Search Documents

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By Diogo de Oliveira Azevedo

No presente trabalho, processos de conformação a frio e recozimento foram aplicados à liga de magnésio ZK60A (Mg-6%Zn-1%Zr) com o objetivo de determinar a cinética dos fenômenos de recuperação e recristalização para permitir o refino de grão. Para tanto, foi desenvolvida uma série de matrizes de conformação para a trefilação incremental de barras circulares da liga ZK60A inicialmente recebida no estado envelhecido (T5), resultando em reduções de 7,8%, 15,4%, 22,6% e 29,4%. Após cada passe de trefilação, as propriedades mecânicas do material foram determinadas. O estudo do recozimento foi realizado em amostras com o máximo encruamento a temperaturas de 400°C, 350°C, 300°C, 250°C, 200°C e 150°C. Pela metodologia aplicada, foi possível avaliar a cinética do processo de recristalização da liga ZK60A e determinar a sua energia de ativação.

Aug 8, 2018

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By V. G. Minenko, V. A. Chanturiya, A. L. Samusev

Eudialyte is one of perspective resources of zirconium and other rare earth elements (REEs). Large reserves of eudialyte concentrated in the Murmansk region of the Russian Federation. Usually, technologies of REE treatment include the decomposition of eudialyte concentrate in different acidic, extraction and utilization of all components. The main problems in the leaching of eudialyte include are: the formation of an unfiltered silicon-containing gel; low recovery of REE; difficulty extraction of metals from the productive solution; high aggressiveness of the reagents. One of the promising trends of intensification of the processing of hard-to-degrease rare metal raw materials is the use of energy methods for affecting mineral suspensions. These methods make it possible to increase the efficiency of break up fine-dispersed mineral complexes and extracting micro- and nanoparticles of a valuable component in subsequent deep processing. The purpose of this work is to investigate the effect of energy impacts on the nitric acid leaching of eudialyte concentrate. Experimental studies were carried out in a developed laboratory facility that makes it possible to evaluate the effect of electrochemical, ultrasonic and combined effects on the leaching of zirconium and REE from eudialyte concentrate. The studies carried out on the samples of eudialyte concentrate with the size class of -0.315 + 0.063 mm showed that the use of electrochemical and acoustic effects increases the extraction of ZrO2 in the production solution in 1.6 - 2.5 times, REE in 1.3 - 2.2 times, respectively. An analysis of the microstructure and phase composition of the surface of the eudialyte concentrate showed that the intensification of the leaching process is due to surface cleaning from the silicon-containing gel, as well as the opening of capillary channels and microcracks, which accelerates mass-transfer processes. The results obtained open wide opportunities for creation of modern and effective technology of processing of eudialyte concentrate, producing high-quality zirconium products and REE.

Jan 1, 2018

By Carlos G. C

Geological mapping in various parts of Australia is revealing a number of regional associations of mineralizations with particular persistent stratigraphic horizons. Such associations have been found in the Broken Hill district of New South Wales, in the Nairne district of South Australia, in the Mount Isa district of Queensland, and in the Cloncurry district of Queensland. The question has arisen as to whether such mineralizations are of sedimentary origin, syngenetic with the enclosing formation, or whether they are of epigenetic origin, and reflect the selective hydrothermal mineralization of favourable beds on a regional scale.The purpose of this investigation is to test the use of sulphur-selenium ratios as an objective method of distinguishing between suphide deposits or sedimentary or supergene origin, and sulphide deposits of hydrothermal origin, with particular application to the districts mentioned. At the same time much data has been accumulated as to the selenium content of Australian sulphide ores. The possible use of sulphur-selenium ratios for this purpose was first demonstrated by Goldschmidt and his coworkers (1933; 1935), and later by Carstens (1941). Goldschmidt and Strock (1935) found that pyrite of sedimentary origin had a sulphur : selenium ratio of the order of 200,000 or more, whereas pyrite of hydrothermal origin had a sulphur: selenium ratio of 10,000 to 20,000. Carstensfound that sedimentary pyrite deposits in Norway contained less than 1 g. Se per ton, whereas hydrothermal pyrite deposits contained 20 to 30 g. per ton.

Jan 1, 1954

By Kim B. Shedd

An initial evaluation of the flow of cobalt-containing materials in the United States was prepared. The following aspects of materials flow were included: cobalt released as a result of mining and processing other metals and minerals; scrap generation and subsequent recycling or cobalt recovery; and cobalt losses resulting from the generation of wastes, dissipative uses, and disposal of used products. Where possible, estimates were made to quantify the amount of cobalt lost from the materials flow. More than 2,000 metric tons (mt) of cobalt are released annually from mining and mineral processing in the United States, including 480 mt of cobalt in coal produced in the United States. Metallurgical industries examined in this study have well-established recycling or cobalt recovery practices. The petroleum industry recycles spent catalysts, and some chemical catalysts are also recycled. Losses generated during cobalt chemical and powder processing were estimated at 50 to 80 mt of cobalt annually. Losses from alloy processing and the manufacture of parts and products were estimated to be 360 mt. These industrial losses are greatly outweighed by an estimated 2,780 mt of cobalt&apos; consumed in the United States each year to make products that will ultimately be disposed of.

Jan 1, 1992

By S. H. Boshlov

Los problemas del diseño estructural de minas se basan en numerosas complejidades como el de una incapacidad para definir explícitamente los parámetros, físicos in situ del medio rocoso y sus materiales asociados, el comportamiento del sistema bajo alguna descripción bosquejada de la aplicación de la carga; otras proceden de la incapacidad para especificar con precisión el estado inicial de la tensión en el medio. En ese sentido, el presente texto señala un modelo de diseño estructural manipulable donde se refleje el comportamiento del prototipo que representa. Así, el análisis por elementos finitos, en el cual la estructura se considera como una reunión de numerosos elementos, cuyas propiedades individuales pueden señalarse a voluntad, indica la posibilidad de un problema de diseño de una estructura minera como un ejercicio de análisis de sistemas. Tal sistema rocoso podría incluir todos los factores naturales y los medios ambientes artificales que afectan la resistencia de las estructuras mineras de superficie interior.

Nov 1, 1971

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By E. V. Lilford

Valuators of mineral properties are faced with a range of valuation methodologies, the most important of which are grouped under the headings of the market approach, the cost approach and the income approach. The way in which value is defined and the detail of the different valuation methodologies is examined here. This paper aims at documenting the variety of valuation procedures and applying each method to a variety of gold projects and comparing the outcomes. Any decision to apply a valuation technique will depend principally on the stage to which the project has been developed. The valuation approach to a greenfield project will be substantially different from that applied to a well-drilled, extensively explored mineral property. Furthermore, a valuation exercise may produce different outcomes for the same gold project depending on which method is applied. In order to investigate the variability in valuation methods and to explore the outcomes of different approaches, a series of five gold projects was analysed. The projects differ in regard to levels of capital application, infrastructural setting, depth below surface, in situ grade, and the stage of development, and were valued using the different methods. The most critical aspect of any valuation is the capacity of the valuer to identify the salient issues and ensure that they are incorporated into the valuation. The danger of simply applying ?black box? solutions to valuation problems without a full understanding of the parameters and the areas of uncertainty is emphasized. The importance of the valuator?s experience, insights into best practice and the ability to recognize and submit to the requirements of compliance within the minerals industry is among the most important characteristics of a valuer.

Jan 1, 2005

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969

By R. P. King

The MODSIM mineral processing plant simultor is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open- and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Feb 24, 1997

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

By C MacDonald

There are many technologies available today in terms of fire and life safety in road tunnels. So many in fact that it is becoming more and more difficult for clients and contractors alike to determine what they want and what they need. From a clientÆs perspective, fire and life safety is about protection to its infrastructure and to the public at large. Conversely, the contractor is looking to meet its æfit for purposeÆ or ædeem to complyÆ requirements in the most economic and practicable way. Practices regarding fire and life safety in road tunnels have undergone a degree of transformation during the last decade or more throughout the world. This transformation has largely been driven by a series of catastrophic accidents such as the major fires in Europe including the Mont Blanc Tunnel, Tauern Tunnel, Saint-Gothard Tunnel, and now most recently in the CityLink Tunnels in Melbourne. International guidelines produced by organisations such as the Permanent International Association of Road Congresses (PIARC), the European Union, the International Tunnelling Association (ITA) and the US National Fire Protection Authority (NFPA) now provide clients, owners and designers with the tools required to define and specify the required fire and life safety systems in road tunnels. The majority of these tools are based on risk assessment and risk management. Recent road tunnel projects within Australia, however, have not referred solely to such guidelines. Clients have opted to prescribe different or additional fire and life safety requirements within the projectÆs technical specification documentation (project requirements), leaving designers and contractors with little room to implement alternatives or substitutions. Further, these project requirements are largely dictated by practice established on previous road tunnel projects within Australia. This paper looks at the current international guidelines and practices and undertakes a comparison with the EastLink tunnels in Melbourne and other road tunnels within Australia and makes assessment on whether Australian methods are the most appropriate for clients and contractors alike. Focus is directed to the key elements of fire and life safety such as:traffic envelope, barrier arrangements and emergency walkway provisions;deluge systems;drainage systems;fire rating requirements;tunnel ventilation systems;cross passage provisions;fire safety assessment;critical intelligence systems including help phones, CCTV, incident detection, tunnel signage, etc; andexternal tunnel control systems.

Jan 1, 2008

Rock mass classification is widely used throughout the underground mining industry—in both coal and hard-rock mines. It is used in all stages of the mining process, from site characterization to production operations. The goal of the International Workshop on Rock Mass Classification in Underground Mining was to provide a forum for leading practitioners of rock mass classification to come together and share their methods and experiences with the technique. The workshop was held in Vancouver, British Columbia, Canada, on May 31, 2007. It was co-chaired by Christopher Mark, Ph.D., P.E., National Institute for Occupational Safety and Health, Pittsburgh, PA, and Rimas Pakalnis, P.Eng., University of British Columbia, Vancouver, Canada. The proceedings of the workshop contain 16 invited papers from 9 countries, reflecting the international depth and breadth of current practice. Applications in both hard-rock and coal mining are well represented. Some of the topics that were addressed at the workshop include: • Major rock mass classification systems used in mining and their variants • Collection of input data through observation, rock testing, and geophysics • Design of mine layouts and rock support systems using classification • Estimation of rock mass strength and other input parameters for numerical models from classification • Applications in weak rock, raise boring, cavability assessment, and other special topics • Risk assessment using rock mass classification

Jan 5, 2007