Search Documents

Jan 1, 1968

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

By Y. V. Swamy, B. Bhoi, H. S. Ray

Low-grade manganese ores with low Mn/Fe ratios can he enriched through selective carbon reduction of iron oxide to magnetite followed by magnetic separation o f the magnetite. Thermogravimetric analysis (TGA) was used to assess the preferential isothermal reduction of pure M1702 and Fe2O3 using solid carbon. This was followed by reduction of a synthetic analogue of composition comparable to an actual low-grade ore (i.e., Sandur manganese ore, Sandur, India). The carbothermic reduction of the manganese ore converts the hematite and goethite minerals to magnetite (Fe3O4), with the magnetite then going into the magnetic, fraction. The resultant nonmagnetic ,fraction becomes depleted of iron with an enhanced manganese content. These results show that it is possible to reduce the iron from 22% to 5.85%, thus increasing the Mn/Fe ratio from 1.52 to 6.2 with a manganese recovery of about 50%. The recovery was, further improved by grinding the magnetic fraction to -75 µm.

Jan 1, 1999

By William Campbell

FiRst I must express my deep appreciation for the honor of being privileged to give the Howe Memorial Lecture this year and at the same time my feeling of inadequacy to do justice to the subject. The first Howe lecturer was most fittingly, Professor Sauveur, his contemporary and friend, and the subject was beta iron. Last year the second Howe lecture was delivered by Dr. Mathews, one of his most distinguished pupils, who spoke on austenite. This year, the Howe Professor of Metallurgy was chosen to deliver the third annual lecture, and the subject ought to be martensite. No one but Professor Sauveur could have brought to life what was considered by many to have been dead and buried, and he so persuasively and convincingly proved to us by his experiments the existence of something that the followers of that new cult "X-Ray and Crystal Structure " would have us believe is simply alpha iron. And Dr. Mathews from his wide practical experience was so easily able to convince us that austenite was not only the most wonderful of the iron-carbon series, but that it was the wonder alloy of the future. If I were to follow in the footsteps of my distinguished predecessors, I would talk to you about martensite. But when I had planned this lecture, I found that I was writing about Professor Howe and his work and his influence on the science of metals of today, and that martensite had become the secondary theme. And when finally I was obliged to choose a title, I remembered that it was in 1901 I came from Roberts-Austen with a letter of introduction to his very dear friend, Henry Marion Howe, at the Columbia School of Mines, to continue my work at the next bench to Dr. Mathews. Since then a quarter of a century has gone by, and during that time all branches of science seem to have been remade, so great has been our advancement in knowledge and discovery. And now that Metallography has finally established its place as an important branch of science, with its own textbooks and literature, I would like to review what seem to me to be the most important advances we have made in the last 25 years. To do this, I would start with Howe's "Iron, Steel and Other Alloys," and end with Jeffries and Archer's " Science of Metals." In the preface of the former, Professor Howe wrote: My warmest thanks are due to the friends who have aided me with their counsel and knowledge. In particular, let me thank most sincerely Prof. Margaret E. Maltby

Jan 1, 1926

By D. W. Richardson

This Bureau of Mines publication provides the enthalpy of formation of malachite [Cua(COs)(OH)2] as determined by hydrochloric acid solution calorimetry. At 298.15 K the enthalpy of formation from the component oxides is -15.l0±0.30 kcal/mole and from the elements, -251.9±0.5 kcal/mole.

Jan 1, 1974

By Heather N. Dougherty

In the absence of values for each influencing parameter and a known relationship of input-output space, novel approaches should be implemented as proxy solutions to mathematically complicated problems. Proxy solutions can be in the form of linear or non-linear multiple regression equations. Predicting the performance of gob gas ventholes is one of these mathematically complicated problems as it is difficult to know the exact relationships between various parameters influencing gob gas venthole (GGV) performance from active and sealed (completed) longwall panels. In this paper, a discussion of the NIOSH-developed software suite for methane control and prediction (MCP) based on an artificial neural network (ANN) is presented. The application of the ANN-based software suite to develop algebraic relationships for gob gas venthole performance prediction in sealed and active longwall panels is sought. Output information obtained from the NIOSH-MCP software as a response to various input parameters were used to create an input-output database for total flow and methane percentage from GGVs operating in active mines during completed and sealed panel situations. Due to the multi-variable nature of the software, outputs generated using the software for various inputs were used to develop analytical equations first using linear and then second using non-linear multivariable regression techniques. The advantage of this method is its ability to better understand the significant parameters of the relationships between the inputs and outputs for gob gas venthole production in active and sealed panels and to be able to predict their performances using relatively simple analytical functions.

Jan 1, 2010

By Regis Antonio Albertassi Tavares

O presente trabalho propôs-se avaliar a potencialidade de obtenção de uma microestrutura dual phase em um aço baixo carbono com microadição de molibdênio e nióbio, laminado a frio Full Hard. Os estudos foram suportados pelas análises da recristalização da ferrita, da fração volumétrica de austenita formada e sua evolução composicional/estrutural em função da temperatura de encharque no intervalo do campo intercrítico durante o encharque no tratamento térmico proposto com resfriamento em salmoura – a fim de simular o encharque no recozimento contínuo. As caracterizações microestruturais e mecânicas foram avaliadas por Microscopia Ótica, Microscopia Eletrônica de Varredura (MEV), Dilatometria e ensaios de dureza Vickers, e confrontadas com estudos prévios via Espectroscopia de Raios-X de Dispersão de Energia (EDS).

Aug 7, 2018

By Julio Aníbal Morales Pereira

Sabe-se dos problemas associados com as inclusões não metálicas, os quais afetam não somente a operação de fabricação, como também a qualidade do produto final. Por esses motivos, muitos estudos têm sido realizados para melhorar o controle do tamanho, quantidade, forma, distribuição e composição das inclusões. Especificamente para as inclusões de espinélio MgO·Al2O3, ainda é preciso melhorar o entendimento dos fenômenos sobre a formação e modificação destas inclusões para um melhor controle ao longo do processo de fabricação do aço e obter maior limpidez inclusionária nos aços. Assim, neste trabalho, foram revisados tópicos reportados na literatura relacionados com: a formação, influência da composição da escória e modificação com cálcio das inclusões de espinélio.

Aug 16, 2017

By Edir Neves Teixeira

O presente trabalho teve como objetivo o estudo para otimização de distintas condições de tratamentos térmicos de solubilização e envelhecimento em liga forjada de NiTi rica em Ni visando características e propriedades adequadas para aplicações superelásticas. As características microestruturais e composicionais foram avaliadas por Difração de Raio-X (DRX), por Microscopia Eletrônica de Varredura (MEV) associada à Difração de Elétrons Retroespalhados (EBSD) e ao Espectrômetro de Energia Dispersiva de Raio-X (EDX), e correlacionadas com as medidas de dureza Vickers. Baseados em resultados da literatura, apresentou características mais promissoras para tratamentos de solubilização a 950ºC por 120 minutos conjugado com envelhecimento a 350ºC por 30 minutos, ambos com resfriamento em água.

Aug 8, 2018

By Rafael Wilson Soares Ladeira

Realizar manutenções preditivas de forma cada vez mais assertiva é um dos benefícios da atual evolução dos sistemas produtivos industriais conhecida como Indústria 4.0. A Sotreq - revendedora Caterpillar - oferece um serviço de análise de fluidos a partir da coleta periódica para máquinas operantes em campo. Com os resultados das medições, especialistas atribuem às amostras um nível de criticidade, justificativas e recomendações. Neste trabalho propõe-se uma solução que aumentou a eficiência desse processo através da utilização de modelos de Machine Learning treinados com as análises já realizadas que automatizam a classificação e a geração do texto de diagnóstico para novas amostras. As predições do sistema foram consideradas bem sucedidas, com métricas de sensibilidade e especificidade acima de 88%.

Oct 30, 2017

By C. Ketata, M. C. Rockwell

During the operation of a mineral processing plant, the unit processes are investigated by analyzing the data extracted by means of stream sampling. The data structure is identical to the time series form. Data analysis is a crucial step in understanding the plant performance. To control the plant performance efficiently, it is very important to avoid sampling errors, which is impossible. However, it is possible to minimize these errors. The factors influencing these errors are divided into two categories: material properties illustrating its heterogeneity, and sampler features. The purpose of this paper is to study the influence of the material composition variation on sampling errors, and to compare our evaluation method with that of Gy. Note that the stream mass flowrate is assumed to be constant during the sampling process.

Jan 1, 2001

By Matheus Fortes Stiborski

Este estudo descreve a aplicação de três métodos de cálculos teóricos pelos modelos matemáticos de Tafel e Sedlaczek, Siebel e Köster, com o objetivo de calcular o alargamento na laminação a quente de barras em aço AISI 1020 em um laminador tipo duo e definir quais dos modelos de alargamento se aproxima mais dos resultados obtidos experimentalmente. Foram utilizadas amostras com dimensões iniciais de largura (bo), 37,7 mm, altura (ho), 15,7 mm, e comprimento (lo), 300,00 mm onde se ajustou a luz dos cilindros para que fossem obtidas reduções aproximadas de 15% e 20% em altura. Os resultados obtidos indicam que o modelo de Siebel apresenta melhores resultados comparado com os valores experimentais.

Aug 16, 2017

By Cristovão Nery Giacomin

Foi desenvolvido um software para cálculo do balanço térmico dos fornos de reaquecimento de placas da Usiminas em Ipatinga. Ele realiza a busca automática de dados operacionais e das placas reaquecidas, valida, trata os dados e realiza os cálculos das parcelas de entrada e saída dos aportes térmicos para cada forno. Além disso, são calculados o rendimento, a eficiência térmica e o índice de ocupação dos fornos. O desenvolvimento foi realizado em ambientes visuais, com utilização de interfaces gráficas para fácil interação dos usuários com o software. A validação do software foi realizada pela comparação de resultados obtidos na busca automática com valores reais operacionais de balanços térmicos já realizados nos fornos.

Oct 30, 2017

By Frederick C. Trutt

Research performed on arcing faults and their interactions with electrical insulating materials within coal-mine power system enclosures are described. This work was performed at The Pennsylvania State University from December 1, 1976 through August 31, 1978. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of arc and tracking models so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when a fault interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support and maintain an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation. During the course of this research, consideration has been given to the possible effects? of an internal methane-air explosion within an enclosure as well as the potential influence of utilization-voltage-level, conductor spacings, and enclosure venting. Conclusions and recommendations address potential means for protection against enclosure failure, internal design considerations, and low-power testing procedures which might be used to evaluate insulating materials to be utilized within an enclosure.

Jan 1, 1978

By Cristiano da Silva

Este trabalho avalia o processamento por moagem de alta energia bola em TiB2 no efeito da inoculação de alumínio puro. O pó TiB2 comercial foi processado no moinho de alta energia do tipo SPEX e misturado com alumínio em pó de alta pureza. A mistura foi conformada em pastilhas e sinterizadas em atmosfera inerte. As pastilhas foram introduzidas em alumínio puro fundido em teores de 0,15 e 0,30% em peso de TiB2 e solidificado por resfriamento natural. A análise macrografica mostrou um grande aumento no refino de grão por inoculação com TiB2 processado do que em comparação com o material como recebido.

Aug 8, 2018

By Rafael de Andrade Silva

O presente trabalho teve como principal objetivo estudar a evolução da recristalização em chapa de zinco, e para tal objetivo, chapas finas de zinco laminadas a quente foram sobrepostas e processadas pela técnica de deformação plástica severa conhecida como NECAE (Non Equal Channel Angular Extrusion). Em seguida, as amostras foram submetidas a um tratamento térmico de recozimento para recristalização com diferentes temperaturas e tempos de encharque. Para tal objetivo, foram utilizadas análises de microscopia óptica e dureza Vickers. De acordo com os resultados obtidos, observou-se que após o processamento via NECAE houve uma pequena fração recristalizada, e esta aumentou de acordo com o aumento do tempo e da temperatura de tratamento térmico.

Aug 16, 2017

By Ramon Silveira Assis Barros

Este trabalho foi realizado com o objetivo de se investigar o comportamento do aço inoxidável duplex UNS S32304 em meios contendo íons cloreto. Para tanto, foram realizados ensaios CST com carga e deformação constantes usando meios com concentrações distintas de cloreto de magnésio (MgCl2), em ebulição. Foram realizados também análises química, metalográfica e eletroquímica do material. Após os ensaios de CST, foi constatada a suscetibilidade à CST deste material, além da influência da concentração de íons cloreto na solução. Essa constatação foi reforçada após a análise microfractográfica dos corpos de prova ensaiados. A análise eletroquímica do material revelou a evolução de pites em potencial de, aproximadamente, 400mVECS.

Jan 16, 2018

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970