Search Documents

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

By Oliver Bowles

Under a cooperative agreement between the Bureau of Mines, the United States Geological Survey, and the United States Bureau of Standards, a study of the stone-quarrying industries of the country was begun in 1914. The results of investigations made have been published from time to time.1 During the World War the Bureau of Mines centered its attention on problems relating to national defense, and detailed studies of stone-quarry problems were not undertaken except for an investigation of labor saving at limestone quarries, reported in Technical Paper 203, which related to a question of military importance. Since the return of peace, the high cost of materials and labor has made more imperative than in prewar times the conduct of investigations for aiding the quarrying industries in every way possible to adopt more economical methods and to utilize the most efficient labor-saving equipment. The publications already issued have had a wide demand, and in the interest of the quarry industries the bureau proposes to issue additions to the series as rapidly as funds are available. In an endeavor to promote economy and the reduction of waste in the slate industry, a study of slate quarrying was begun in 1920 and covered a period of about two years. Sixty-five active quarries were visited, and a detailed study made of all problems bearing on their successful operation. Field study was supplemented by a study of all information available in books or published articles on slate quarrying.

Jan 1, 1922

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

The Ministry of Commerce has been carrying out an evaluation of the resources of the Northwest Nelson region. In part this was to revisit the issues covered in the earlier proposal to close part of Northwest Nelson to mining under section 24 of the Mining Act (1971) initiated in 1990. In addition, the option of using GIS to integrate a variety of spatial data sets to aid policy formulation could be tested. The Northwest Nelson assessment would be a useful trial. The subsequent national park proposal provided a major impetus to the project and resulted in the scope of the study being broadened to include all energy and minerals resources.

Jan 1, 1993

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By Valois R. Shea-Albin

Increasing pressure from State and Federal agencies to mitigate mining-induced subsidence damage to overlying structures has presented a unique problem to the coal industry in the western United States. Because sandstone escarpments are an environmental issue, millions of tons of coal reserves that underlie these escarpments risk being classified as unminable by regulatory agencies. At this time, the effect of subsidence on escarpments has not been well documented or characterized. The Bureau of Mines is using numerical modeling techniques to analyze escarpment response to longwall mining. Two- and three-dimensional finite element models have been constructed for a study area near Price, Utah, where longwall panels were mined near an escarpment. This status report includes preliminary results showing that the pattern of subsidence surrounding the escarpment can be simulated through numerical modeling. Models that include such structural details as joint and fracture patterns will better simulate subsidence patterns .and magnitude. By locating longwall panels strategically in relation to the escarpment, stability may be preserved throughout the mining process. Numerical modeling provides a method to analyze relatively quickly the effects of longwall panel location and resulting subsidence on escarpment stability. The goal is to provide a relatively accurate predictive tool for mine planning to determine if escarpment stability can be maintained while maximizing extraction of the coal reserves.

Jan 1, 1986

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990&apos;s new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 &#181;m voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A study of drilling data at various stages of development of an orebody show that the semi-variogram, used for calculating the accuracy of block estimates can be ill-defined if too few data are available. The consequencesin this case are to have blocks supposedly more accurately known than is possible at the early drilling stage; such a result being potentially dangerous. However, as the amount of data increases the recalculated, semi-variograms approach the underlying semi-variogram of the deposit and the calculations made using them become more reliable and robust.

Jan 1, 1977

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines&apos; MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By Jean M. Richardson, Steven R. Williams

"Geometallurgical mapping is a new team-based approach that documents variability within an orebody and quantifies the impact of geology (host rocks, alteration and structure) and mineralogy on grinding, metallurgical response and metal recovery processes. The quantitative, spatially constrained database that results can be readily integrated into 3-D block models and mine planning activities. Thus it is an important tool to reduce the technical risk associated with new mine developments or expansions.Normally undertaken during pre-feasibility or feasibility planning stages, the first step of geometallurgical mapping is to review the geology, mineralogy and other critical parameters and construct a geometallurgical matrix. This matrix provides an objective base to then guide sampling and/or compositing activity for physical property and metallurgical testing. Depending on the project, an array of testing techniques can be used to characterize the ore and feed data into the geometallurgical model.While the range and number of tests needed is project-dependant, the geometallurgical mapping approach allows the development of empirical models or interdependent relationships, grounded by spatially-constrained real data. Extensive data sets collected using less expensive testing methods can be meaningfully correlated with results from complex specialty tests to yield realistic metallurgical recovery data.With geometallurgical mapping completed, the resulting database can be integrated into an overall 3-D block mine model. This means that metallurgical response can be used to realistically forecast the recoveries of specific blocks, perhaps sampled only by drilling. Mine planning can then incorporate the forecasted metallurgical response and generate future project cash-flows; opening the door to economic optimization of the mine exploitation."

Jan 1, 2004

The authors describe two stratiform intrusions within a two miles thick ophiolite belt, one of the many ophiolite (serpentine) belts of the eugeosynclinal sequences of the Kalgoorlie System (metamorphic age c.2700 million years). Unusually good evidence of gravitational differentiation involving cumulates for an Alpine type peridotite-gabbro intrusion has been obtained, in spite of modifications of the original igneous rocks imposed by regional metamorphism. Unmetamorphosed relics of cumulate rocks are a surprising feature of this occurIfence.&apos;fhe differentiation process reflected in the layered sequences is compared to that of the Stillwater Intrusion, Montana. Phase, cryptic and rhythmic layering are recognized. The economic significance of this study lies not only in the possibility of nickel mineralization in this ophiolite belt, but also in that much detailed information on the nature of these belts, which is difficult to obtain in the case of the more altered and sheared rocks of the belts carrying gold and nickel ore deposits nearby, is gathered from the Yilmia occurrences.

Jan 1, 1969

Detailed mineralogical investigation of a tailing sample from the Juno plant circuit at Tennant Creek was carried out to determine the nature of the unrecovered bismuth and whether any possibility existed for improving bismuth recovery. The investigation showed that the Ibismuth was present in a complex mixture of Bi-Pb-Ou-Se-S minerals (termed &quot;bismuthinite&quot;), of which about 74 per cent was locked (mainly with magnetite) and 26 per cent was liberated (18 per cent in the minus 7 &#181;m slime). The results suggested that attention should be directed to both finer grinding and improved flotation of slime &quot;bismuthinite&quot;, and testwork carried out by Peko Mines N.L. on the basis of these recommendations led to a significant improvement in bismuth recovery.Detailed mineralogical investigation of two Juno concentrates was carried out to determine the nature of the selenium present and whether any possibility existed for improving the selenium grade. The investigation indicated that virtqally all the bismuth, selenium, and lead was present in &quot;bismuthinite&quot;, which showed a composition range of 32-82 per cent Bi, 0-42 per cent Pb, 0-24 per cent Se, and 5-18 per cent S. Differences in the Bi/Se ratios of the two concentrates could be attributed to different average Bi/Se ratios of the constituent &quot;bismuthinite&quot;, and the relatively low selenium grade of the &quot;bismuthinite&quot; precluded the possibility of obtaining a high grade selenium concentrate with high selenium recovery.However, differential flotation and/or low intensity magnetic separation to remove chakopyrite, and magnetite, the main diluents of the concentrate, could be expected to upgrade the selenium content byup to 80 per cent (relative) and .festwork carried out by Peko Mines N.L. on the basis of the recommendations of the mineralogical investigation confirmed that depression of chalcopyrite in the flotation circuit could produce significantly improved selenium grades.These investigations illustrate the application of mineralogy to the practical problems of improving plant performance. Mineralogy has an important role to play in providing quantitative data on which the metallurgist can evaluate plant performance and base a programme of metallurgical testwork, and early mineralogical investigation of feeds, concentrates, middlings, and tailings can lead to the avoidance of much abortive and expensive metallurgical testwork.

Jan 1, 1974

By E. Fahrenkrog, D. Sbartaro, E. N. Cifuentes

An intelligent supervisor using expert system tools and applied to a crushing plant has been developed with a structure based on a model of a human operator. It consists of a knowledge base containing a qualitative model of the process and a rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of system to supervise the automatic operation of a plant. There has been very significant development in artificial intelligence over the last two decades. Within this development, two approaches can be distinguished, (Winston, 1984). The "model approach," in which the main objective is to understand and model the be¬havior of living systems. The second approach is the "engineering approach." Here, systems capable of performing tasks usually requiring human intelligence are created. As part of this latter approach, knowledge engineering and its main achievement, expert systems, have been developed. Expert systems arose from the need to incorporate the abilities of a human expert in solving realistic problems in which the conventional approach has great difficulties. The first successful applications of expert systems were in medical diagnosis, geophysics, and fault detection. However, since 1971, when Fu (1971; defined intelligent control as the inter action of artificial intelligence and automatic control, some significant developments in the use of artificial intelligence tools for process control have been achieved (Astrom, 1986; Pinto 1988; Fahrenkrog, 1988; and Porter 1987). The modern control theory has made important advances. And, although successful in some applications, it has failed to cope with the practicalities of many industrial processes. As a result, the automatic operation of a plant has been confined to a small region around a normal operating point and to periods without any great disturbance. One of the main reasons for this is the lack of accurate and structured knowledge of the processes involved. Despite this, operators applying their knowledge, experience, and a little intuition, often obtain good results controlling the plant in such situations. Considering the above, the next obvious step is to include similar reasoning capacities in a computational system. The development of such an expert supervisory system prototype applied to a mineral crushing plant is presented. Problem description The problem is to conceive a control system with the ability to handle quali-

Jan 1, 1989

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2&apos;-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0&#183;lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of &quot;barren liquor&quot;, free from &apos;uranium, are at present run to waste. This &quot;barren liquor&quot; results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961