Search Documents

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

By Jr. Frost

Helium used as a tracer gas in petroleum reservoirs continues to show great promise as a new tool for the oil and gas industry, according to tests conducted jointly by the Bureau of Nines and The Pure Oil Co. in-the Cabin Creek field, Boone and Kanawha Counties, W. Va. Helium, when used as a, tracer gas, is mixed with natural gas being injected into a reservoir for secondary recovery of oil, recycling, pressure-maintenance, or other purposes. Three separate experimental helium tracer-gas tests were run in the Cabin Creek, W. Va., field, wherein helium was added as a tracer to the natural gas that was being injected into the oil-bearing Berea sandstone. The results obtained in each test permitted determining the direction and rate of travel of the injected gas, calculating the volume of injected gas in the gas produced at the various wells, and determining the nature of the transition from natural gas to injected gas during a gas-injection program. Data were obtained on the effects obtained from waves of injected gab containing 1 percent and containing 5 percent helium and from a wave of essentially pure helium injected into the formation.

Jan 1, 1950

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Eldon C. Pattee

THE BUREAU OF MINES began an investigation of tungsten resources of Montana in September 1953. This report presents information obtained from July 1955 to September 1957 on tungsten deposits in and near the Mount Torrey batholith. The batholith comprises part of the Pioneer Mountains of Beaverhead County in the southwest corner of Montana. Included in the report are assays and preliminary-examination data on 22 properties. Tungsten minerals are known to occur in 19 of the properties. The major producer is the Brown's Lake mine which has produced more than 625,000 tons of ore. Nearly all of the deposits are in the Lost Creek, Utopia, and Bald Mountain mining districts along the east and south margins of the Pioneer Mountains. The districts are less than 27 miles from Dillon, Mont.

Jan 1, 1960

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

By M Hourn, G Anderson, V Lawson, P Voigt, D Mallah

As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flow sheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particularly under threat. The economics of such operations are far more susceptible to metal price fluctuations, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most economic effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is often overlooked is how a hydrometallurgical process could also be integrated in the overall flow sheet to achieve higher overall recovery at the mill. In the base metals environment, this is probably because hydrometallurgical processes are associated with production of metal, or require the use of expensive and toxic precipitating agents once the minerals of interest are in solution. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams. Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams and also tailings streams to complement a concentrator flow sheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middling concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows the plant to operate on a more favourable part of the grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added to the flow sheet with no process interruptions. Two case studies are examined showing flow sheets and costings to arrive at the value proposition of the GT low grade treatment flow sheet.CITATION:Voigt, P, Hourn, M, Lawson, V, Anderson, G and Mallah, D, 2017. Economic recovery and upgrade of metals from middling and tailing streams, in Proceedings MetPlant 2017, pp 289–297 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"DIGREGORIO, K. A., E. V. CILENTO, AND R. C. LANTZ. A kinetic model of superoxide production from single pulmonary alueolar macrophages. Am. J. Physiol. 256 (Cell Physiol. 25): C405-C412, 1989.-A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared with experimental results obtained from single rat PAM. The 02 was quantified by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate (NBTH,) from video-recorded images of individual cells. The kinetic model considered three reactions: 1 ) the production of extracellular 02 from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, 2) the subsequent dismutation of 02 to form H,O,, and 3) the reaction of 02 and NBT to form diformazan. NBT specificity for 02 was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) that catalyzes the dismutation of 02 to H,O,. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations because NBT is a relatively small molecule (818 mo! wt) compared with SOD (34,000 mol wt). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/ or electrostatic effects, since SOD is also negatively charged, whereas NBT is positively charged.PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria. This process is accompanied by the production of superoxide anion (02) at the surface of the plasma membrane (3, 31). Superoxide readily dismutates to form H20 2 and subsequently, other oxygen metabolites which have been shown to be both antibacterial and cytotoxic (21, 25, 35).Superoxide is produced from the reduction of extracellular O, at the surface of the cell membrane by NADPH oxidase by the following reaction (3, 4)"

Jan 1, 1989

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

ALABAMA Anniston.-Carrington, F. G. Auburn.-Brown, R. L. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Salmon, H. S. Schaber, C. F. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W, Ball, E. M. Bonnyman, J. Bowron, J. Bush, M. W. Crawford G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gallacher, J. Geisiner, H. S.

Jan 1, 1917

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965