Search Documents

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By George W. Toth

Uranium in situ leach mining has recently emerged as a viable alternative to conventional miring techniques. The cost implications of in situ mining are therefore of increasing interest to mining paracticioners as well as public officials. This report presents the results of an assessment of uranium in situ leach mining costs through the application of process engineering and discounted cash flow analysis procedures. A computerized wasting technique, termed a cost model, was developed through this effort to facilitate rapid cost analyses. Application of this cost model will generate mine life capital and operating costs as well as solve for economic production cost/lb. U308. Conversely rate of return may be determined subject to a known selling price. The data bases of the cost made! have been designed to reflect variations in Texas vs. Wyoming site applications. The results If applying the model under numerous ore deposit, operating, wellfield and extraction plant conditions for Texas and Wyoming are summarized in the report. Sensitivity analysis of changes in key project parameters have also been tested and reported.

Jan 1, 1981

By W. W. Adams, T. D. Lawrence

"A. larger enrollment and a greater number of man-hours of employment by the enrolled companies were the outstanding features of the National Safety Competition of 1942, an annual safety contest conducted by the Bureau of Mines, United States Department of the Interior, for the promotion of safety among workers in the mines and quarries of the United States. The accident-frequency and accident-severity rates were somewhat higher than in 1941, but the frequency of accidents in relation to the number of man-hours worked was strikingly lower than in the earlier years of the 18-year period during which the contests have been conducted.Companies that enroll in the National Safety Competition compete for a bronze trophy known as the ""Sentinels of Safety."" Six of these trophies are provided by THE EXPLOSIVES ENGINEER annually for award by the Bureau of Mines. The trophies for 1942 wore won by an anthracite mine in Pennsylvania, a lignite mine in North Dakota, an underground metal mine in Tennessee, a limestone mine in Ohio, an open-cut metal mine in Minnesota, and a lime-:tone quarry in Pennsylvania. The trophies are presented to the companies for 1 year and are then transferred to the winners of the succeeding year's contest.The contest rules state that a mine or quarry must have at least 25 men employed underground or in the pit for at least 100 days, and the plant must be in operation 30,000 or more man-hours to be eligible for a trophy. The rank of mines and quarries is determined by accident-severity rates, or, in the case of accident-free records, by the number of man-hours worked."

Oct 1, 1943

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By R. H. Storch, D. C. Holt

During reconnaissance investigations of more than 300 stream areas in Idaho to determine the potential value of ilmenite in black - sand placer deposits 46 deposits were explored by churn drilling , trenching , test pitting , or shafting . The component mineral content and total black - sand content were determined for more than 8,690 reconnaissance and exploration samples . Data compiled during the investigation indicate a good potential for large , low- grade deposits containing ilmenite , monazite , columbite , euxenite , uranothorite , and other radioactive black minerals and accessory black - sand minerals . The data also indicate most deposits will be economic only if several component minerals can be recovered as coproducts .

Jan 1, 1963

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By Lloyd W. Trevoy

Syncrude Canada Limited is presently studying commercial production of heavy minerals from plant tailings of the openpit A lhabasca tar sands operation. When tar sands are processed and upgraded to synthetic crude oil, heavy minerals can be removed f rom the extraction circuit and beneficiated to provide concentrates of zircon and titanium minerals. Calculated recovery rates indicate that crude oil production capabilities of 105,000 barrels per day would provide 26,000 tonnes of zircon and 114,000 tonnes of titanium minerals annually. The titanium minerals concentrate is a mixture of ilmenite, leucoxene and rutile; it could be used as recovered or upgraded to synthetic rutile. With the consrruction of further synthetic crude oil plants in Western Canada, a large reserve of heavy minerals will become available.

Jan 1, 1984

By R. S. Olsen

The Bureau of Mines is engaged in research to recover aluminum from kaolinitic clay and other nonbauxitic domestic resources. As part of this work, calcined Georgia kaolin was prepared by a process that prevents slime formation and makes the leached residues fast settling and easy to filter. The leaching reaction for calcined kaolinitic clay in a 5 pct stoichiometric excess of boiling 23-to 26-pct HCI was found to be zero order. Rate constants based on the weight-fraction of aluminum in the clay were found to be between 0.095 and 0.15 min-1 depending on feed preparation and leaching parameters. The mathematical relationships between aluminum extraction and time for both batch and continuous, stirred-tank operations were derived and verified experimentally.

Jan 1, 1983