Search Documents

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

By C Vuillier, A Roshdieh

Water is the main medium for removing impurities from iron ore during wet processing to achieve a higher quality product. However, there is a substantial increase in freshwater consumption due to an increase in demand from the following two factors: in the past 55 years the world population has doubled from 3 to 7.5 billion and crude steel production has increased five times from approximately 350 to 1662 Mt/a (IISI, 2008). Furthermore, social development in developing countries exacerbates water consumption making freshwater an increasingly valuable resource with an average distribution of 70 per cent for agriculture, 20 per cent for industry and only ten per cent for domestic consumption (Hourtolle, 2005; OECD, 2009). Rapidly changing regulations over the access and preservation of water across the world indicates the growing importance of this issue, so the mining industry must adapt to this continual change and must be committed to increasing the efficiency of water usage.Tailings dams receive most of the water used by the process plant. In arid regions where evaporation is high and availability of water low or non-existent, technical solutions other than the conventional tailings dam, such as thickened and/or filtered tailings, exist to optimise the recovery of water and reduce the need for external water consumption. However, these solutions present additional challenges, such as energy consumption and transportation from the process plant to the ultimate storage area.This paper considers a range of alternatives covering thickening and filtering, transportation and storage, water return, closure and rehabilitation. Mining projects in the future will be more affected by the rising cost in water and tighter regulations in accessing water and energy. Good tailings management can contribute significantly to reducing the dependence on these two key commodities (water and electricity), improving the resilience of iron ore projects especially in arid regions and areas with high competition for water.CITATION:Vuillier, C and A Roshdieh, A, 2017. Minimising the water loss associated with mine tailings disposal, in Proceedings Iron Ore 2017, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By José Carlos D?Abreu

The Tecnored process is a new ironmaking technology, developed on a unique approach that combined empirical and theoretical knowledge backed by extensive tests carried out in a dedicated pilot-plant and with close support of universities and research centers. Campaigns in the pilot-plant focused on operate different reactors of different sizes, including a full size slice of the industrial furnace. This approach provided actual conditions to develop the main features of the process such as the internal dimensions, raceway pattern, thermal and gaseous profiles, etc, besides provide reliable data to feed and calibrate a specific mathematical process modeling. This paper presents the first computer model used by the Tecnored technical staff, focusing the behavior of a self reducing agglomerate in the upper shaft of the furnace (zone of solid state reduction). Some results of this model are given and discussed.

Jan 1, 2006

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

A simple process for making filter aids from coal by controlled carbonization at 800-1200·C is described.Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization.Product yields depend upon the composition of the parent coal but are always less than the sum of the ash and fixed carbon values determined by the proximate analysis. The product yield also depends on the air-to-coal ratio, which affects the amount of coal substance burned and the temperature attained. Particle residence time and reactor temperature affect the degree of devolatilization of the product and hence its wettability. The filtration behaviour of carbonaceous filter aids is greatly influenced by the size distribution, shape and physical properties of the particles-parameters which are largely determined by fue type and particle sizing of the coal used.Carbonaceous filter aids are distinctly different from other types commonly used and extensive industrial applications are anticipated in a wide range of industries ranging from food to mineral processing.

Jan 1, 1970

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By Fred D. Fox

Introduction Abandoned mill tailings deposits can be found throughout the northern Black Hills of South Dakota, indicative of mining activities that originated during the great gold rush days of 1875. The Refuse Act of 1899 attempted to regulate the deposit of debris from mines and stamp works. But, in most cases, huge volumes of mine and milling wastes were disposed of in ways no longer considered environmentally acceptable. Restoration of gold mill tailings deposits is a relatively new practice to the Black Hills area. This discussion will present an overview of the environmental setting, environmental problems associated with past tailings disposal practices, practices being implemented to solve these problems, and prospects related to present the future tailings disposal practices. Environmental Setting An understanding of climatic characteristics, geology, surface and ground water hydrology conditions, and the physical and chemical characteristics of selected mill tailings deposits will aid in understanding environmental problems associated with tailings disposal and restoration. Climate The Black Hills region is in the middle latitudes, which have a

Jan 11, 1984

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

The mining industry in Australia frequently uses the services of specialist engineering and managing contractors and consultants for a majority of the work required for project development, from feasibility studies to project commissioning. The project owner's prime objectives are to achieve predictability and competitive advantage for their project. As the majority of this work will be carried out by contractors, the effective evaluation, selection and management of these contractors in the most appropriate forms of contracts is an essential ingredient to project success. The first stage to project development should be for the owner to examine its own resources to establish the role that it will fill and thereby identify the role and scope of contractors' involvement. Once the owner has developed this work plan, the selection of contractors and consultants should be structured to ensure that the owner acquires the appropriate expertise and experience to achieve its project objectives. The sequence of selection procedures is: 1. Pre-qualification of prospective contractors according to the owner's adopted criteria, through the use of a pre-qualification questionnaire. 2. Evaluation by the owner tender board according to predetermined mandatory criteria. 3. Preparation of tender documents for submission to qualified contractors. 4. Evaluation of tender submissions by the owner tender board using a pre-determined, weighted matrix of technical and commercial criteria. 5. Final selection and contract negotiation.

Jan 1, 1990

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By P. Oyanader

"In 2001, the Catholic University of Chile undertook a maintenance benchmarking study of six open pit copper mines having mill capacities varying between 18,000 t/d and 156,000 t/d, and collectively responsible for 58% of Chilean copper production. This paper describes the methodology used to conduct the study, as well as the overall results. Key performance indices were selected to measure the effectiveness, efficiency, and development of the maintenance process. Using a balanced scorecard philosophy, these indicators were divided into client satisfaction, financial, internal process, and learning and growth indices.Maintenance was found, on average, to be responsible for 44% of mine production costs. Percentage planned maintenance of equipment fleets was found to be low by world standards, averaging 35%, 56%, and 44%, respectively, for blasthole drill, shovel, and haul truck fleets. Fleet availabilities were found to be significantly influenced by the percentage of planned maintenance achieved, while maintenance cost per equipment was found to decrease non-linearly with increases in percentage planned maintenance. Investment in technical training (including planned maintenance practice) was found to be low by global standards. The paper concludes that fleet availability and maintenance costs in Chilean open pit operations could be considerably improved by improving and/or developing maintenance planning standards, and investing in training personnel in planned maintenance techniques"

Jan 1, 2005

By M D. Melville, B C. T Macdonald, J Dixon

The acidic and metal rich waters that are generated from acid sulfate soil (ASS) drainage can have damaging impacts upon ecosystems. The most obvious impact has been the discolouration of water and occasional fish kills. ASSÆs produce these acidic and metal rich waters when pyrite in soil is oxidised. Land management techniques are an essential long-term requirement to minimise the amount of pyrite oxidation. Acidic water that cannot be prevented through land management can be neutralised by other techniques. Powdered lime is the most common material in agriculture that is applied directly to soils and waters. Powdered lime can be expensive and if applied dry it may aggregate. Since the aggregated particles of lime are larger they could sink rapidly in the water column and not react. In waters with high concentrations of dissolved iron and aluminium the lime particles may become coated with a metal oxy-hydroxide precipitate, which will decrease its reactivity. A unique lime-dispensing machine, the Waterways Lime Spreader, has been developed to neutralise acidic waterways. The Waterways Lime Spreader can produce a solution rich in fine lime from larger limestone fragments. The current size of the machine means only 3.5 grams per second of limestone can be emitted. This output will neutralise low acidity waters, however, for high acidity waters the time for neutralisation can be long. More reactive chemicals such as hydrated lime or increasing the size of the machine will reduce this neutralisation time. The Waterways Lime Spreader is also capable of producing slurry mixtures if powdered materials are required. Trials with the Waterways Lime Spreader were undertaken in part of the Clothiers Creek catchment located in northeast NSW, Australia. A small drain with a water volume of 4 m3 was neutralised with crushed limestone to pH 6.9 from an initial pH of 2.6 and an acidity of 902 mg/L CaCO3 in 160 minutes. In comparison a drain with a slightly larger volume of 6 m3 that had an initial pH of 3.2 and an acidity of 753 mg/L CaCO3 was neutralised with hydrated lime to pH 11.8 in five minutes. The Waterways Lime Spreader has been used successfully to neutralise water from acid sulfate soils. It is expected that future applications of the machine may be for the neutralisation of acid rock drainage or acidified lakes.

Jan 1, 2003

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By Neil T. Davie, Thomas K. Blanchat, Thomas C. Togami, Joe R. Weatherby, Dale S. Preece, Robert A. Benham, James J. Calderone

"Geotechnical structures ,such as underground bunkers, tunnels, and building foundations aresubjected to stress fields produced by..the gravity load on the structure and/or any overlyingstrata. These stress fields may be.. reproduced on a scaled model of the structure byproportionally increasing the gravity field through the use of a centrifuge. This technology canthen be used to assess the vulnerability of various geotechnical structures to explosive loading.Applications of this technology include assessing the effectiveness of earth penetrating weapons,evaluating the vulnerability of various structures, counter-terrorism, and model validation. Thisdocument describes the development of expertise in scale model explosive testing ongeotechnical structures using Sandia’s large scale centrifuge facility. This study focused onburied structures such as hardened storage bunkers or tunnels. Data from this study was used toevaluate the predictive capabilities oft existing hydrocodes and structural dynamics codesdeveloped at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA)."

Jan 1, 1998

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011