Search Documents

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

By A P. Tinnelly

This paper explores the structural/physical and policy based issues that have lead to the apparent resource conflict between Forestry and Mining on the West Coast. Both industries are important to the West Coast and bear many similarities, particularly at the corporate end of the mining scale. However there are very distinct structural differences which set the scene for friction at the boundaries. Examples of how mining impacts upon forestry illustrate where some of the friction arises and provides some insight as to where some solutions are or may be found.

Jan 1, 1996

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

By V. Dinesen

"Grinding is simply the function of reducing particles in size or creating new surface areas. This may be accomplished by many means but we will only concern ourselves with the continuous grinding process as performed in a revolving drum or mill, containing a grinding media. Such a mill consists essentially of a feed head, a cylindrical shell section and a discharge head. To prevent internal wear of these parts it is customary to attach replaceable linings over the wear areas. The specification and design of these mill liners is more important than generally conceded. As they reduce the effective internal volume of the mill, they will consequently affect the whole mill ·design and operation.A number of mill designs of various sizes are available for combined crushing and grinding of materials within a wide size range. For simplif1cahon purposes we will refer 1n particular to conditions relating to standard mill shapes having a length which is greater than the diameter. Such mills usually rotate at speeds between 60% to 85% of the critical speed and may, depending on the grinding media used, be classified as rod mills, ball mills and pebble mills.LINER MATERIALSA great variety of materials have been and are being used for mill linings. These include wood, ceramics and cements, rubber and plastic compounds, rolled and forged steels, cast steels and cast irons, both plain, alloyed and specially treated.The choice of a liner material depends on many factors. In both dry and \\.:et grinding, it may be necessary to consider product purity, colour, chemical reaction etc. but for our purpose we \viii refer to wet grinding operations as generally used within the mining industry."

Jan 1, 1972

By R. G. Gifkins

Mean boundary migration depended linearly upon creep extension under various conditions. Prolonged annealing or air-casting increased the proportion of immobile boundaries at a given stage of tests. Grain growth during annealing followed a power law. The linking of migration and sliding in creep and models for migration are examined; activation energies are calculated from these models. Segregation of oxygen to boundaries appears to be a controlling factor. THE idea that boundary migration and boundary sliding during creep are linked has often been suggested,'-5 especially when evidence has been obtained for an alternation between the two processes. In simple bicrystals sliding can occur without any migration6 but in more complex bicrystals7 it is observed. McLean' and Couling and Roberts 5 made measurements of both sliding and migration; McLean concluded that there was no linking of the two processes whereas Couling and Roberts supported the idea. McLean' also developed a model for migration during creep and annealing. The present work was initiated as part of a study of the recrystallization of lead during creep9 but has been extended to examine some aspects of the mechanism of migration. MATERIALS AND METHODS Specially refined high-purity lead* was used; the total of impurities, excluding oxygen, was 0.0008 wt pct. Oxygen was removed as far as possible by melting in vacuo, treating at 550" to 600°C with hydrogen and then casting at 450°C under a vacuum of 10-2 mm Hg; the oxygen was then believed to be 0.00005 wt pct. Specimens were made from extruded strip and then annealed at the required temperature in an air oven, controlled to 5 lac. They were then polished in a mixture of acetic acid and hydrogen peroxide. At this stage some specimens were etched to give grain contrast and their grain sizes determined by the intercept method. Migration of boundaries during creep was measured on the surface of polished (not etched) specimens, directly loaded at room temperature (22°C) or 50°C (52"C) to initial stresses of 300 to 700 1b per sq in. Twenty six vacuum-cast hydrogen-reduced specimens were used and, in addition, two specimens were from material air cast after hydrogen reduction ("partial" air cast) and two from air-cast material not treated with hydrogen ("full" air cast). Duplicates were made in the majority of tests. At intervals through the creep tests, specimens were unloaded and the migration measured, normal to the direction of migration at the point of measurement, for each boundary along standard traverses. Usually between 110 to 180 boundaries were measured at each of some twelve stages of the tests. Migration was measured on the projected image (X100) using prism illumination. Fig. 1 illustrates the method of measurement and shows the kind of variation of migration found from boundary to boundary and along particular boundaries. Fig. 2 gives an example of more extensive migration. The mean value of distance migrated was generally reproducible to *10 pct but occasional points gave a scatter of *20 pct. The correctibn applied by McLean8 to allow for the contribution sliding makes to the apparent distance of migration could not be used, for the sliding at most boundaries was too small to measure with the equipment available. There were two reasons for supposing the correction unnecessary in the present work;

Jan 1, 1960

By J Youngson

Gold placers can be difficult to locate in areas where tectonic activity and paleogeography have changed significantly since placer formation. Existing placer exploration models are useful in areas that have a relatively simple geological history, identifiable relationships with parent sources, or a history of placer mining. However, exploration becomes increasingly difficult in areas where tectonic activity and sedimentary recycling repeatedly redistribute the gold. Gold placers in the Waitaki River catchment, North Otago, New Zealand have no primary source within the catchment. During the Eocene placer gold was transported by a river ('Buster River') that flowed in a northeast direction from Central Otago toward a coastline at Maerewhenua, North Otago. This river and coastal system was inundated by marine transgression during the middle Tertiary. Since the Miocene its placer deposits have been uplifted and eroded and any links with parent sources have been severed. Changes in paleogeography resulted in local reconcentration and local dilution of placer gold in different areas in the Waitaki catchment. Thin veneers of old Waitaki River gravels (Kurow Gravels), containing gold recycled from the older placers, have been deposited unconformably on strath surfaces cut into Tertiary or older rocks. These gravels along with remnant Eocene fluvial and shallow marine strata provide potential placer exploration targets. Uplift and erosion of non-auriferous rocks in the Waitaki catchment to the west and north of the study area has resulted in considerable dilution of potential placer deposits downstream, especially in areas of gravel aggradation. We present a placer exploration model that is founded on answering fundamental questions pertaining to the paleogeography and geological history of the sediments associated with the placers.

Jan 1, 1999

By T. F. Bower, M. C. Flemings

Results are reported of a study of surface dendrilic structure of an Al- Cu alloy solidified against a chill wall. Most primary and secondary "arms " in the surface dendritic structure are arranged orthogonally, giving the impression of strong preferred orientalion on the surface. However, no such preferred orientation exists and it is therefore evident the arms do not represent (100) directions. The primary arms are shown to be interseclions of a (100) plane wilh the chill plane, or, equally often. the projeclion of a (100) direction on the chill plane. Secondary dendrite arms are usually within a few degrees of 90 deg to the primary arm, independent of grain orientalion. Prirary, secondary, and higher-order surface dendrite arms almost always represenl intersections of (100) platzes with the chill surace, or pvojections of (100) direclions. Growlh of secondary arms is favored on the side of the primary arm where a (100) direclion points toward the chill surfAce a1 a Lou, angle. Surface dendrile arms are often observed to be bent. In these cases, the crystal lallice changes orientation; bending is concave to the chill surface. In a previous paper,' a technique was discussed whereby large grains can be obtained at a chill surface. The technique used involves quickly drawing superheated liquid A1-4.5 pct Cu alloy into a thin copper mold, so that the mold is full well before solidification begins. The chill surfaces employed are polished copper blocks coated with amorphous carbon. Shrinkage during solidification between dendrite arms and grains delineates both, without the need for polishing or etching of the cast surface. The grain structure of the chill surface was discussed in a previous paper;' in this paper, the dendrite arms within each grain are examined. Previous work on surface dendrites includes that of Edmunds, who studied the development of preferred orientation in zinc, cadmium, and magnesium.' In zinc and cadmium, he found that the surface region has a (0001) texture (parallel to the chill surface). Walton and Chalmers reasoned that, since the fast growth (1010) directions are in the basal plane, nuclei which have this plane parallel to the mold wall would produce larger grains than nuclei with other orientations. Hence, the texture observed is as expected.3 The same authors, in measurements on aluminum ingots, found no preferred orientation at the mold wall. However, the X-ray technique they used measured the preferred orientation in terms of grain numbers, not grain areas; larger grains were weighted equally with small ones. No preferred orientation is expected on this basis at the chill surface. In a later paper,' Edmunds stated that experiments show a random grain orientation at the surface in die cast aluminum; his technique, also used in his earlier paper, takes account of grain area. Little work has been published on the dendritic structure of metal chill grains. Recent work of Biloni and Chalmers on "predendritic growth" shows the change in morphology from spherical to dendritic during the initial stages of freezing, 5 but this work did not include detailed examination of the fully developed dendrites. Other pertinent work includes that of Lin-denmeyer, who investigated the growth of ice dendrites. 6 When growth was on a substrate, the dendrite axes were bent. The bend corresponded to a change in orientation of the crystal lattice and occurred in such a way as to align the basal plane to the substrate. DENDRITE STRUCTURE Fig. 1 shows the chill surface of a typical casting poured above the critical temperature necessary to produce coarse grains. A cursory examination of these grains shows that the surface dendrite arms within most of the grains are oriented roughly perpendicular to each other. One is tempted to assume that these are (100) directions and that, therefore, marked preferred orientation exists at the chill face. This, however, is not the case. Each of the grains in the casting of Fig. 1 was separately identified, Fig. 2, and its orientation determined by the Laue back-reflect ion method. Results are given in Fig. 3 and it is seen there that no preferred orientation exists. Even when grain area is accounted for, there is no significant preferred orientation. The relationship between surface grain structure and crystal orientation was then obtained by assigning X and Y axes to the casting surface, Fig. 1, and assigning the same axes to the stereographic projections of each grain. Thus, the visible surface structure could be compared readily with grain orientation. This was done for fifty-five of the grains of Fig. 1. Results of this study on three typical grains are described below, and some general observations given subsequently. Fig. 4 shows the structure and stereographic projection of a grain which lies near the (100) zone (with respect to the casting surface). The X and Y directions are marked on the projection, and the photomicrograph mounted with the same orientation. Poles of the stereographic projection represent crys-tallographic directions in the grain which point out of the casting, toward the chill. Two (100) directions are shown in Fig. 4. A line joining the center of the projection and a pole represents the projection of the pole onto the X-Y plane (chill surface). Two such lines are shown in Fig. 4 (solid lines). A line joining the intersection of a great circle with the circumference of the projection gives the trace of a crystallo-graphic plane in the chill surface; two such traces are shown (dashed lines).

Jan 1, 1968

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

Being a geologist I intend describing the renaissance of the gold industry in Australia within its geologic framework; there is a geological pattern to the numerous gold projects which have been brought on stream over the past decade. We are now about midway through our third and largest gold boom which, at a peak of 7.5 million ounces is about twice the production peaks achieved in the preceding booms. From discovery in 1851 through 1870 we saw the first boom largely based on alluvial production in NSW and in Victoria at the great Ballarat and Bendigo Goldfields. The discovery of the Golden Mile in Kalgoorlie, Western Australia, underpinned the second gold boom in the period 1895 - 1915. On that basis the present boom should last through the next decade.   It has been a golden decade for Australian gold production. From less than ten mines in 1980 with production over 10 000 ounces and the largest, Telfer, with output of about 130 000 ounces we now find over 130 deposits being worked around the country today that produce over 10 000 ounces with the largest, Boddington, having an output of over 400 000 ounces. In total these mines produced an estimated 210 tonnes of gold in 1989 and we expect this year, 1990, that a new record production of between 240 and 250 tonnes will be set. This positions Australia in third place in the Western World behind South Africa #1 and the USA #2 and fourth in the world with the Russians holding second place overall behind the South Africans.

Jan 1, 1990

By Selim Coskun

In this study, tungsten matrix composites reinforced with 2 wt% TiC particles were mechanically alloyed (MA?d) for 3h, 6h, 12h and 24h. 1 wt% Ni is used as sintering aid which is added before and after mechanical alloying. Microstructural and phase characterizations of composite powders and sintered samples were carried out via SEM and XRD analyses. Furthermore, density and hardness measurements of as-consolidated and sintered samples were carried out. Additionally, DSC experiments were conducted to investigate the sintering behavior of the MA?d powders.

Jan 1, 2009

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

The tenth annual Mine Resale Evaluation was held in conjunction with the RMCMI 2001 convention at the Steamboat Springs Sheraton Resort, Steamboat Springs, Colorado June 23 through 26. The purpose of the mine rescue evaluation program is to provide an opportunity for mine rescue teams to learn new skills and improve their existing ones in a non-competitive environment. Several staged ?disaster? scenarios were held where the teams are called upon to exhibit their life saving abilities. The evaluators meanwhile are offering suggestions, both verbal and written, to help the teams better understand the situations presented them. This non-competitive environment allows the teams to work together and share their knowledge with fellow mine rescue teams providing everyone with a positive learning experience. Mine Rescue Chairman Bill Balaz, Balaz & Associates, was in charge of coordinating the events. Six teams consisting of seven to twelve members each (totaling 60 members) participated in the three-day event. Each ream was required to respond to direr different real-life scenarios plus a written general knowledge test daily. Cindy Burnham has assisted Bali, for a few years. Her responsibilities include grading all of the written tests. This year's tour professional evaluators included Art Seanz (Hazardous Ma¬terials) of Western Environmental Associates ; Guy Norton (Ropes), Guy Horton Rope Rescue; Mary Bailey (Medical), MBA Training and Morley Hense (Confined Space). Carolyn Durga, BHP Coal, also assisted in hazardous materials and medical scenarios. They each provided three different challenging mock situations per day per team. The teams had no prior knowledge of what the scenarios would be as details were provided only as they arrived. Ten volunteer victims added much drama and excitement to the event. Their realistic enactment, complete with false blood makeup and severed limbs, made for some very tense scenarios. The Mine Rescue Teams participating this year were BHP LaPlata, BHP Navjo, BHP San Juan, all from Farmington, New Mexico; Bridger Coal Co., Rock Springs, Wyoming; Sabine Mining, Longview, Texas; Solway Minerals, Green River, Wyoming and Western Energy Co., Colstrip, Montana. Many new friendships were made and much knowledge shared. A swap meet was held Saturday afternoon for the teams to exchange miscellaneous equipment, hats, shirts, etc. The trams were asked to evaluate the program and the evaluators. They responded with many positive suggestions that will help improve the upcoming events in the years to come. Culmination of the Mine Rescue program was a Tuesday morning awards breakfast where the teams were presented with trophies. Each member was also given a gold pin with the words Continuing Challenge - Ropes.' The pin was the first in a series that will be given over the next few years. The participating victims and evaluators were also commended for their outstanding efforts. Special signed "Victim" shirts were given to select volunteers. Sponsors for the Mine Rescue program were Flanders Electric Motors, Magnum Metals, Rocky Mountain Electric Motors, Sedona Consulting and Balaz & Associates. Many hours of volunteer tine and effort from various family members of participants helped make the 2001 event a huge success.

Jan 1, 2001

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By J. B. Carman

This paper, describing the mining practices and methods at the mine of the Molyb¬denum Corporation of America, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The mine of the Molybdenum Corporation of America is in the Red River mining dis¬trict, Taos County, northern New Mexico (fig. 1), The mill and camp are in the valley of Red River, about 7 miles east of the town of Questa; the mine is 1 ¼ miles away, in Sulphur Gulch, a tributary of Red River. The mine is about 600 feet higher than the mill, at an altitude of about 8,700 feet. The climate is cold in winter, but does not interfere serious¬ly with continuous operation. The mine normally produces about 40 tons of sulphide molybde¬num ore per day, which is concentrated at the local mill and chipped to the plant of the Molybdenum Corporation at Washington, Pa.; there it is made into either ferromelybdenum or "molyte" (calcium molybdate), for use in alloys. The ore is mined from narrow, irregular veins by the cut-and-fill method. About 65 men are normally employed underground and on the surface at the mine.

Jan 1, 1931