Search Documents

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By J G. Brady

This paper discusses the ceramic products used in the construction industry in Canada, as well as the main raw materials used in their manufacture. The products include the! following: (1) clay prorlucts -such as facing brick (glazed and unglazed), common brick, facing tile (glazed and un-glazed), terra cotta, load-bearing tile, non-load-bearing tile, structural clay floor tile, quarry tile, drain tile, sew-er pipe, conduits .and flue liners -which are made mainly from domes-tic common clays and shales and from domestic or imported stoneware clays and low-grade fire clays; (2) floor and wall tiles of the whiteware type, which are produced from ingredients such as kaolin, ball clay, feldspar, nepheline syenite, talc, pvro-phyllite and wollastonite; (3) glass products -the major ones being sheet glass, plate glass and mineral wool (glass wool, and rock or slag wool) -which are made from such materials as silica sand, soda ash, salt cake, feldsspar, nepheline syenite, dolomitic limestone, high-calcium limestone. borax and (for rock and slag wool) various rocks or slags;

Jan 1, 1963

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010

By Maria do Socorro da Silva

Aços inoxidáveis são aços caracterizados principalmente por sua alta resistência à corrosão em diversos ambientes. Essa característica advém da formação de uma camada de óxido de cromo. A classe de aços inoxidáveis superausteníticos é derivada dos austeníticos pela adição de elementos de liga. A temperatura do ambiente de trabalho pode favorecer a formação de precipitados que podem afetar as propriedades mecânicas e de resistência à corrosão desses aços. Em decorrência da quantidade de Mo, Ni e Cr ocorre precipitação de fases secundárias, sendo mais comuns as fases sigma (s) e qui (c). Para caracterizar a microestrutura e formação da fase s nos superausteníticos, foram realizados os seguintes tratamentos térmicos de solubilização: 1170oC (para formação da maior fração volumétrica da fase s) e 1210oC (para menor fração volumétrica da fase s) por 2h. Foram realizadas caracterizações por meio das técnicas de microscopia óptica e eletrônica, assim como a utilização das técnicas de análise por energia dispersiva de raios-X (EDX) e dispersão de elétrons retroespalhados (EBSD). Os resultados obtidos foram comparados ao estado como recebido do material (bruto de fusão). Verifica-se a presença da fase s em todas as condições, havendo diferença quanto a fração volumétrica em função do tratamento aplicado.

Aug 16, 2017

By Mike Dry, Rod Dry

If humanity is truly serious about reducing emissions of carbon dioxide into the atmosphere, today’s power plants burning fossil fuels will have to be replaced by power plants that do not emit CO₂. Unless carbon capture/sequestration becomes practical, the new power plants will be hydroelectric, wind, solar or nuclear installations. Hydroelectricity requires the appropriate geography. Solar installations can only deliver power as and when sunshine is available, and wind installations when the wind blows. Therefore, power from these sources will be intermittent, but the demand for electricity does not follow the patterns of sun and wind. That will require large-scale electricity storage and/or load following by the remaining power suppliers, increasingly so as the use of fossil fuelled power generation declines. Modern nuclear power plants are designed for demand following. However, operating at lower than design output has a negative impact on the economics of nuclear power plants because the overall cost of the electricity they generate is dominated by capital cost. Primary (blast furnace) iron smelting is responsible for a significant part of global CO₂ emissions because the reagent used is carbon. Were it available in sufficient quantity (and at a low enough cost), hydrogen could replace carbon in the manufacture of raw direct reduced iron (DRI), using technology such as modified HYL (Tenova Hyl, 2018) or Midrex (Ravenscroft, 2017). This paper examines a scenario in which, instead of demand following, nuclear power stations are operated at their design capacities and surplus power is used to generate hydrogen in off-peak periods. This hydrogen is then used to replace carbon in the manufacture of raw steel.

Jan 1, 2020

By Flávio de Castro Dutra

Este artigo apresenta a influência da temperatura e da atmosfera de secagem sobre a resistência mecânica de um aglomerado esférico, com diâmetro entre 3 mm e 8 mm, constituído de pellet feed e silicato de sódio, produzido através de pelotamento em discos e endurecido em temperaturas até 550ºC. O aglomerado obtido a partir deste processo apresenta características que permitem que o mesmo possa ser transportado a longas distâncias e manuseado até a sua utilização na sinterização. As principais técnicas experimentais utilizadas neste estudo foram difração de raios-X, espectroscopia Raman, microscopia eletrônica de varredura e análise térmica. O aglomerado foi submetido à secagem em temperaturas entre 100°C e 550ºC e atmosferas constituídas de ar atmosférico e/ou CO2. Durante o processo de secagem, observou-se a influência da temperatura e da atmosfera sobre a resistência à compressão do aglomerado após exposição à água, assim como na morfologia do silicato de sódio, evidenciando uma dependência entre elas. O uso de CO2 durante a secagem mostrou-se eficiente para a formação de um aglomerado com maior resistência mecânica após exposição à água.

Aug 2, 2018

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By R Cunningham, P Duniam

Late in 2005 it became apparent that cave propagation at the Northparkes Mine was not progressing as planned. By mid-2006 sufficient Reserves were identified to warrant an extensive drill and blast program to assist in cave propagation. This program began late in 2006 and concluded early 2007. A significant challenge faced was the drilling and blasting of holes between 75 - 240 m in length in the South Wedge in Lift 2 at Northparkes Mines E26 orebody. The project set new benchmarks in production drilling and charging in underground metalliferous mining. This paper discusses the drill and blast designs, the challenges and the operational issues encountered with this project. Also highlighted are ways in which these were overcome.

Jan 1, 2007

By Xiao-dong Xiang, Hong-bo Jin, Ming-sheng He, Huo-guo Pang, Can-hua Li

The specification of the steel slag aggregate will be mutated if the ag- gregate is prepared by a single type crusher. The specification stability of the steel slag improved significantly when the jaw crusher and the cone-crusher are com- binedinthecrushingprocess.Thecombinationofthecrusherandscreenisapplied to produce steel slag aggregate while the roller washing process for removing the dustfromthesurfaceofaggregate.Apilotproductionlinehasbeenestablishedby this technology. The specification stability and the road performance indicators of thesteelslagaggregateshavebeengreatlyimprovedbythispilotproductionlineas compared with the traditional production line. The particulate of the steel slag aggregate is decreased by 81% compared to the traditional line. (cid:1) (cid:1)

Mar 1, 2018

By Ricardo Thomé da Cruz

Na produção de aços é essencial garantir maior durabilidade do material refratário em panelas siderúrgicas. A formação de um revestimento protetor (“coating”) de silicato dicálcico (C2S) em tijolos dolomíticos em contato com escórias básicas é fundamental ao aumento da vida útil dos mesmos. As temperaturas solidus e liquidus do C2S alfa puro são de aproximadamente 1.464°C e 2.154°C. Assim sendo, é esperada uma alta fração de sólido nas temperaturas de refino do aço. No entanto, a presença de óxidos como Al2O3, FeO e a fluorita (CaF2) na escória podem acelerar a dissolução do coating pela formação de fases de menor temperatura de fusão. A fim de melhor compreender esse processo, foram preparadas amostras de diferentes composições de fluorita + C2S na temperatura de 1.600°C. Os resultados foram analisados com o auxilio do software FactSage (simulação termodinâmica). Especificamente, foi estudada a influência da formação de fases e da temperatura de formação das mesmas, as quais levam a fusão do coating. Os dados de simulação foram validados através de ensaios em forno de laboratório.

Jul 30, 2018

By Guilherme Rocha Vianna

A proteína mais consumida no mundo é a de pescado e o sistema de produção de peixes em tanque-rede já é consagrado mundialmente, com mais de 150 espécies sendo cultivadas. O Brasil foi o 12° produtor mundial de pescado em 2012 e poderá se tornar o segundo maior produtor até 2024. Isto porque o Brasil possui ótimas condições para a aquicultura: 12% de toda a água doce do mundo, águas de superfície represadas e uma grande disponibilidade de cereais para a formulação de rações. Hoje um dos principais problemas enfrentados é a colmatação, que consiste no fechamento da malha da tela por algas e organismos. O objetivo deste trabalho foi avaliar a integridade de telas de arames para tanques-rede em água doce, buscando um sistema de produção de peixes produtivo. Foram avaliadas telas de arame galvanizado plastificado, galvanizado plastificado com tinta anti-incrustante, arame bezinal e inox 304. Essas telas foram avaliadas em campo na bacia do rio prata por um período de 2 anos e após a sua retirada foram avaliados o peso e o aspecto superficial das telas. Os resultados mostram que as telas de arame bezinal apresentaram a maior integridade.

Aug 16, 2017

By Rosiane Mary Rezende Faleiro

O GMC intensivo, apoiado na evolução da metodologia do GMC atual, é um grupo de trabalho no qual os desempenhos dos processos são analisados e melhorados expressivamente em um curto espaço de tempo. Surgiu na indústria automobilística japonesa e consiste na melhoria contínua dos processos com base no envolvimento das pessoas e o trabalho em pequenos grupos. As principais diferenças estão na velocidade de condução da análise e da implementação das ações, além da maior disponibilidade e dedicação dos integrantes do grupo e do gestor. Foi formado um grupo de 9 pessoas para reduzir a queda de carvão vegetal nas correias transportadoras e em seus entroncamentos, com integrantes da produção e da manutenção. Durante a “semana de execução”, o grupo ficou 100% disponível para planejar e executar ações levantadas para solução dos problemas de queda do carvão vegetal. Após essa semana, o grupo teve mais quatro meses para fechamento e sustentação das ações. O resultado do grupo foi uma redução da queda de carvão vegetal em 49%, para uma meta inicial de 20%, o qual representa cerca de 183t de carvão vegetal por mês.

Aug 1, 2018

By Vitor Falcão Artacho

As ligas de alta entropia são sistemas de ligas multicomponentes onde os elementos constituintes estão em proporções atômicas equivalentes ou quase equivalentes. As ligas de alta entropia são materiais avançados com propriedades únicas e promissores como materiais estruturais. Contrário as fases intermetálicas ordenadas esperadas pela metalurgia clássica, fase simples em solução sólida com estruturas CCC e CFC têm sido encontradas nos sistemas de ligas de alta entropia. O objetivo do presente trabalho foi preparar e caracterizar as ligas selecionadas FeCrNiCoAlCu e FeCrNiCo(AlCu)0,5. A preparação da liga foi realizada em forno a arco voltaico em atmosfera protegida. A caracterização microestrutural foi realizada através de microscopia ótica e microscopia eletrônica de varredura e por difração de raios-X. A caracterização mecânica foi realizada por medidas de dureza Vickers e por ensaio de compressão a frio. Os resultados mostram que ambas as ligas são constituídas por soluções solidas de estrutura dendrítica. A microdureza e o limite de escoamento compressivo da liga FeCrNiCo(AlCu)0,5 foi superior à liga FeCrNiCoAlCu.

Aug 8, 2018

By Gustavo Coqui Barbosa

Neste trabalho, foi desenvolvido um modelo de elementos finitos para simular o primeiro passe da laminação a quente do trem acabador de tiras de aço C-Mn. O comportamento desse aço é definido por equações constitutivas que descrevem os mecanismos de encruamento e recristalização acoplados aos campos de tensões, deformações e temperatura. Foi implementada uma sub-rotina em linguagem FORTRAN disponível no programa de elementos finitos ABAQUS/Standard. O modelo foi estabelecido no estado plano de deformação por meio de elementos finitos com acoplamento dos campos de temperatura e deformação para o cilindro de trabalho e tira. As dimensões e condições de processo foram obtidas a partir de dados industriais do laminador de tiras a quente da CSN. O modelo prevê as distribuições de temperaturas e valor de carga de laminação em boa concordância com as medidas industriais. Os resultados do modelo evidenciam que há ocorrência de recristalização dinâmica durante o primeiro passe e, apontam que em determinadas regiões da tira a fração recristalizada dinamicamente chega a 100%. A análise de sensibilidade dos parâmetros do modelo foi feita para determinar o seu impacto nos resultados das simulações, notadamente na força de laminação e no tamanho de grão austenítico final.

Jul 30, 2018

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Euzébio Bernabé Zanelato

A incorporação de resíduos proveniente de indústrias na construção civil é uma prática cada vez mais comum, pois além de diminuir a quantidade de material descartado no meio ambiente, pode ainda melhorar as propriedades dos materiais empregados na construção civil. A incorporação de resíduos em cerâmica já é realizada com sucesso em incorporações adequadas, inclusive em telhas onde a qualidade exigida pelo produto é superior. Dentre os resíduos com necessidade de destinação encontra-se o resíduo da indústria de papel. O objetivo deste trabalho é avaliar a incorporação do resíduo de papel na fabricação de telhas cerâmicas, foram utilizadas incorporações de 0%, 10%, 20% e 30% para comparação dos resultados. Os materiais utilizados na pesquisa, argila e o resíduo foram caracterizados pelos ensaios de granulometria, análise química e densidade real dos grãos. Para avaliar o melhor teor de incorporação foram confeccionados corpos de prova e realizados os ensaios de resistência à flexão, variação linear e absorção de água. Os resultados indicaram que é viável a utilização da incorporação de 10% de resíduo, apenas por questões econômicas e ambientais, já que as propriedades pouco se alteraram nesta incorporação.

Oct 30, 2017