Search Documents

By Hanns J. Billmayer

This report, which covers the period from June 15, 1974 to May 30, 1975, describes the work performed in compliance with the requirements of Contract No. H0242065 and modifications 1, 2, and 3 thereto. The purpose of the original contract was to equip the second shuttle car in the Jewell Ridge No. 12 mine, section 6R, with a refined design canopy and seats. In addition, several refinements and improvements were to be designed and installed at the same location on the cutter and the loader. However, during October 1974 in response to a request from the Technical Project Officer, the contract was modified to eliminate all of the cutter and loader tasks and substitute the design, fabrication, and installation of an improved canopy on the no. 2 roof drill in the above mentioned section of the Jewell Ridge No. 12 mine.

Jan 1, 1975

By Keith Maki

This paper details a simple substitution of precise electronic timing in the holes for standard pyrotechnic delays. In addition, we wanted to use two electronics in bottom and top to test the colliding shock wave theory. It also discusses the difficult loading conditions on the Iron Range of Northern Minnesota. No preliminary analysis (Signature Hole waveform analysis) was done to determine the most favorable blast timing for fragmentation increase or vibration reduction.

Jan 1, 2007

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

The transition from exploration to feasibility is a stage in the development of mineral resource projects that is frequently not handled well. The transition marks a point in the project development process where resource evaluation priorities change significantly from the discovery of mineralisation and the rapid assessment of the potential tenor of the mineralised system, to the detailed assessment of the deposit.   Information used in the exploration process tends to be of a qualitative or theoretical nature initially, but gradually becomes more quantitative in character as geological knowledge relating to individual prospects grows.   The transition from discovery and rapid exploration of a new deposit occurs at a relatively early stage in project development, coinciding with the first attempt to prepare a resource estimate for the deposit. Fundamental assumptions regarding both structural and grade continuity and uncertainty inherent in existing information need to be made so that they themselves may be addressed during the collection of additional data.   The effective commencement of feasibility studies involve the introduction of new accountabilities either as a result of appointment of a project manager, and through needing to be able to quantify: ò     the quality of data being collected for resource evaluation purposes; ò     confidence associated with resource estimates; and ò     the need to develop an audit trail for the project, required to make the resource evaluation decision-making process as transparent as possible.   Quality assurance is a concept to which exploration geologists have frequently had little exposure. Being able to demonstrate the quality of data used in feasibility studies is, however, a crucial component of the overall risk management and reduction.   Development of a transparent audit trail for data assists in demonstrating the quality of data which is frequently perceived to translate directly to confidence inherent in resource estimates.   Establishing procedures for geological data collection and management also provides a more reliable framework for making decisions that impact on project execution, again resulting in improved confidence in resource estimates and associated geoscientific data.   Regular, independent technical audits, in principle similar to audits conducted for the ongoing certification of standards compliant quality assurance systems, are a major, positive factor in effective project management and execution.   Information used in project evaluation, feasibility and development must be based on facts. Facts are effectively observations that are ideally made systematically, recorded in a systematic manner, and by being collected effectively are not subject to change.   Effectively managing the transition from exploration to resource evaluation, feasibility and project development involves recognising the nature of changes in the nature, detail and scope of geoscientific data required at each stage of project development. In doing so it is essential to: ò     recognise when the change occurs (as early as preparation of the initial resource estimate for a project); ò     accept that the change may not be gradual; and, ò     ensure that the project evaluation team is adequately resourced.   These objectives require recognition of the value of previous experience and the need to instill a true team approach amongst both staff and contractors associated with the project. Regular formal and informal communications between staff, contractors and other stakeholders in the project are an essential tool in ensuring personnel are aware of factors affecting their role in the project.

Jan 1, 2004

By Xinhua Wang, Qiangqiang Wang, Yubin Li, Shusen Li, Lifeng Zhang

"Numerical simulation on the fluid flow in a Flow-Control Mold (FC-Mold) were performed. The motion of inclusions were calculated. With FC-Mold, the flow pattern and surface velocity become more symmetrical, and at higher casting speed the velocity of liquid steel in the top region of the mold was largely reduced with the highest velocity of the meniscus reducing from 0.65 mis to 0.4 mis, and the meniscus shape became flatter. With FC-Mold, more inclusions approached to the surface of the slab and the amount of inclusion in the center of mold became fewer. Larger inclusions were easier to remove, however, the EM filed of the FC-Mold could hardly improve the removal of inclusions from the molten steel.IntroductionElectromagnetic brake technology is an effective method to control the flow pattern within continuous casting mold, together with other casting parameters, nozzle design and mold geometry [1-5]. Due to the interaction between the applied magnetic flux and the conductive molten steel inside the mold cavity, a force is generated in the direction opposite to the jet flow, which can decelerate the high speed steel jet from the SEN ports. The potential benefits include fewer surface and internal defects, fewer inclusion especially at higher casting speed. However if used imperfectly, electromagnetic forces can have opposite effect [6]. Numerical models are the best tool to optimize electromagnetic flow control. In the current study, numerical simulation was performed to investigate the flow field in a continuous casting FC-Mold, and the effect of different operation parameters on the flow, surface level and velocity in FC-Mold were discussed."

Jan 1, 2013

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By Forrest T. Moyer, Nina L. Jones, Mary B. McNair, Virginia C. Berté

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bueau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings:

Aug 1, 1965

By Denise de La Corte Bacci

The Brazilian Regulation NBR 9653 is a guide intended to evaluate mine and quarry blasting effects in urban areas. The first version, written in 1986 by the Committee of the Brazilian Associate of Technical Norms, is currently being revised. Current regulations specify a maximum PPV limit of 15 mm/s (0.59 in/s) without consideration of frequency or type of structures being protected. The present regulation is still a draft and it is not validated. Several different agencies and institutions have participated in the Committee such as the Environmental Agency from the State of São Paulo (CETESB), University of São Paulo (POLI-USP), University of Rio Grande do Sul (UFRGS), National Department of Mineral Resources (DNPM), Aggregate Industry (ANEPAC and SINDIPEDRAS), besides a number of industry representatives, explosives manufactures and independent consultants. The present regulation proposes to modify the limits of particle velocity and introduces new definitions and criteria for evaluation of vibrations, as well recommendations to address blast vibration complaints.

Jan 1, 2005

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By B. S. Pierce

The National Coal Resource Assessment – 2000 project was a multi-year effort by the U.S. Geological Survey to identify, characterize, and assess the coal resources that will supply a major part of the Nation’s energy needs during the 21st century. The purpose of the USGS National Coal Resource Assessment (NCRA) was to (1) digitally assess selected coal beds and zones that will be the most important in the next few decades, (2) create publically available stratigraphic, geochemical, and geographic information system (GIS) databases to answer a variety of questions of importance to government, industry and public decision makers, and (3) provide interpretive geologic and geochemical information for the primary coal resources of the Nation. Five priority regions were assessed: the Appalachian Basin, Illinois Basin, Gulf Coast, Illinois Basin, and Northern Rocky Mountains and Great Plains. The NCRA was a cooperative effort between the USGS and a number of State geological surveys in these coal-bearing regions. A study of coal resources on Federal lands was also conducted. Adequate energy supplies and the efficient use of those supplies are critical to the economic well being of a country. Affordable and reliable coal supplies are essential to the interests of our national and local policymakers. Policy makers require a range of information on the energy supply, as well as the economic and environmental issues associated with that energy source and its use. Formulation of an effective national energy policy and development of energy resources requires that we understand the geology, distribution, quality, and size of the national energy endowment.

Jan 1, 2001

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

The hoisting system at the Newcrest Telfer mine is designed for a final duty of 7.35 million tonnes per annum at a hoisting distance of 1450 m. In terms of hoisting capacity (t/h) times hoisting distance it is one of the largest friction hoist installations. Initially, the hoist will be equipped for hoisting 6.5 Mtpa from 1100 m depth. This new drive technology is now well proven by ABB for mine hoist applications with the first installation in commercial operation since July 2001. To date 17 systems for medium voltage drives and another five for low voltage drives have been purchased from ABB for mine hoists. This paper will also deal with skip design and powerful data loggers with diagnostics for local and remote monitoring that are installed in the Telfer mine hoist.

Jan 1, 2005

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By Ximeng Zhu

In the transpassive region, about 0.4 to 0.8 V (SCE), aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The growth kinetics of the reaction product film, resulting from transpassive oxidation of pyrite were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The effect of electrode rotation speed, solution pH and temperature were examined. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. Activation energies of 66.17 kJ/mole (15.83 kcal/mole) and 38.67 kJ/mole (9.25 kcal/mole) were obtained for associated parabolic and linear rate constants respectively, at an applied potential of 0.6 V.

Jan 1, 1993

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) ammines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Nov 1, 2011

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999