Search Documents

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By D. R. Nagaraj

The traditional (popular) approach to reagent development and optimization, which has become entrenched in both research and practice for many decades, is highly reductionistic, incremental and costly, does not produce robust chemical solutions, and is not sustainable. There are also several other key drivers and changes in the mineral industry that clearly warrant a new approach. In response to these, an intense effort was made at Cytec over the past fifteen years to develop a meaningful, efficient, and sustainable approach to develop new reagents and robust chemical solutions in mineral separations. This effort culminated in three important outcomes: a) development of the holistic approach, called FLOTATION MATRIX 100? process, b) novel reagents, and c) enhanced application knowledge for reagents. In this paper, the efficiency, utility and power of the holistic approach will be demonstrated with examples using both existing and new reagents in the processing of Cu-Au, Au and Cu-Mo ores.

Jan 1, 2014

By T X. Le, H T. Tran, K Zaw, T Manaka

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Truong Son fold-thrust belt (TSFTB) is a prominent tectonic component of mainland Indochina that occurs as a north-west–south-east-trending tectonic entity that extends from north-eastern Laos, straddles the Laos-Vietnam border area and is submerged under the sea basin in east central Vietnam. The TSFTB hosts numerous regional-scale gold and polymetallic base metal deposits, and the mineralisation occurs along the strike of the belt; however, the potential of many of these deposits are inadequately evaluated. The ore mineralisation is hosted by different rock assemblages, including highly metamorphosed Late Proterozoic metasedimentary rocks and Palaeozoic sedimentary and/or volcanic packages, which were intruded by several phases of magma and underwent a number of tectonic events. Several ore-forming styles – including porphyry, Carlin-type and sediment-hosted orogenic Au – were formed during at least two phases of regional thermotectonism that have been identified in the TSFTB. However, all of the major gold deposits/mineralisations are closely related to region-wide structural breaks and many of them are controlled by large-scale, high-strain zones. The fold-thrust structures in the TSFTB therefore play important roles for regional gold mineralisation and metallogeny.CITATION:Tran, H T, Zaw, K, Le, T X and Manaka, T, 2015. Structural controls on gold mineralisation in the south-eastern Truong Son fold-thrust belt and its significance in regional metallogeny, in Proceedings PACRIM 2015 Congress, pp 521–530 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By R. W. Huber

A consumable-electrode arc-melting furnace was constructed at the Bureau of Mines Physical Metallurgy Laboratory, College Park, Md., for the production of uncontaminated titanium and titanium-alloy ingots. The furnace was designed to allow for evacuating to very low pressures and back filling with helium and argon mixtures for melting at or near atmospheric pressure. Vacuum melting at a few millimeters pressure was also used with a mixture of helium and argon gas sweeping the crucible. For research purposes a 25- to 30-pound ingot, 4 inches in diameter by 15 inches in length, was selected to provide, enough 1/2-inch plate for extensive tensile and impact testing of standard size specimens. Enough plate was also provided for testing by other Government laboratories. The homogeneity of several alloy ingots was determined, and excellent results were obtained. By using a large electrode-to-ingot-area ratio and high currents or power inputs to the arc furnace rather uniform ingots were routinely prepared.

Jan 1, 1957

By Cory McElprang, Enamul Hoque, Aaron Thomas, Scott A. Jacobs

Crosshole Sonic Logging (CSL) only evaluates concrete on the inside of reinforcing cages leaving the outside unevaluated unless other types of testing are performed such as Perimeter Sonic Logging (PSL). While there have been some reports of PSL testing having accurately identified anomalies (e.g. Samtani et al 2005), experience by Case Foundation Company has indicated otherwise where false positives were determined with subsequent coring. Numerous cases of PSL false positives are presented as well as a study where a shaft was installed with both inside and outside tubes, and CSL and PSL data were compared. To date, there is very limited data published on perimeter sonic logging, or Gamma-Gamma Logging (GGL) with tubes on the exterior of drilled shafts. Several cases will be presented where false positives were experienced where PSL testing was performed. In addition, a direct comparison will also be presented where a shaft was installed with both tubes on the inside and outside where CSL and PSL data is compared. BRIEF HISTORY – CSL TESTING AND TUBES ON INSIDE The general procedure of Crosshole Sonic Logging (CSL) testing includes attaching tubes to the reinforcing cage to be able to send a transmitter in one tube and a receiver in another tube with which a sonic pulse is emitted from the transmitter and received in another tube. The time taken for the sonic pulse to travel between the tubes is measured and compared to expected values for the known distance between the tubes. Any increase in time from expected values indicates the sonic pulse traveled through a media other than homogeneous concrete such as objects in the path (spacer wheels, steel bracing, etc.), tube spacing, or soil inclusions. However, variations in arrival time can also result from differences in concrete density. The tubes have traditionally been placed on the interior of the reinforcing cage which protects them during hoisting and placement of the cage and reduces wave refraction caused by modulus of elasticity differences between steel and concrete. This allows the concrete within the interior of the reinforcing cage to be evaluated, but the concrete outside of the cage is excluded from traditional CSL testing. As a result, alternative integrity testing has been developed to not only provide different ways to evaluate the integrity of drilled shafts but to also address the issue of evaluating the concrete outside of the reinforcing cage. These alternative testing methods include Gamma-Gamma Logging (GGL), Thermal Integrity Profiling (TIP testing) and Perimeter Sonic Logging (PSL) which is similar to CSL testing but instead of the tubes placed inside the reinforcing cage, the tubes are placed on the outside of the reinforcing cage as shown in Fig. 1.

Jan 1, 2019

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By Mônica Aline Magalhães Gurgel

A partir de duas ligas de NiTi elaboradas em escala laboratorial e processadas via forjamento rotativo e fundição por sucção a vácuo (molde de cobre), suportados pelas análises de Microscopia Eletrônica de Varredura (MEV), Espectroscopia de Energia Dispersiva de Raio-X (EDS) e Calorimetria Diferencial de Varredura (DSC), foi possível observar que a fundição por sucção a vácuo resultou no mais significativo refinamento microestrutural e aparente homogeneidade microestrutural/ composicional, exibindo transformações de fase por DSC como fundida.

Oct 30, 2017

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By Arno C. Fieldner

Six years ago, I addressed the annual meeting of the American Society for Testing Materials on "Fuels of Today and Tomorrow."3/ Since then, our country has been drawn into another great war of veritably global extent, with unprecedented demands on fuels, foods, and materials in general. My purpose in this address is to review the changes in fuel supply and demand since 1937 and to give you my views on the outlook for the future. CONDITIONS IN. 1237 Daring 1936 the United States produced and consumed one-third of the world production of coal, two-thirds of the petroleum, and about 95 percent of the natural gas. Two-thirds of the oil produced in all countries since the discovery well was drilled in 1859 had come from American wells. With the exception of the three depression years 1931, 1932, and 1933, new oil reserves were being discovered since 1924 well in excess of our increasing rate of consumption. Discoveries of natural gas, likewise, were tremendous in volume, and this fuel was being transported to most parts of the country by pipe lines; some of them more than 1,000 miles long. We had all kinds of mineral fuels in abundance and at prices that did not stint anyone in the maximum utilization of the mechanical devices that were being developed on every hand. No one suspected that the time might come in a few years when, gasoline would be doled out to some of us at the rate of 1-1/2 gallons a week or that many of our fuel-oil furnaces would have to be converted to burn coal. Of course, these restrictions are due to unusual war conditions, such as lack of coastwise tanker transportation, unprecedented demand for aviation gasoline, and the shortage of rubber for automotive tires. However, these shortages do call our attention to the vital part of petroleum reserves in our country's future position among nations. Therefore, it is of special interest to review briefly the relations of recent supply and demand with respect to our various mineral fuels.

Jan 1, 1943

By Saulo Brinco Diniz

O presente trabalho faz a caracterização microestrutural e mecânica da liga de alumínio 3105 submetida a duas técnicas de Deformação Plástica Severa (NECAE - Extrusão em Canais Não-Equiangulares, e Laminação Assimétrica), a fim de se eleger entre as duas técnicas a melhor para se obter uma microestrutura mais encruada e refinada. As avaliações microestrutural e mecânica foram feitas por Difração de Raios-X (DRX), análise dilatométrica e ensaio de dureza Vickers, as quais permitiram avaliar de forma indireta o grau de encruamento / refinamento da estrutura resultante de cada processo de Deformação Plástica Severa, avaliando o incremento de dureza, perfil do pico de DRX e temperatura de início de recristalização. Conclui-se que a técnica mais efetiva no encruamento/refinamento da estrutura foi a Laminação Assimétrica, tendo em vista a geometria adotada na técnica de NECAE.

Aug 7, 2018

By Donald L. Everhart

The National Uranium Resource Evaluation (NURE) program since 1974 has been designed to accomplish a comprehensive coverage of the 48 conterminous States and Alaska to evaluate the total uranium resources of the USA. This resource base includes both ore reserves and potential resources. Techniques include airborne radiometric and magnetic surveys, by hydrogeochemical surveys, surface and subsurface geologic studies, and the application of improved geochemical exploration and resource assessment methods (Table 1). In brief review, the current status of each of the five basic NURE elements is as follows: In the Aerial Surveys, in the conterminous 48 states, the flying has been completed in 89 of the NTMS 10 x 2° NURE quadrangles, and is in progress in 39 more (Figure 1). Complete quadrangle data have already been open filed for 46 additional quadrangles, for a total of 174 for which data gathering is either complete or in progress. In Alaska, the flying is complete in 42 quadrangles, and quadrangle data have been open filed for 34 more, for a total of 76 (Figure 2).

Jan 1, 1979

By Carla Lupi

NiMH sealed cells (portable cells) are today widely used in all consumer applications replacing primary alkaline batteries: wireless mobile communication, portable computers and camcorders, are the largest application segments. The Italian market. of NiMH cells is steadily growing, following the impressive penetration rate of the cellular phones. The organization of a national collecting system and correct recycling process are the key factors to prevent environmental impact associated to these wastes, while the metal values recovery can improve the feasibility of the recycling process The University of Rome, Texeco Engineering S.d, and MO.SMO.DE. S.a.s. have developed a combination of mechanical and hydrometallurgical processing to recover Nickel, and Cobalt salable products and rare earths intermediate products. A new plant located in South Italy, designed after this technology, is able to recycle waste Ni-MH batteries collected in the Italian territory, together with other industrial and portable batteries based on different chemistries. The process is able to treat both individual cells and plastic power packs and includes as basic steps an original crushing and elutriation treatment to separate plastic, metallics, and active mass components that are subsequently treated by a hydrometallurgical process to recover Ni, Co, and RE. The hydro metallurgical main steps are: acidic leaching, RE separation, multistage precipitation of Ni, Co and Fe and final solvent extraction on dissolved Ni and Co salts. For each operation the operative condition have been determined.

Jan 1, 2000

By A. W. Fahrenwald

FLOTATION practice in Idaho is now about 13 years old. The advance has been steady during these 13 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. ORES OF THE DISTRICT The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a-specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

Why A Friction Hoist? B EFORE discussing the equipment, it would be instructive to review the factors that influenced the management of Opemiska Cop-per Mines to purchase a friction hoist rather than a conventional double drum hoist. The mine required that 250 tons per hour be hoisted from a depth of 2,100 feet. They also specified that the top speed should not exceed 1800 feet per minute. Eight ton capacity skips in balance and a maxi-mum hoisting speed of 1725 feet per minute would meet the required <Output on a duty cycle as follows: Loading time Creep away from loading pocket Accelerate (at 2.5 ft/sec2) 10 seconds 5 seconds 11.5 seconds Full speed run Decelerate (at 2.5 ft/sec2) Creep into dump Cycle time Trips per hour Tons per hour 72 seconds 11.5 seconds 5 seconds 115 seconds 31 31x8 = 248

Jan 1, 1962