to calculate, from the geomechanical properties of the rock masses, the maximum peak particle velocities to be respected. Subsequently, the targeted area of operation was modelled with the I-Blast software in order to optimize the firing sequences to be used according to the different lithologies present. The model also made it possible to optimally predict the particle velocities associated with each blast and ensure compliance with the previously determined peak particle velocity limits. The assessment of the rock mass’s response using SSR consisted of defining alarm thresholds and an intervention plan for various possible alarms as well as quantifying the damage to the highwall from blasting. Controlling the impact of blast vibrations on the highwall’s stability was successful, as the mitigation measures used during mining did not accelerate the highwall’s movement. No upward trend in the stabilization time of the rock mass was observed by the SSR after each blast. Post-blast geotechnical inspections and analysis of post-blast deformations in the highwall also did not reveal significant damage to the highwall as a direct consequence of the blasting.

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By Pedro Netto da Silva

O presente trabalho teve como objetivo avaliar a necessidade de substituição das linhas de gás entre a torre de MEA e a entrada no header de distribuição para os vasos Scrubbers em uma plataforma com trinta anos de operação, dado o seu histórico de produção de H2S. Verificou-se a existência de danos possivelmente causados por este contaminante nas tubulações de aço-carbono API GrB e API 5LX 42 pela análise da junta soldada entre flange e tubo, região onde frequentemente ocorrem as falhas na presença de H2S. Observou-se na ZF e nas ZTA a presença de micro-inclusões, as quais foram submetidas à análise química qualitativa por espectrometria dispersiva de raios-X e concluiu-se que eram provenientes do revestimento do eletrodo utilizado no processo de soldagem e da fabricação do aço. Como não foi constatada a presença de trincas ao longo da junta, determinou-se não ser recomendada a substituição de linhas que operam em condições semelhantes.

Aug 8, 2018

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973