Search Documents

By R. G. Darmody

Longwall coal mining in southern Illinois occurs beneath some of the best agricultural land in the U.S. This region is characterized by highly productive, nearly level, and somewhat poorly drained soils. Subsidence from longwall mining causes changes in surface topography which alters surface and subsurface hydrology. These changes can adversely affect agricultural land by creating wet or ponded areas that can be deleterious to crop production. While most subsided areas show little impact from subsidence, some areas experience total crop failure. Coal companies are required by law to mitigate subsidence damage to cropland. The objective of this study was to test the effectiveness of mitigation in restoring grain yields to their pre-mined levels. The research was conducted on sites selected to represent conventional mitigation techniques on the predominate soils in the area. Corn (Zea mays L.) and soybean [Glycine max.(L.) Merr] yields in 1988, 1989, 1990, and 1991 from mitigated areas were compared to yields from nearby undisturbed areas. There was no significant (a=0.05) difference in soybean yields averaged over the four years. Average corn yields, however, were significantly lower than reference areas. The impact of subsidence and mitigation is variable and site specific. Results were also related to weather. In wet years, yields in mitigated areas tended to be depressed. This research demonstrated that mitigation of subsidence damage can be successful.

Jan 1, 1986

By Renzon Daniel Cosme Pecho

O consumo do carvão mineral no mundo se encontra em aumento nos últimos anos, devido ao aumento dos preços dos combustíveis fósseis. No caso do Brasil, o carvão mineral é de baixa qualidade contendo, por exemplo, elevado teor de cinzas. Desta forma, o beneficiamento do carvão mineral gera uma quantidade grande de rejeito (RJ) que em contato com a água da chuva é responsável pela conhecida formação da drenagem acido. Alguns trabalhos vêm sendo propostos para contornar este inconveniente, alguns voltados para o aproveitamento do enxofre contido, outros pensando na geração de um possível condicionador de solos ou ainda na obtenção de absorventes para tratamento de efluentes. Dentro deste contexto, o presente trabalho estuda uma possível utilização do rejeito de carvão mineral do sul de Brasil através da extração de Ácido Húmico (AH) e a subsequente utilização deste no tratamento de efluentes. O trabalho reporta o uso da eletrooxidação do RJ seguido da caracterização do AH obtido por analise elementar e espectroscopia de 13C RMN CP/MAS. A etapa de aplicação do AH foi conduzida através de uma avaliação sobre a remoção de Pb+2 contido em uma solução sintética. A extração do AH consumiu cerca dos 12% da massa do RJ e a sua caracterização indicou um componente aromático de 54%, seguido pelos grupos alifáticos (34%). A proporção de grupos contendo oxigênio foi relativamente da ordem de 6% de O-alquilo, 3% de COO- e 3% de C=O.

Aug 8, 2018

By Gary Raymond

The Similkameen Division of Newmont Mines Limited operates a low-grade open-pit copper mine in southern British Columbia. The copper mineralization is extremely erratic.As a result, over seven years of operation, ore control methods have evolved from standard flagging based on blast-hole assays, through an in-pit grab sampling system, to the present method of mining to computer-determined ore-waste boundaries based on geostatistics. These improved ore control methods have resulted in a gain of at least 25% on ore tonnage miffed, at the same grade as obtained using earlier techniques. At the same time, geostatistical ore reserve estimates are now within 7% of milled ore tonnage and grade on a yearly basis, whereas the original polygon ore reserves under-estimated mineable ore tonnage by 15% to 45% and over-estimated grade by about 20%. The author discusses why traditional ore estimation methods give poor results in erratically mineralized orebodies and describes the geostatistical approach to the problem.

Jan 1, 1979

By M. A. Bérubé, M. Choquette, P. W. Godbehere

"RESUMELa scorie produite par le procédé pyrométallurgique d'extraction Noranda contient environ5% de cuivre. Elle est traitée comme un minerai conventionnel de cuivre au concentrateur de Mines Noranda et les rejets de flottation présentent encore des teneurs souvent supérieures à 0.3% en cuivre. La scorie est principalement constituée de magnétite, de fayalite et d'un verre siliceux. Bien sûr, Ie cuivre y est majoritairement sous forme de sulfures et d'un peu de cuivre métallique. Le verre contient toutefois un peu de cuivre en solution, de 0.14 à 0.33% en moyenne, selon l’echantillon examine, ce qui représente à peine 1% de tout Ie cuivre de la scorie. Dans les rejets de flottation, cela justifie par contre de 15 à 25% des pertes totales en cuivre, Ie reste se retrouvant sous forme de tres petits globules de sulfures de cuivre ou de cuivre métallique, en moyenne de 2 à 3 micromètres de diamètre et bien emprisonnes dans Ie verre.SUMMARYThe slag produced by the Noranda continuous smelting process usually contains about 5% copper. It is processed as a conventional copper ore at the concentrator of Noranda Mines. The flotation tailings still often contain more than 0.3% Cu. The slag is mainly constituted by magnetite, fayalite and a siliceous glass. Evidently, the copper occurs mostly as sulphides and, to a lesser extent, as metallic copper. However the glass contains a small amount of this metal in solution, between 0.14 and 0.33% on an average, depending upon the investigated sample. This represents scarcely 1% of the total copper in the crude slag, but as much as 15 to 25% of this metal in the flotation tailings, in which the major part of the copper occurs as very small globules of copper sulphides or metallic copper with an average diameter of about 2 to 3 um and well-locked in the glass."

Jan 1, 1987

By Jarinson Ribeiro Rodrigues

Os aços resistentes à abrasão da classe 450 HB foram desenvolvidos para operações em ambientes onde ocorre desgaste excessivo, sendo estes aços martensiticos de elevada dureza e uma difícil soldabilidade. Este trabalho propôs-se a otimizar os parâmetros de soldagem do processo FCAW (Flux Cored Arc Welding) através da análise do projeto de experimentos (Design of Experiments - DOE) utilizando a Metodologia de Superfície de Resposta (Response Surface Methodology – RSM). Após a determinação dos parâmetros de soldagem ideais, foi realizado a caracterização mecânica e metalúrgica de uma junta soldada com estes parâmetros a fim de certificar-se das propriedades da junta com parâmetros de soldagem otimizados.

Aug 16, 2017

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By Renato Pereira da Silva Junior

Soluções poliméricas são uma alternativa para meio de resfriamento com coeficientes de extração de calor intermediários ao da água e do óleo. Pode resultar em uma severidade menor em relação à tempera em água e uma menor emissão de poluentes, maior penetração da tempera e maior segurança em relação à tempera em óleo. O objetivo deste trabalho é analisar a influência da solução aquosa com 0,03% de Álcool Polivinílico (PVA) como meio de resfriamento para o aço carbono SAE 1045, comparando-se os resultados de microestrutura e dureza do aço SAE 1045 como recebido e após tratamento térmico de têmpera nos meios de resfriamento: água, óleo e salmoura.

Aug 17, 2017

By Samuel Soares Queiroz

O presente trabalho realiza um estudo das propriedades mecânicas de metais de solda de alta resistência obtidos pelo processo de soldagem GMAW com diferentes condições de soldagem. Foram soldadas juntas multipasses pelo processo GMAW, com preaquecimento de 150°C e 250°C, corrente contínua, posição plana e aporte térmico médio de 1,4kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal de solda depositado, tanto na condição de como soldado quanto após tratamento térmico a 600°C por 1 hora. Os resultados mostraram que a tenacidade ao impacto experimentou uma redução substancial após o tratamento térmico.

Aug 17, 2017

By Enir da Silva Fonseca

Este trabalho tem como objetivo principal analisar os dados obtidos através dos ensaios a flexão em 40 corpos de provas cerâmicos preparados de acordo com a NBR 13818:1997 e aplicar uma probabilidade estatística para cálculo da resistência à fratura. O modulo de resistência à flexão para a ruptura de cada corpo de prova foi calculado de acordo com a fórmula apresentada no anexo C da norma citada, e aplicada posteriormente no lote à estatística para distribuição de Weibull. Os resultados obtidos não apresentaram uma variação significativa na resistência mecânica à flexão para os corpos de provas sem umidade em relação aos submetidos à imersão em água.

Aug 16, 2017

By Bart Blanpain, Muxing Guo, Bin Yang, Fei Wang

An experimental investigation of the precipitation behavior of the Dy2O3 containing slag during cooling was carried out in this work. The slag with composition 45 wt% SiO2—49 wt% CaO—6 wt% Dy2O3 was equilibrated at 1673, 1773 and 1873 K for 24 h in an argon atmosphere, and then quenched in water to determine the phase relations. The composition and microstructure of the equilibrated phases of the systems were determined by EPMA/WDS. The precipitation behavior of the REEs containing phases during cooling was studied by using an in-situ confocal scanning laser microscope (CLSM) observation technique combined with an infrared imaging furnace heating (IIF). Data resulting from this work aims to support further investigation on separation of rare earths from metallurgical slags.

Mar 1, 2018

By I Lumsdaine

QNI Pty Ltd operates the Yabulu Refinery located 25 kilometres north of Townsville, North Queensland. The plant treats nickel laterite ores sourced from the Philippines, Indonesia and New Caledonia. The cobalt head grade and overall recovery expectations for the 2001/2002 financial year are 0.161 per cent and 53.8 per cent respectively. Cobalt is a valuable byproduct derived from the nickel refining operation which utilises the Caron Process. Any increases in cobalt recovery that are achieved from the existing relatively low level provide significant improvements to the bottom line of the operation. Towards the end of 2000, a project was undertaken to characterise cobalt losses with the sole purpose of improving cobalt recoveries using a variety of analysis techniques. The Time-of- Flight Secondary Ion Mass Spectrometry (TOF-SIMS û University of South Australia) method was used to verify the presence of surface bearing cobalt species, originating from either co-precipitation or adsorption mechanisms. Cross-section examinations were also performed using Scanning Electron Micrscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDXS). These techniques indicated the presence of high cobalt concentrations (in the order of several per cent) within a select number of roasted and leached ore particles. The phenomenon of cobalt losses due to incomplete leaching within specific ore particles was not widely documented within the Refinery prior to these studies. In order to quantify losses via this mechanism, Mineral Liberation Analysis (MLA û JKTech Centre) was also performed on key samples. This paper serves to document a systematic approach in determining the source of significant valuable mineral losses in an established, operating plant. It discusses the use of a variety of analytical techniques, which have been adapted for the minerals processing industry, but are strongly relevant for plant investigations in the hydrometallurgical industry.

Jan 1, 2002

By S. Jeon, T. H. Kim

"Understanding the frictional properties of discontinuities is crucial to ensure the stability of underground structures. In particular, the frictional behavior at depth depends on the complex interaction among mechanical, hydrological, thermal and chemical characteristics and their coupled effects. In this study, a series of triaxial compression tests were carried out to investigate the behavior of rough shear surface of synthetic rocks. The frictional behavior showed little variation at different confining and water pressures. The test results were analyzed using Coulomb’s failure criterion. In addition, numerical analysis was carried out using PFC2D to simulate the test.INTRODUCTIONUnderstanding coupled behavior of rock at depth is of great importance in design, construction and operation of underground structures such as a disposal facility of radioactive waste, hot dry rock geothermal system and oil reservoir. In particular, many uncertainties are involved in characterizing deep rock mass deformation in the designing process and interactions among fluid flow of groundwater, high temperature and stress disturbance should be considered. Many independent studies have been carried out to investigate the thermal, hydro, mechanical and chemical coupled effects in numerical and experimental methods. They include the researches by Lockner, Summers, Moore and Byerlee (1982), Jafari, Amini Hosseini, Pellet, Boulon and Buzzi (2003), Tembe, Lockner and Wong (2010), Lee, Lee and Jeon (2012), Indraratna, Premadasa, Brown, Gens and Heitor (2014)."

Jan 1, 2015

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

By Herbert Clark Hoover, Lou Henry Hoover

DIGGING of veins I have written of, and the timbering of shafts, tunnels, drifts, and other excavations, and the art of surveying. I will now speak first of all, of the iron tools with which veins and rocks are broken, then of the buckets into which the lumps of earth, rock, metal, and other excavated materials are thrown, in order that they may be drawn, conveyed, or carried out. Also, I will speak of the water vessels and drains, then of the machines of different kinds,1 and lastly of the maladies of miners. And while all these matters are being described accurately, many methods of work will be explained. There are certain iron tools which the miners designate by names of their own, and besides these, there are wedges, iron blocks, iron plates, hammers, crowbars, pikes, picks, hoes, and shovels. Of those which are especially referred to as " iron tools " there are four varieties, which are different from one another in length or thickness, but not in shape, for the upper end of all of them is broad and square, so that it can be struck by the

Jan 1, 1950

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

By P. Bhakta

The U.S. Bureau of Mines developed an alkaline oxidative pretreatment leaching procedure to increase the recovery of gold from arsenopyrite (FeAsS) ores. The best solution compositions for arsenopyrite dissolution were determined using cyclic voltammetry and chronocoulometry. Initial arsenopyrite dissolution occurred at -0.20 V versus standard hydrogen electrode (SHE) in a sodium hydroxide (Na0H) solution. Leaching of a high-grade arsenopyritic ore containing, in percent, 28.2 As, 25.3 Fe, 19.9 total S, and 1.0 Sb and, in troy ounces per short ton, 1.6 Au and 5.5 Ag resulted in >90 pct As extraction at 1000 C, 40 psig O2,4 h, and 2M NaOH solution in a 2-L autoclave. Cyanidation of the leach residues resulted in 90 to 93 pct Au and 60 to 80 pct Ag extractions, compared with only 5 and 15 pct, respectively, without the pretreatment. The procedure was further tested by leaching a low-grade gold ore and a bulk sulfide flotation concentrate prepared from it. Cyanidation of the leach residues resulted in 70 pct Au and 31 pct Ag extraction. The NaOH leachate was partially regenerated by precipitating the arsenate as calcium arsenate [Ca3As04)2] and the sulfate as barium sulfate (BaS04).

Jan 1, 1989

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962