Search Documents

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By J. Dean Warner

From 1984 through 1987, the Bureau of Mines investigated numerous prospects and new discoveries of columbium, rare-earth elements (REE), uranium, zirconium, and other metals associated with the multi-phased peralkaline granite at Bokan Mountain, southeastern Alaska. This report summarizes the mineral evaluations and estimates indicated and inferred resources for those prospects containing significant tonnage and grade. A total of approximately 96.2 MM lb Cb205 (43 pct of the tonnage at a grade exceeding 0.125 pct Cb205), and 11.8 MM lb U308, 27.9 MM lb Th02, 133.0 MM lb Y203, 637.6 MM lb ZrO2, and 241 MM lb REO are estimated to be contained within nine deposits totalling 37.8 million tons (at least 80 pct of resource tonnage also exceeds 0.5 pct Y203 + REO). Generally, half of the REO content is composed of the heavy yttrium subgroup. Several deposits also contain beryllium and tantalum; 2.1 MM lb of Ta205 and 8.9 MM lbs of BeO were estimated. These estimates would likely be substantially increased with additional exploration. Four deposit types were investigated; shear zones and fracture-related deposits, pegmatites, mineralized dikes, and placers. Mineralized dikes contain most of the beryllium, columbium, tantalum, yttrium, zirconium, and REE resources, whereas shear zones and fracture-related deposits (Ross-Adams mine) contain the principal of the uranium resource. Pegmatites are similarly mineralized as are dike deposits, and contain low levels of gold. Placer potential is suggested, but no deposits were found.

Jan 1, 2011

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

In undertaking to write a few notes on practical mining in Bendigo, the great quartz mining centre of Victoria, which just now is celebrating its fiftieth anniversary of gold mining, satisfaction must be expressed which is, no doubt, shared by all mining men and inyestors, that Bendigo has not lagged behind other Australian mining districts in the evolution of mining from its crude state, subsequent to the discovery of gold in 185 to its present more perfect state; and though it may be said that it has not yet reached the high pinnacle of perfection towards which advanced science and change of conditions may yet lead it in the course of future progress, yet, what has already been done in this respect, the adoption of the most approved methods appliances and modern machinery, tending towards greater and still greater efficiency, facility, and economy in our mining industry, must be accepted as a guarantee that in tne future as well as in the past, progress in our means of developing our mining resources will ever remain our watchword, by means of which future difficulties will be overcome as well as they have been removed in the past.The adoption of this principal, combined with a study of rigid economy, has raised gold mining here, as well as in other places, from a state of speculation, and sometimes wild speculation, to the status of a solid, stable industry, the strong supportand backbone of the country in which it flourishes. Two of the principal factors which have been to a great extent instrumental in bringing about this satisfactory state, must be specially mentioned.

Jan 1, 1902

By Fredy Llerena B.

El presente trabajo describe la geología del depósito minero Candelaria, perteneciente al distrito minero de Castrovirrey, Huancavelica. Dicho depósito está asociado a la actividad ígnea de centros y domos volcánicos del terciario medio o superior, mientras que la veta Candelaria está constituida por tetrahodrita, enargita, boulangerita, bournouita, jamesonita, esfalerita, galena, bismutinito, chalcopirita y como minerales de ganga, pirita, cuarzo, barita, oropimente, regelgar, marcasita, arsenopirita, así como hay lazos cimoidea. De otro lado, las intersecciones de vetas favorecen la mineralización y el Domo Volcánico Candelaria es favorable a la mineralización al igual que los tufos.

Oct 14, 1980

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By Pier Francesco Paglini, Gian Luca Menchini, Pier Francesco Boschi

"PROJECTThe “Caltanissetta” Tunnel is part of the ANAS S.p.A (National Autonomous Roads Corporation) $ 1.3 Billion Highway 640 Caltanissetta-Agrigento (Sicily, Italy) Rehabilitation Project, consisting in upgrading of 62 km (40 miles) of highway. The Italian multinational construction company Cooperativa Muratori & Cementisti di Ravenna, is the General Contractor for the design and build contract. The highway S.S. 640 starts from Porto Empedocle, to the intersection with the Motorway A 19 Catania-Palermo.The entire project, double carriageway designed for speed 70-120 km/h and maximum longitudinal slope of 4.2%, is divided into two sections. First Section: just finished and opened to traffic. Second Section: mainly involving the province of Caltanissetta, length about 28 km (18 miles), works started in 2013. This second section includes the most challenging work of all the project, the “Caltanissetta” tunnel consisting of two separate tubes, each with 3.9 km length and inside diameter of 13.50 m, in order to host 2 traffic lines and an emergency line. HORIZONTAL AND VERTICAL ALIGNMENT - GEOLOGY AND HYDROGEOLOGYThe plan alignment of “Caltanissetta” tunnel is formed by two tubes which are located at a minimum mutual distance of 22 m to a maximum of 63 m, with n. 9 pedestrian and n. 4 road cross passages; ventilation shafts are not provided. Overburden over portals area is about 5 m till a maximum of 120 m. Tunnel sections have variable longitudinal slope from 2.6% to 0.5%, transversal slope of about 3.5%. Right tube length is 3,992 m, left tube length is 3,877 m."

Jan 1, 2016

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962

FEBRUARY 26TH. MORNING SESSION: The sixteenth regular meeting of the Rocky Mountain Coal Mining Institute was called to order in one of the private dining rooms of the Albany Hotel, Monday morning, at 11 o'clock, with the President, F. W. Whiteside, in the chair, one hundred and one members being registered. The minutes of the previous meeting were read and approved. The Treasurer reported the finances of the Institute in excellent shape. The President appointed J. B. Marks, J. S. Veach and W. A. Ream as a Resolution Committee, and Frank A. Young, M. B. Urquhart and G. A. Murphy a Nominating Committee. There being no further business the meeting adjourned. AFTERNOON SESSION: The afternoon session was called to order in the Ball Room of the Albany Hotel, with approximately one hundred members present, President Whiteside presiding. A. L. Jones read his paper entitled, "The Power Problem of the Coal Mine," and C. E. Drennan, his paper, "Why Alternating Current." These papers were thoroughly discussed, after which the meeting adjourned. EVENING SESSION: At 6:45 p. m. two hundred and fifty-three members and invited guests met in the Ball Room of the Albany Hotel for the banquet. Harry F. Nash was toastmaster, and George Sanford Holmes the principal speaker. Following Mr. Holmes speech, H. N. Wheeler delivered his humorous oration of the "Annexation of Cuba;" following this certain members of the Institute gave an entertainment depicting a fictitious meeting of the United States Coal Commission. Chester Mott, formerly a member of the Institute wrote the words and songs of the entertainment, and directed it. After the show the assembly enjoyed a dance.

Jan 1, 1923

By Karl J. C. Harries

"10.1. INTRODUCTIONDefinitions are a necessary part of every agreement. Their purposes are to assist the reader in reading and understanding an agreement and to attempt to avert potential confusion and, therefore, disputes. In some circumstances, they may be critical in deciding a dispute. As they are often substantive, they should not be treated lightly.It is far easier and less confusing for a reader to read “the Company” or “the Recipient” than to be faced with “the party of the First Part”, or to see the “Jones Property” than “that part of the property hereinbefore described in paragraph 1.01 hereof”. It is also advisable not to use “-ee” and “- or”, as in payee and payor.One thing must always be remembered: once a word has been defined in an agreement, it will always have the defined meaning unless the contrary is clearly indicated or is required to make sense of a provision.2 It can be confusing for a reader if commonly used words are defined in other than ordinary terms. Unique words that will stand out in the text are more likely to be recognized as having special meaning. It is also good practice to identify defined terms by capitalizing them in the text of the agreement. Boldfacing of definitions is also sometimes used for this purpose but, as boldfacing is not easily identified in handwritten revisions, it can be missed in the press of negotiations, especially when several typists are involved. Lack of consistency in identifying defined terms is not a fatal mistake, but it can create confusion, especially if the reader is new to the agreement or is reading it in a highly technical manner, such as when there is a dispute.If definitions used in the main text also apply to a schedule, they need not be included in both. Omitting them from the schedule makes the agreement look shorter, which to some people is a benefit. If definitions are not repeated, make certain that the schedule clearly indicates that words defined in the main text have the same defined meanings in the schedule3 and are clearly identified as defined words. In considering whether or not to repeat in a royalty schedule definitions appearing in the agreement proper, think of definitions as an aid and a reminder to the reader. Repeating them will help a reader, if only by saving the nuisance of remembering where to find them in the main text and constantly turning to it. All the definitions needed to read the schedule will be right there, so that the schedule is a self-contained document. Just make certain that, if you do repeat a definition, you repeat it in identical terms. If you have to change any defined term to make it fit the royalty provisions, use a different word or phrase as the defined term to warn the reader that he is dealing with a different concept.4"

Jan 1, 2003

By V 9. 0 / 300 dpi

ATHOUGH turquoise mining was, so far as we know, the first large, well-organized mining operation,' gem mining, from the Roman con-quest of Egypt until the opening of the South African pipe diamond mines some 50 years ago, was largely carried on' by individuals 01' small companies in a relatively primitive way. Now" however" gem mining does not yield in efficiency or in scale of operations to the mining of other mineral products. In 1926 the diamond mines of the world milled some 9,000,000 cu. yd. and produced 0,43 cu. yd. diamonds, a remarkable example of concentration. The Premier Diamond Mining Co. up to Oct. 31, 1927, had milled 116,455,550 loads (each of 16 cu. ft.) from which 26,-217,144 carats of diamonds" worth £29,897,971 2s, 9d., were recovered. The Burma Ruby Mines, Ltd., operating sever-al alluvial mines in Burma in 1911-12, mined and milled 1,479,845 truckloads of gemmiferous earth for 15c. per load. We of the industry can there-fore, with good grace, disclose some of the myths and also describe some of the primitive mining methods of the, dark ages of our industry. The methods, so far as I know, were not patented, and if they were, the patents have expired, so that engineers in other branches of the art are free to use them if they see fit.

Jan 1, 1928

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

This evening I intend to explain the position of the gold mining industry in the light of post war trends and events.I propose initially to comment on gold production throughout the World and then proceed to the state of the industry in Australia, with an account of the efforts made within the industry to maintain levels of production. This will be followed hy a statement on assistance granted to the industry by Federal and State Governments.Annual World gold production is estimated at 51,000,060 fine ounces, made up as followsSouth Africa - 27,300,000 fine ouncesCanada 4,200,000 " "U.S.A. 1,500,000 " "Australia - 1,000,000 " " Others 5,000,000 " "----- 39,000,000 " "Estimated Russianproduction - 12,000,000 " "Total 51,000,000 " "The opening up of new highly payable mines during the post war years has contributed to the preponderence of production in South Africa.In 1962 some 24 new mines produced 73 per cent of South Africa's gold, and contributed almost 90 per cent to the industrial profits.At the same time, 20 old mines were struggling to main...

Jan 1, 1964

By Michael Hughes, Paul Bonapace, Harry Charalambu, Stephen Rigbey

Ontario Power Generation is building a 10.4-km water diversion tunnel in Niagara Falls, Canada. The tunnel is a two-pass, cast-in-place prestressed concrete-lined pres-sure tunnel with a nominal internal diameter of 12.7 m. It is mostly situated within the Queenston formation which swells in contact with fresh water and has very aggressive groundwater. Tunneling in this material presents challenges in both design and construction. The tunnel design includes for a membrane to eliminate the potential for rock swelling and to protect the concrete liner from the ground conditions. A unique three-stage Geotechnical Baseline Report (GBR) is being used and is expected to provide an equitable method of dealing with any variations in subsurface conditions.

Jan 1, 2007