Search Documents

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By Roland Oliver

Detonators or blasting caps are made in several different grades of strength, because some powders require not only a greater, but a different initial detonation than others to convey their maximum energy through a whole charge, and the detonating qualities of each powder vary with changes in its physical condition––whether it be warm or cold, rigid, plastic, homogenous or otherwise.

Jan 1, 2007

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By L. Bloomquist

This paper describes how Automated Mining Systems (AMS) is evolving the state-of-the-art in guidance systems for autonomous underground vehicles. The techniques, trade-offs, and lessons learned from these systems are described, including the safety regime that has been implemented. First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach. The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system. The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology.

Jan 1, 2004

By L. Bloomquist, C. Arnoldi

"This paper describes how Automated Mining Systems (AMS) is evolving the state-of the- art in guidance systems for autonomous underground vehicles. The techniques, tradeoffs, and lessons learned from these systems are described, including the safety regime that has been implemented.First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach.The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system.The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology."

Jan 1, 2004

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005

By R. O. Burt

"Gravity Concentration, the oldest form of Mineral Processing, remains of major importance to the Industry. Current applications of Gravity Concentration are briefly examined.The Paper details one approach to the development of a Gravity Concentration Plant, from laboratory and mineralogical techniques, through Pilot Plant testing, where applicable, to the actual design of the plant.INTRODUCTIONGravity Concentration, once the major method of concentrating minerals has, for much of the twentieth century been regarded, like the dodo bird, as obsolete. However, in more recent years it is enjoying something of a renaissance, and is once again being treated as a useful, economic alternative in the Mineral Processing Engineers' arsenal.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive."

Jan 1, 1984

By Gregorio Llanos Villarreal

Dado que la expansión progresiva de la mina Calera exige una productividad de material detrítico, se ha optado por una alternativa de voladuras a gran escala que controle el desmonte proveniente de los desarrollos de la mina. En esta perspectiva, el presente estudio refiere las experiencias de voladura adquiridas en la mina Calera, a partir de la aplicación de "voladuras de coyote" a gran escala. La eficiencia de sus resultados redujo la utilización de los equipos pesados en la cantera de relleno, así como los costos de los conceptos.

Apr 1, 1991

By S. J. Benson

The Harts Range deposit, owned by Olympia Resources is located some 130 kms northeast of Alice Springs, in central Australia (part of Australia’s Northern Territory). The core economic minerals here are industrial grade garnet and alumino magnesio hornblende (AMH). The resource contains an estimated 2.3 million tonnes of recoverable garnet and 6.2 million tonnes of recoverable AMH, making Harts Range one of the most significant abrasive medium deposits in the world. Part of the general marketing axiom of Olympia Resources is to make high quality products from the garnet and also a special series of blended garnet/AMH products to match the needs for other sectors of industry. The deposit mineralization is of alluvial origin and thus, requires no significant liberation regimes. Over 50% of the head feed is in the form of SiO2/quartz and as much as 17% is –63micron clay slimes and mica. Original pilot scale testwork for flowsheet development centred around fairly conventional wet gravity systems, with spiral concentrators being the pre-eminent separating device. To a point, this type of flowsheet was going to achieve some of the aims albeit fairly predictably. The one area that this circuit would be very limited though is in the recovery of the very coarsest of the medium SG minerals. This was going to be a very important and longer-term costly flaw. Amongst the highest demand, greatest value of products to be produced will be the range of garnet & AMH in the +600 microns sector. A flowsheet dominated by spirals would be fated to forfeit a significant proportion of these coarse minerals to tails. At the Outokumpu Technology P/L test facilities in Perth, testwork was conducted using a pilot scale Floatex® Density Separator, the LPF-230 model. Using a twin stage approach, whereby a primary Floatex® underflow reports directly to a secondary Floatex®, recovery of the economically important +600 micron garnet was increased from 65% in the spirals-only flowsheet to 95% using the Floatex® based flowsheet. Finally, the other significant aspect of this approach is in substantial simplification of the circuit required and a huge reduction in plant footprint. Also, the nature of using hindered settling provides substantial opportunities for process control and automation.

Jan 1, 2005