Search Documents

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By AIME AIME

THE American Engineering Council, which is the working body of The Federated American Engineering Societies, held its first meeting in Washington, Nov. 18 and 19, 1920. The Federated American Engineering Societies was formed in Washington in June and is composed of engineering and technical societies, national, state, local and regional. These Member Societies elect delegates to the American Engineering Council, which is the administrative body of the Federated. The meeting was called to order by Richard L. Humphrey, Chairman of the Joint Conference Com¬mittee, and the program (which is printed below) was carried out without substantial change by E. S. Carman, who was elected temporary chairman. Under the Constitution, the Council appoints an Executive Board, the members of which are chosen according to the proportional membership of the vari¬ous Member Societies in their respective districts. Under this plan, with the present membership, 'the national societies will have 14 members and the local societies 6 members on the Executive Board.

Jan 1, 1920

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine's capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces' upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By A. Schaum

On average, there are approximately 10 fatal haul truck accidents per year. The most common causes for haul truck accidents include mechanical problems, inadequate training and insufficient road/berm maintenance. Due to the frequency and magnitude of haul truck accidents, new training methods are being investigated. With the widespread availability of computers and new technology becoming more reasonably priced, the ability to incorporate computer-based training for miners is becoming more possible. It has been shown that computer-based training is just as effective in knowledge acquisition as traditional lectures, and computer-based training can lead to a significant increase in the retention of material (Williams and Zahed, 1996). Studies have also shown that more engaging training methods lead to more effective knowledge acquisition (Burke et al., 2006). A supplemental system for current and new miner training to address the common causes of fatal accidents was developed. The training system is a virtual preshift inspection of a haul truck, and it can train new haul truck operators to identify parts that look defective. The training will increase an operator?s ability to recognize problematic parts and correctly identify the corrective action needed. Increasing the quality of training by providing an engaging, simulated hands-on environment will lead to safer behaviors by trainees, which will ultimately lead to fewer accidents and fatalities.

Jan 1, 2008

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By John D. Foulkes

A study to categorize and characterize underground metal/non-metal mining operations from the viewpoint of telecommunication requirements and practices. The objectives were to: ? Gather and analyze data; ? Identify communication requirements; and ? Recommend systems for operational emergency and post-disaster telecommunications.

Jan 1, 1979

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

Differentiation of a basaltic (?) magma occurred in an active volcanic area during the late Miocene and Pliocene, and a change in the general mode of extrusion from fissure flow for the basalt to explosion for the andesite reflects an accompanying increasing magmatic viscosity. A caldera formed after the flow phase was completed and was filled with coarse agglomerate, much of which has a fused appearance. After an erosion interval its shape was modified and it became gradually deeper as repeated explosions from growing andesitic volcanoes caused large quantities of pyroclastic material to be deposited. At the close of this phase the floor abruptly collapsed when a, large block of the underlying crust was engulfed. The incompetent pyroclastics filling the caldera steepened in dip and the ensuing fractures were filled by the rising magma as dykes and sills and a chonolith formed below the caldera at a shallow depth. The ensuing activity reveals a further stage in differentiation and biotite is an important new ferromagnesian to be observed in the new rocks.Fracturing of the surrounding basalts was most intense in the rocks forming the periphery of the caldera where steeply and flatly dipping faults resulted from increasing horizontal pressure directed towards the caldera.Further differentiation resulted in the increased crystallization of orthoclase felspar, as evidenced by the numerous intrusives of trachy andesitic composition. Magmatic freezing caused mineralizers to accumulate at the top of the chonolith. These eventually escaped and auriferous pyrites, tellurides, quartz, and calcite were deposited in the surrounding rocks.The flatly dipping fractures are the most important and can be expected at various depths in a zone about 4,000 ft wide surrounding the caldera. Latest movement along these was controlled by magmatic consolidation rather than the shape of the caldera. Some flat faults were able to remain open during mineralization and acted as a feeder for the shallower fractures, thus limiting the depths to which the steeper dipping fractures were mineralized with the possible exception of one particular Nw.-striking lode (the Crown-Crescent).INTRODUCTIONThe gold deposits of the Tavua district were discovered in 1932 and from 1935 to June, 1961, 1,985,041 fine ounces of gold were produced from 4,202,504 tons of ore. Of the original three producers, only the Emperor remains active in the...

Jan 1, 1962

By Luis Romero, Edilberto Linares, Steve Windle

El yacimiento de Zafranal —proyecto de pórfidos de cobre y oro ubicado en la región Arequipa, Perú— en sí mismo ha penetrado en lo que parece ser un salto dextral sobre una estructura del SFIC. A nivel de yacimiento, se ha mapeado una serie de fallas pronunciadas WNW en la zona mineralizada principal, consistentes con la transtensión dextral inferida. Esta estructura de fallas se trazó en 3-D a partir de las zonas de gubias identificadas en la fotografía de testigos, método que permitió elaborar un modelo estructural de forma rápida y con consistencia interna. La cinemática de las vetas y los patrones de afloramiento trazados generalmente coinciden con las estructuras interpretadas. El movimiento dextral inferido en el SFIC en el Cretácico Superior es consistente con un vector de convergencia de placas hacia el norte, y puede ser utilizado para identificar targets estructurales para sistemas de edad similar, tanto en el piamonte como en la cordillera.

Dec 31, 2019

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By J Wallis

The stability of a raise bore is often assessed using the rock mass classification system published by McCracken and Stacey as a modification of the Q system. Often the assessment is done using a spreadsheet to manipulate geotechnical log(s) of boreholes. This paper discusses the inherent difficulties with this approach. Recent work by others to provide guidelines to the classification system is discussed. A recent example of the design and raise bore performance at Macraes Gold Mine, New Zealand is presented. A key issue is that a visual assessment of the drill core and/or core photographs is necessary to æground-truthÆ the classification.

Jan 1, 2008