Search Documents

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By A Webster, T Murphy

Block cave mining, in its broadest sense, has transitioned from an orebody/rock mass determined method of extraction, to a low-cost and high production mining method that may be applied to any large ore deposit. This inherently means that caving is now required in more complex rock mass conditions where assistive damage, through preconditioning, may be necessary. This requires comprehensive understanding of the geology, and its interwoven relationship with geotechnical parameters, and is made more challenging due to limited exposure in block cave mines. Limited mine development throughout the cave volume equates to a heavy reliance on drilling data in terms of observations, modelling of the mine geology, and collection of geotechnical data. This translates as increased uncertainty of geological and geotechnical models and has potential to impact significantly on the ability to make informed decisions in the design and operation of the cave mine.Modelling of cave propagation behaviour requires a complex, coupled system of draw of material, flow of material through the cave stocks, and propagation of the cave-back assisted by autogenic stress-related breakage of the rock mass, manifested as seismicity. The role of geological features in the process of cave propagation is not well understood and requires evaluation on a mine-specific basis, given the diversity of geological controls/settings of ore deposits and local variability of stress fields.Seismic monitoring systems can elucidate key geological features and domains, as heterogeneous seismogenic activity is observed ahead of the advancing cave-back. The observations made from analysis of seismic monitoring data may have potential to be used as a validation tool for numerical modelling of predicted cave behaviour in similar geological settings (eg next lift/panel).Understanding of the geological structure, at all scales, is critical to optimise the design and operating decisions made in a block cave operation. At present, intermediate-scale structure, anisotropy, mineralogy and model uncertainty may be neglected or under-represented despite their likely significant role in the mechanisms of cave propagation.Insights from an analysis of the Ridgeway Deeps block cave mine are discussed in this paper.CITATION:Murphy, T, Webster, A and Chitombo, G, 2016. Beyond rock mass characterisation – the impact of geology on block cave mining, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 861–872 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. A. Cramer

South African platinum mines produce the world?s majority of platinum metal that is used in autocatalysts and jewellery. As the platinum market is forecast to grow at healthy rates into the future, the South African producers, Anglo Platinum, Impala, Lonmin and Northam, are planning to expand in the next decade. Furthermore, a number of smaller producers who are accessing other mineral rights are entering the buoyant market. The South African platinum mines have traditionally exploited the Merensky Reef of the Bushveld Igneous Complex (BIC); however, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the orebodies at deeper levels. In the past decade all of the producers have begun to mine the less attractive UG2 reef because of its cheaper mining costs. This UG2 reef contains significant quantities of chromite with typically a chrome-to-iron (Cr/Fe) ratio of 1.35. UG2 ores can contain between 10 and 25% Cr2O3dependingupon the reef width and the selected mining method. It is relatively cheap and easy to extract a portion of the chromite from a platinum concentrator tailings stream at a grade of between 40?42% Cr2O3. However, it is only in recent years that some ferrochrome producers have begun to source some of their chromite from the tailings of platinum producers. South Africa is also the world?s largest single producer of ferrochrome and supplies much of the world?s stainless steel producers and thus the growing market for their product. As the traditional sources of high Cr/Fe ratio ores have been depleted at the shallow economic depths and thus have become more expensive sources of chromite, technical developments have improved the ability to use fine chromite economically to make acceptable grades of ferrochrome. Thus UG2 fines are now becoming possible cheap sources of acceptable feed to the ferrochrome industry. The abundance of feedstock for ferrochrome production and the lessening dependence on mined material will impact upon the structure of the ferrochrome business in South Africa. With continued platinum mining from UG2 reefs, South Africa is set to remain highly competitive in the world?s ferrochrome/stainless steel industry.

Jan 1, 2004

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By J. -P. Gisiger

On the basis of laboratory test results a comparison of various parameters (unconfined compressive strength, CERCHAR and LCPC abrasivity indexes, mineralogy) is presented and discussed in order to outline certain correlations between them. Samples cover a wide range of lithological types coming from various sites of tunnels. A partir de résultats d’essais de laboratoire, une comparaison de divers paramètres (résistance à la compression simple, indices d’abrasivité CERCHAR et LCPC, minéralogie) est présentée et discutée dans le but d’en tirer certaines corrélations. Les échantillons couvrent un large éventail de types lithologiques provenant de plusieurs sites de tunnels. Basierend auf Laborversuchen, werden verschiedene Gesteinseigenschaften (Druckfestigkeit, CERCHAR und LCPC Abrasionsindexe) präsentiert und Korrelationen aufgezeigt. Die untersuchten Proben verschiedenster Lithologien stammen aus mehreren Tunnelprojekten.

Jan 1, 2003

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Diego Corrêa Magalhães

Com o objetivo de encontrar uma solução inovadora e de baixo custo para o tratamento de efluentes domésticos, foi desenvolvido e implementado na ArcelorMittal Tubarão um sistema de tratamento utilizando escória de aciaria LD. O sistema, que se compreende de um Tanque de Recebimento; Tanque de Sedimentação; Filtro de Escória; e Redutor de pH foi objeto de estudo e teve sua eficiência medida em relação a sete fatores: Demanda Química de Oxigênio, Demanda Biológica de Oxigênio, E. Coli, Fósforo Total, Fósforo Dissolvido, pH, e Sólidos Suspensos Totais. De maneira geral, o sistema mostra-se eficiente, com destaque para as excelentes taxas remoção de E. Coli, Fósforo Total e Fósforo Dissolvido. O controle do parâmetro pH através de um método de baixo custo ainda representa um fator a ser superado, que quando consolidado permitirá uma nova aplicação para o material no tratamento de efluentes domésticos e rurais.

Aug 16, 2017

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By Miller F. S

The famous Golden Mile of Kalgoorlie in Western Australia was, between 1888 and 19ft, one of the richest and most important gold camps in the world. Annual production, which reached a peak of nearly 1,300,000 oz. in 1903, however dropped to below 400,000 oz. after 1920.Depression seized the camp, and many mines closed down. The output from this old field is now steadily mounting under the stimulus. of a higher price for gold. In 1935 300,000 oz. of precious metal were recovered and the future is bright. Total production from the field is 21,400,000 oz., whereas something like £23,600,000 have been paid in dividends.The Golden Mile has been studied by many geologists. Their somewhat diverse findings were published for the most part in the Australian technical press which, unfortunately, is not sufficiently represented in foreign libraries.The following article is based on an eighteen months' study in the district for Gold Mines of Kalgoorlie Ltd., preceded by four years' experience with almost identical rock types in the, Porcupine district of Ontario. The excellent record of observed fact left by previous invesigators, augmented by talks with observant mining men...

Jan 1, 1937

By G J. Corbett, P Magner, M McKenzie

Structures formed during ductile deformation have been reactivated during the later brittle mineralisation process. Two generations of folding are classified as: early recumbent megascopic FI folds and FI shears which transpose the hinge regions, and later upright F2 folds. S1 is folded about F2 folds which contain axial planar S2 crenulation cleavage. Vergence relationships between S1 and bedding indicate that many of the mineralised structures occupy sites of FI folds which have acted as plumbing systems for later gold mineralisation (eg Blackwater mine). The Globe-Progress gold mineralisation is localised by a major jog formed by sinistral strike-slip movement on two FI fault segments and mineralisation also occurs in smaller jogs along strike (eg Sir Francis Drake, Happy Valley-Merrijigs, Cumberland).   The lodes of ribbon quartz which exploit the FI shears and local bedding planes, are inferred to have mostly formed after the peak of metamorphism, possibly related to the emplacement of Carboniferous granites. This was followed by a sequence of vein deposition and wallrock alteration which consists of quartz-As/Fe sulphides ? carbonate - stibnite ¦ trace base metal sulphides and Bi-sulphosalts ? illitic clay/sericite-chlorite. Gold at Globe-Progress is mainly encapsulated in arsenopyrite. At Blackwater, free high fineness gold occurs in partings in lode quartz with late sericite-chlorite. The above sequence of events is comparable to that encountered in many intrusion-related gold systems throughout the Southwest Pacific region. There is a spatial relationship between gold mineralisation and dykes variably described as diabase, dolerite or lamprophyre. Alkaline rocks occur in many Pacific rim and older goldfields and may possibly be related to a magmatic source for gold mineralisation.

Jan 1, 1997

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By E. E. White

(Cleveland Meeting, October, 1912.) IN, August, 1911, I read a paper before the Lake Superior Mining Institute' on surveying and sampling diamond-drill holes. The present paper gives a more thorough description of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drill-holes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-bole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a 1 Proceedings of the Lake Superior Mining Institute, vol. xvi., pp. 100 to 120 (1911). 2 Recent Practice in Diamond-Drilling and Borehole Surveying, Bulletin No. 91, Institution of Mining and Metallurgy (Apr.. 11, 1912).

Nov 1, 1912

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012