Search Documents

By E. Steiakakis, A. Athousaki

Nowadays, stakeholders have a strong say to the enforcement of best practices by mining and quarrying companies. In most cases there is a direct relationship between sustainable development principles and best practices. Mining companies try to apply best practices in order to sustain their operation without lost time and effort to litigation, and other obstacles. However, when and where there is a lack of state or regional mineral policy, or when the mineral policy is fragmented and touching on conflicting laws, mining operations may be subject to additional administrative hassles, and, thus, operators feel threatened and tend to apply best practices loosely. This paper argues that the only way that mining and minerals operations can be a source of development is to ensure that they are working within the framework of sustainable development. Furthermore, in order to follow the paradigm of sustainable development they would need to be guided by a regional, national or even transnational (i.e. European) minerals policy.

Jan 1, 2011

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009

By T. Kessler

Spark-source mass spectrometry has been used to determine the amounts of minor and trace elements in coal particles of various sizes, including the respirable range (<5 microns). Fifty-six elements ranging in concentration from 0.1 ppm wt to 5,000 ppm wt have been determined. The investigation of coal and coal ash has shown that the organic material in coal does not interfere with the spark-source determination of the various elements.

Jan 1, 1971

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By G. Kordosky, A. Feather, M. Virnig, P. Crane

Introduction The post World War II nuclear arms race and interest in nuclear power generation resulted in a significant demand for uranium in the 1950’s. This led to the development of uranium solvent extraction technology and uranium became the first metal to be recovered on a large scale by solvent extraction (SX) (1), interestingly more than 100 years after the extraction of uranium from an acid nitrate solution using diethyl ether was first reported by Peligot.(2) For a variety of reasons discussed elsewhere (3,4) there have been upheavals in the supply demand picture and price for uranium since the 1960’s. (Figure 1) The low price of uranium from the mid 1980’s until 2004 resulted in a depression of new resource exploration and mine development along with uranium mine / mill closures and decommissioning. People with skills in uranium processing could not find suitable employment and many experienced engineers and metallurgists took jobs elsewhere or retired. This resulted in a significant brain drain with respect to uranium processing technology.

Jan 1, 2007

By M. Abdelkhalek, M. Hepworth, D. Tao, B. K. Parekh

Pre-combustion coal cleaning and post-combustion flue gas desulfurization (FGD) using lime or limestone are the primary methods employed to reduce sulfur dioxide (SO2) emission from coal combustion. These processes generate voluminous pyrite and gypsum solid wastes that are usually landfilled, occupying thousands of acres of land and creating serious land and water pollution problems due to the release of acids and toxic substances. An integrated process has been developed for the combined utilization of gypsum and pyrite wastes by converting them into useful products including lime, sulfur, and direct reduced iron (DRI). The process includes four major steps. The first step is to concentrate pyrite from coal preparation tailings using flotation or gravity separation. The second is the thermal decomposition of pyrite into pyrrhotite and sulfur. This is followed by the reduction of pyrrhotite with carbon in the presence of lime to produce iron and calcium sulfide. The fourth step involves the reaction of calcium sulfide with gypsum to produce lime. The chemical reactions involved in the process were studied using thermogravimetric analysis (TGA) and X-ray diffraction (XRD)techniques. Process variables studied included reaction temperature, time, reactant composition, and purity of reactants.

Jan 1, 2000

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,&apos; E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,&apos; E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J&apos; Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

By Edward L. Wilson, Keshavan Nair, Ranbir S. Sandhu

In planning and designing of underground excavations and construction, it is of considerable importance that the stresses and displacements in the rock mass subjected to arbitrary sequences of unloading and loading be within allowable limits. For determination of the stress and displacement fields, the usual approach is to treat the rock as an elastic material and to apply the principles of the theory of elasticity. However, analytic solutions are available only for a limited class of problems of simple geometry and idealized material properties. Nonhomogeneity and anisotropy of material coupled with complex geometrical configuration and initial stress fields that are almost always preexistent in rock masses at great depths, render the problem intractable by analytical methods. Approximate solution techniques using numerical procedures have, therefore, to be resorted to. The finite element method as applied to plane stress analysis was introduced by Clough.1 It has developed into a powerful tool for the analysis of various field problems in structural and continuum mechanics. The method is well documented in the literature2-6 and, therefore, its historical development will not be discussed here. Wilson&apos;s analysis of the plane stress/strain problem has found extensive use in the area of soil and rock mechanics including stresses around underground openings; stresses and displacements in dams, foundations, etc.7-11 In his analysis of the axisymmetric solid,3 Wilson proposed a procedure to allow for certain cases of nonlinear material properties. In this chapter, the develop-

Jan 1, 1972

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By Steven J. Schatzel

Large-scale methane releases in dual salt mines have resulted in ignitions and mine fatalities as recently as 1979. Several past studies have implied that hazardous methane occurrences in U.S. salt domes are distributed neither uniformly nor randomly, but are geologically controlled and potentially predictable. A first step by the Bureau of Mines in addressing the problem of methane in deal salt mines required development of a new test to determine volumes of gases in solid salt samples. This report considers the results achieved when 80 deal salt samples were tested for gas content by dissolution in a controlled atmosphere chamber. Criteria were organized to delineate salt types based on geological occurrence. Outburst samples range from 0.014 to 7.4 cm3 CH4/100 g NaCl, anomalous salt samples from 0.0027 to 2.6 cm3 CH4/100 g NaCl, and normal salts from less than 0.0003 to 0.31 cm3 CH4/100 g NaCl. The presence of higher hydrocarbons was most common in samples containing larger quan¬tities of methane. The presence of higher hydrocarbons appears to be useful in detecting methane hazards where some methane may be lost before gas content testing. An exploratory rotary and/or core drilling program, dissolution testing for gas content, and up-to-date geologic mine napping could allow a mine operator to assess methane hazards in dual salt.

Jan 1, 1984

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

Over the last three decades, the mining industry has been moving towards more underground mechanized mining methods and the number of LHD vehicles utilised has increased. The growth of mechanization and automation has benefited both workers and the mining companies. However, due to the design of the LHD vehicle and the limitations of the operating environment, restrictions to operator visibility are inevitable. The inability of the equipment operator to see clearly (i.e. people, objects or hazards) around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, visibility assessments for existing machines are traditionally completed in the field using a light filament technique. Past researchers have used the light filament technique to collect obscuration zones around the equipment and to produce a 2D chart of this information. The 2D shadow diagrams have proved to be useful in highlighting potential equipment problems and have been performed repeatedly to show the potential of redesigning a part of the LHD for improving visibility. The light filament method involves manually collecting data and requires a level of judgment to be used. As a result the method is susceptible to errors and requires around three hours to complete. The objective of the current research is twofold; firstly to develop a rapid method for field visibility data collection using a laser scanner and secondly to compare results of repeat tests for both light filament and laser scanning methods. A MENSI GS100 laser scanner along with Pointscape and 3Dipsos software has been used to collect visibility information and process the data. The research aims to develop the laser scanner as a technique to rapidly evaluate the visibility profile of an LHD vehicle. Machine design changes can then be assessed quickly using these results.

May 1, 2004

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

By Flavio Begazo, William A. Enrico

"Southern Peru Copper Corporation's Ilo Refinery, the largest in Peru, began operations in 1975 with a production capacity of 165,000 stpy. Southern Peru bought the Refinery from the state owned Minero Peru SA on June 1, 1994.The Refinery processes blister from Southern Peru's I/o Smelter. Blister copper is processed in an anode plant equipped with two 365 st tilting reverberatory furnaces, a 26 mold casting wheel and an anode press machine. Copper is electrorefined in a tank house equipped with 768 commercial cells, 44 stripper cells, and 40 liberator cells, utilizing two electrolyte circuits and a 21,000 Ampere rectifier.During 1989 through 1994 a program for improving productivity was carried out by increasing the number of cells and increasing current density to the total rectifier capacity. As a result, a capacity 215,000 stpy of refined copper, 2 million tr. oz silver and 6,000 tr. oz gold per year was achieved. In 1994 Southern Peru announced plans to increase capacity to 250,000 stpy of cathode with a US$ 18 million investment and a US$ 2 million investment in environmental improvement projects, as part of the purchase agreement with the Peruvian government.This paper outlines the scope of the SPCC lio Refinery modernization and environmental program. It describes the implementation of the Electrolytic Plant expansion based on instaliation of polymer concrete cells, a new rectifier, a new selenium roaster and a Precious Metal Plant upgrades."

Jan 1, 1997