Search Documents

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By Lee Ann Gardner

This U.S. Bureau of Mines publication presents a case study of the processes used in permitting the Nome Offshore Placer Project, a gold mining project offshore Nome, Alaska which operated from 1985 through 1990. The mining project, developed by Western Gold Exploration and Mining Company, Limited Partnership (WestGold), used the BIMA, which was at the time the largest bucketline mining vessel in the world, to dredge gold from the ocean floor. This case study reviews the permitting process from the regulators' and industry's perspectives, as well as characterizing the efficiencies and inefficiencies associated with this case. The Federal, State and local laws applicable to the Nome Offshore Placer Project are identified, agency jurisdiction and interagency relationships are explored, and the chronology of the permitting process is examined. The regulatory authorities for both environmental monitoring and post-mining monitoring are delineated. Significant milestones affecting the project and required regulatory submittals are also included. The case study of the Nome Offshore Placer Project is detailed with respect to agency involvement and coordination, approaches to permitting from both the regulators' and developer's perspective, environmental issues, and permit stipulations which were unique to the project. The advantages and disadvantages of these topics are discussed.

Jan 1, 1992

By R. S. Dean

In an earlier paper Dean and Hersberger5/ gave preliminary results a d discussed briefly the use in flotation of organic reagents of the type known in the textile industry as "wetting agents.? These reagents are those with a molecular structure comprising a long hydrocarbon chain attached to a. highly molar or hydrorhile group in such manner that ionization is nearly complete in dilute solution and the resultant ionic grouping has a very considerable hydrophile-lipophile unbalance in the structure. As a result of this characteristic structure these reagents are more or less powerful frothers and emulsifiers. Ten the degree of hydrophile-lipaphile unbalance is sufficiently great and specific chemical factors are absent these compounds behave in flotation as noncollecting frothers insensitive to reason¬able changes of pH.

Jan 1, 1937

By R. S. Dean

In an earlier paper Dean and Hersberger5/ gave preliminary results a d discussed briefly the use in flotation of organic reagents of the type known in the textile industry as "wetting agents.? These reagents are those with a molecular structure comprising a long hydrocarbon chain attached to a. highly molar or hydrophile group in such manner that ionization is nearly complete in dilute solution and the resultant ionic grouping has a very considerable hydrophile-lipophile unbalance in the structure. As a result of this characteristic structure these reagents are more or less powerful frothers and emulsifiers. Ten the degree of bydrophile-lipaphile unbalance is sufficiently great and specific chemical factors are absent these compounds behave in flotation as noncollecting frothers insensitive to reasonable changes of pH.

Jan 1, 1937

New Zealand has often been quoted by metallurgists and others as one of the countries in which Tellurium is found, and locally it has been recorded that appreciable quantities of tellurium have been met with in the Thames and surroundingdistricts. However, specimens containing tellurium which have been obtained on this field have not been preserved and their scarcity today points to the fact that tellurium is not here abundant.To ascertain its distribution, analyses and assays have been made by the author on a large number of ores, the results of several of which are given below.The presence of any considerable percentage of tellurium has an important bearing on the metallurgical treatment of ores in which it is found.

Jan 1, 1901

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

Investigation on Multicomponent Semi-Autogenous Grinding

Sep 13, 2010

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

Advances in Coarse Particle Recovery - Fluidised-Bed Flotation

Sep 13, 2010