Search Documents

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By Henrique Dias Gatti Turrer

Atividades de pesquisa e desenvolvimento (P&D) possuem efeito positivo nos indicadores econômico-financeiros das organizações. Essas atividades possuem características de projetos, e, por isso, podem ser submetidas aos processos de gerenciamento recomendados pelo PMBOK. As atividades da gerência de P&D do Minas-Rio da Anglo American foram submetidas à alguns desses processos. Inicialmente, foram estratificados os processos por magnitude de esforço e de impacto. Oito processos foram classificados como de baixo esforço e alto impacto e, por isso, totalmente implementados. A criação e aplicação de três ativos organizacionais padronizados para todas as atividades realizadas permitiu o desenvolvimento de grande parte dos processos considerados mais importantes. Um questionário de avaliação do grau de maturidade em gerenciamento de projetos foi respondido por parte da equipe antes e depois da adoção formal de tais processos. O grau de maturidade aumentou significativamente, 150%, em dois anos, passando do nível conceitual para padronizado. Além disso, foi observada um aumento significativo, igual a 731%, no número de atividades realizadas pela área.

Oct 30, 2017

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

Influence of Grinding Media on the Flotation of Carbonate Using Sodium Oleate as Collector

Sep 13, 2010

By Douglas W. Christie

Deep foundations in Washington, DC have played a role in the city?s development since the 19th century. Designers of government and commercial buildings sought deep foundations initially to minimize settlement of structures. As the western portion of the National Mall was made by filling in portions of the Potomac River, numerous memorials and monuments on the Mall required deep foundations. In recent years deep foundations have been used to allow underground construction for various reasons. Commercial developers have sought to maximize the use of sites by developing below-grade space for parking to meet code requirements and offset the limits on building heights. Underground museum and gallery space has been constructed to expand public space while preserving open space above grade. Access and security concerns have prompted the design of underground visitor centers rather than above-grade structures.

Jan 1, 2006

By W. Newcomen, D. Brox

The assessment of the stability performance of open pit highwalls has traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work has been reviewed and are endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on relatively consistent trends in highwall strain data. L’évaluation du niveau de stabilité des hauts murs de carrières a traditionnellement été basée sur les taux de mouvements de surfaces. Bien que cette approche soit généralement acceptée à travers l’industrie, elle présente des défis pour la définition de seuils appropriés concernant la sécurité des opérations minières et n’adresse pas la notion de déformations totales. Des données de mouvements de surface provenant d’un nombre limité d’opérations minières à ciel ouvert d’Amérique du Nord et du Sud ont été évaluées en terme de déformation des hauts murs, de qualité de la masse rocheuse et des mécanismes inférés d’instabilité. Des seuils de déformation pour différentes phases clefs de stabilité de hauts murs ont été revus et sont endossés, basé sur l'évaluation de donnés additionnelles. Un critère de déformation empirique pour l’évaluation de la stabilité des hauts murs est postulé, basé sur des tendances relativement consistantes de données de déformations de hauts murs. Die Beurteilung der Stabilität von hohen Felsböschungen basiert traditionellerweise von Oberflächenbewegungen. Obwohl dieses Verfahren im Allgemeinen akzeptiert wird, stellt es jedoch gewisse Probleme für die Festlegung von Grenzwerten für die Sicherheit dar. Die totalen Dehnungen werden bei dieser Betrachtungsweise vernachlässigt. Eine beschränkte Anzahl von Oberflächenbewegungs Daten von Bergbauwerke in Nord- und Südamerika sind in Bezug auf die Dehnungen von hohen Felsböschungen, Felsqualität und davon abgeleiteten Bruchmechanismen untersucht worden. Grenzwerte für die Belastung von hohen Felsböschungen während den massgebenden Bauetappen aus bisherigen Projekten sind begutachtet und durch zusätzliche Untersuchungen bestätigt worden. Gestützt auf relativ konsitenten Trends, ist hier ein empirisches Verfahren der Dehnungen in hohen Felsböschungen zur Beurteilung der Stabilität vorgestellt.

Jan 1, 2003

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By Crook KAW

New sedimentological and biostratigraphic data indicate that the Leron Formation in the Markham Suture Zone, Papua New Guinea (PNG) represented Pleist- ocene alluvial fan-delta deposition in shallow marine to lacustrine environments. The distribution of sedimentary regimes in the Leron Formation indicates that during collision zone evolution, various tectono-sedimentary regimes do not always track the movement of the triple-junction systematically as idealized by Crook's (1989a) model. The migration of various tectono-sedimentary regimes are also controlled and influenced by the effects of second-order geometric features of the convergent margins. Leron Formation in the Markham Valley represents late to post-collisional marine to fluvial molasse. Foraminifera indicate that the collision and concomitant suturing of the Markham valley occurred after 1.32Ma.

Jan 1, 1991

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

Coal cleat and faulting influence failure, gas release, and choice of preferred mining directions, locations, and sequences. Unfortunately soil and younger rock cover restrict direct mapping of these structures ahead of mining operations. Aerial photographs of cover contain indirect indications of concealed structures in arrays of linear photostructures. These arrays are commonly too complex for interpretation by simple visual inspection.Analytical techniques applicable to complex arrays are illustrated for a covered part of the Galilee Coal Basin, Queensland. These techniques are: optical determination of sets in arrays of photostructures; correlation of these sets with sub-surface structures; filtering of m-rays for particular sets; detection of anomalies associated with concealed structures in the density distributions of particular sets; fitting filtered arrays to trajectories; correlation of trajectories with the regional directional variations of concealed structures; contouring of ratios of sets to discriminate anomalies associated with concealed fractures and variations in the total and bed thicknesses of cover; kinematic and dynamic inference on the basis of fracture-trace angular and spatial relationships.

Jan 1, 1979

By M. A. El-Sohby

The paper describes some problems encountered with the foundation of a deep drainage caisson constructed on the Nile Bank in Cairo. The use of suction dredging while sinking the caisson led to a piping failure of the sandy soil in the base which was loosened during the process of pumping. A study was carried out to investigate the problem and a procedure was adopted to retain the stability of the caisson.

Jan 1, 2010

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982

By Peter J. Clarke

The petroleum industry continued to be the most important mineral activity in Bahrain during 1978-79. Revenues generated by the petroleum sector increased from $378 million' in 1977 to an estimated $419 million in 1978 and approximately $522.5 million in 1979, despite decreasing production over the 2 year period. There were two oilfields that produced revenues for Bahrain, the Awali oilfield, the nation's only onshore producer, and the Abu Sa'fah oilfield, located in the Persian Gulf, north of Bahrain, The Await oilfield has been decreasing output from a high of 27,973,000 barrels in 1970 to 19,000,000 barrels in 1979. Bahrain shared the revenues from the Abu Sa'fah oilfield with Saudi Arabia, as settlement of an ownership dispute. For the first time, in 1978, revenues from the Abu Sa'fah oilfield represented over 50% of the total receipts from the petroleum sector. The years 1978-79 saw the gradual takeover of the Bahrain Petroleum Co. (Bapco), formerly a subsidiary of the California Texas Petroleum Co. (Caltex), by the Government-owned Bahrain National Oil Co. (Banoco). By yearend 1978, Banoco owned 60% of Bapco, and Caltex the remaining 40%. The Government-owned company controlled exploration concessions, managed domestic marketing of petroleum products, and controlled natural gas production and marketing. On December 15, 1979, the Bahrain Government completed full takeover of the Bapco operations. Bapco will continue to own and operate the 250,000-barrel-per-day oil refinery located near Sitrah, as well as handle foreign marketing of petroleum products.

Jan 1, 1981

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By Grafton Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by rite in Metallurgical and Chemical Engineering for January, 1915. CAST-IRON TEST PLUG, SHOWING LOW MOTTLED AND MOTTLED FRACTURES. Several years ago, while I was thief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in befit open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the sill on ill every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 10, 1915