Search Documents

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

By Fookes R. A, Bunch K, Gravitis V. L, Watt J. S

The combustible volatile matter in coal mine roadway dusts (CVM) has been determined using x-ray backscatter techniques. The correlation between x-ray and chemical techniques is reasonably good for the 92 samples from collieries on the Bulli seam, and the maximum error expected at the maximum level of 11· 5 weight per cent CVM permitted in the N.S.W. Coal Mines Regulation Act, 1912, as amended, is about ± 2·5 weight per cent. This x-ray technique can be used only when the combustible volatile content of the coal matter (cvm) varies within a limited range, and a separate calibration is required for each coal seam.Portable equipment based on a radioisotope x-ray source ahd digital ratemeter makes possible simple and rapid analysis, and with adaptation to use in coal mines should lead to much more comprehensive testing- ofroadways and hence improved overall prevention of coal dust explosions.

Jan 1, 1977

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By Mark Liskowich

When is it the proper time to initiate engagement with various stakeholders, including Indigenous communities? This paper will demonstrate what stage of a project’s evolution is the appropriate time to initiate a stakeholder engagement plan. It will look at aspects to consider when identifying the communities to involve. It will describe the contents of a Stakeholder Engagement Management Plan as well and touch on how tried and true options analyses, such as a Multiple Accounts Analysis can be used to inform the results of the engagement, guide the development of your project and clearly document the engagement process. It will illustrate the benefits of initiating engagement at the appropriate point in your project’s schedule, and the limitations of doing so too early and at later stages of the project engineering. The benefits of this approach can be realized within any legislative Jurisdiction including the Canadian Environmental Assessment Act 2012 and Canada’s new Impact Assessment Act.

Jan 1, 2020

Overview ?Oil Sands Background ?Water Use in Surface Mining ?Tailings Disposal ?Water Balance for Surface Mining ?Implications of Emerging Regulations ?Water Management Framework ?Tailings Performance Criteria (Directive 074)

May 1, 2009

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By H. Kellerwessel

This paper refers to the new crushing and grinding process, which was invented by Professor Schönert (Ref.1), Clausthal, Germy (author of one of the papers presented at this meeting). The process is known as high pressure particle bed comminution or interparticle crushing. Several papers by Professor Schonert and his coworkers and by specialists of the companies producing the necessary equipment under license agreements already described fundamentals of the process, the equipment used, results of lab size and large scale tests and finally the first results of truly commercial operations (Ref .2 to 11). Therefore it should be sufficient to summarize the main facts here: - To a bed of bulk material a pressure of more than 50 MPa is applied. Comminution is achieved mainly by the pressure which one particle transfers to the other and not by squeezing single particles between the working surfaces of some crusher or grinding media.

Jan 1, 1987

By Lyall Zickrick

Numerous brands of virgin pig lead are used in the manufacture of lead and lead-alloy cable sheath for commercial cables. In changing from one brand of pig lead to another a readjustment of press operating conditions is nearly always necessary. This is due largely to different flow characteristics, and some brands extrude at a much lower pressure than others; for example, copper-bearing lead requires much more pressure than a low-bismuth lead under the same operating conditions. With the modern type of lead press the extrusion practice in general differs very little. Molten lead at a temperature of 375" to 400" C. (710" to 750" F.) is cast in a water-cooled cylinder and allowed to cool or solidify into a slug for six to nine minutes, This slug is forced into the die block and around the core tube through which the cable runs. The • die block is held at an optimum temperature by means of gas flames, usually 175" to 225" C. (350" to 435" F.). Measurements of the temperature of the cable sheath taken at the time of extrusion have covered a range of 190" to 225" C. (375" to 435" F.). According to Tammann, the rate of extrusion for a metal under constant pressure through a simple orifice is almost doubled for each 10" C. rise in temperature. Because of the irregularity of die-block construction, such a great increase is not obtained in lead-cable extrusion practice. To obtain more definite information about the effect of small percentages of metals usually present as impurities in virgin pig lead, a series of compression tests were made covering several different brands of lead and various alloys. Since the usual temperature of the sheath is approximately 200" C. as it emerges from the die block, these compression tests were all performed at 200" C. Five different brands of virgin pig lead were selected, as follows: Brand A: A desilverized western lead of very high purity. This lead contains neit,her copper nor bismuth. Brand B: A bismuth-free southeastern Missouri lead, usually containing 0.05 to 0.08 per cent copper. Brand C: A copper-free mid-western desilverized lead of very good grade, usually containing around 0.06 to 0.10 per cent bismuth.

Jan 1, 1932

By Lyall Zickrick

NUMEROUS brands of virgin pig lead are used in the manufacture of lead and lead-alloy cable sheath for commercial cables. In changing from one brand of pig lead to another a readjustment of press operating conditions is nearly always necessary. This is due largely to different flow characteristics, and some brands extrude at a much lower pressure than others; for example, copper-bearing lead requires much more pressure than a low-bismuth lead under the same operating conditions. With the modern type of lead press the extrusion practice in general differs very little. Molten lead at a temperature of 375° to 400° C. (710° to 750° F.) is cast in a water-cooled cylinder and allowed to cool or solidify into a slug for six to nine minutes. . This slug is forced into the die block and around the core tube through which the cable runs. The die block is held at an optimum temperature by means of gas flames, usually 175° to 225° C. (350° to 4.35° F.). Measurements of the tem¬perature of the cable sheath taken at the time of extrusion have covered a range of 190° to 225° C. (375° to 435° F.). According to Tammann, the rate of extrusion for a metal under constant pressure through a simple orifice is almost doubled for each 10° C. rise in temperature. Because of the irregularity of die-block construction, such a great increase is not obtained in lead-cable extrusion practice. To obtain more" definite information about the effect of small per¬centages of metals usually present as impurities in virgin pig lead, a series of compression tests were made covering several different brands of lead and various alloys. Since the usual temperature of the sheath is approxi¬mately 200.° C. as it emerges from the die block, these compression tests were all performed at 200° C. Five different brands of virgin pig lead were selected, as follows: Brand A: A desilverized western lead of very high purity. This lead contains neither copper nor bismuth. Brand B: A bismuth-free southeastern Missouri lead, usually con¬taining 0.05 to 0.08 per cent copper. Brand C: A copper-free mid-western desilverized lead of very good grade, usually containing around 0.06 to 0.10 per cent bismuth.

Jan 1, 1932

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By B. K. Shibler, K. C. Vincent, W. W. Agey

"INTRODUCTION As a part of the investigation of domestic manganese deposits, examining engineers of the Bureau of Mines collected samples of ore from three from three properties in the general vicinity of Tracy, Calif.The Buckeye mine is 23 miles of Tracy, just inside the northeast boundary of Stanislaus County. The mine is owned by K.O. Winship estate of San Francisco and is leased by Verner Allen, also of San Francisco.The ore is principally manganese carbonate occurring in interbedded layers in white chert, with the original,carbonate mineral altered in place. Four samples, representing four types of ore, were submitted, as follows: A, black oxide; B, pink carbonate; C, gray carbonate.The Wilfred Murphy property (also known as the Murmac claims) is approximately 30 airline miles south of Tracy. The property can be reached by road from either Livermore or Patterson and is on the divide separating Santa Clara and Stanislaua Counties Calif. The ore occurs in lenses along a white-chert formation. A 2-ton sample of ore for testing was taken from a dump accumulated from assessment and development work. The Ladd mine, 13 miles from Tracy in San Joaquin County is owned by Pat J. Connolly of Tracy and is leased by Mack C. Lake of San Francisco. The ore is essentially a chert impregnated with manganese oxides and the association is therefore exceedingly intimate and complex. Samples from each of the three adit levels of the mine were submitted for ore-dressing study.As the samples differed widely in physical character and response to ore-dressing methods of treatment, beneficiation of ores from each property was considered as a separate problem. Hence results of the investigations will be prescribed in separate sections of this report."

Nov 1, 1947

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid-bake leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400 ºC) sulfuric acid baking of an enargite concentrate followed by water-leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase for baking at 400 ºC. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400 ºC, sulfuric acid amount of 0.5 mL/g of concentrate, and 2 h baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). XRD analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in similar fashion.

Jan 1, 2012

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002