Search Documents

By P. Marier, T. R. Ingraham

When cylindrical powder compacts of nickelous oxide (NiO) are heated in an equilibrated stream of SO3, SO,, and 02, in the temperature range 500°to 800°c, tlickelous suljate (NiSO4) is formed as an adherent layer on the oxide. The reaction is diffusion-controlled, with an activation energy of 13 ± 3 kcal per mole. When cylindrical powder compacts of NiSO4 are heated in a stream of dry nitrogen in the temperature range 1000 0to 11500C, NiO is formed at a well-defined interface between the sulfate and oxide. The interjhce migrates into the sulfate at a constant rate at a constant temperature and gas flow. The reaction rate increases with increasing gas flow and decreases with increasing partial pressure of SO3 in the gas stream. Resolution of the partial-pressure data with a Lang-itzliir Adsorption Isothern suggests that about 80 pct of the NiO interface is covered with SO3. The heat of adsovption is about 68 kcal per mole. The activation energy of the decomposition process is 61 ± 3 kcal per mole. MOST of the work reported on the formation and decomposition of nickel sulfate is related to thermodynamics.1-3 No quantitative work has been reported on the decomposition process. The only kinetic work reported on the formation is that by Fletcher and shelef.4-6 whose main purpose was to study the effects of alkali metal sulfate additions on increasing the rate of nickel sulfate formation. They found that, in the absence of an additive, only small amounts of sulfate were formed and the kinetic data were difficult to interpret. However, they suggested that the sulfa-tion of nickel oxide is a diffusion-controlled process for which the activation energy is approximately 17 kcal per mole.6 In this paper, both the formation and decomposition reactions will be examined; and based on the effects of temperature, flow rate, interfacial area, and partial-pressure of sulfur trioxide, mechanisms and activation energies will be suggested for both processes. EXPERIMENTAL Material. The nickel source material used in all experiments was Baker and Adamson Reagent Grade NiSO4. 6H2O, for which the following analysis was supplied by the manufacturer: C1, 0.001 pct; NO3, 0.005 pct; Co, 0.02 pct; Cu, 0.005 pct; Pb, 0.002 pct; Fe, 0.001 pct: insol, 0.005 pct. The anhydrous sulfate was prepared by heating the hydrate at 420°C in a muffle furnace for 5 hr. Nickel oxide was prepared by decomposing the sulfate at 950°C over a period of 10 hr. Method. The technique used for measuring the rates of formation and decomposition was developed earlier in these laboratories.7-8 The method is based on the observation that the kinetic parameters of a reaction can be established in a flow system, with specimens prepared by compacting powder to a uniform pellet shape. The results are identical with those established with solid polycrystalline specimens or single

Jan 1, 1967

By L. W. Scott

This report presents an overview of explosionproof (X-P) enclosure research being conducted by the Bureau of Mines, This report emphasizes the increasing importance of research related to the safety con- siderations of X-P enclosures used in underground coal mines. Selected topics are included that summarize results of research in the areas of electrical clearances, reliability of enclosures with windows, safety factors in X-P enclosures, potting materials, performance tests for X-P enclosures, protection against high-voltage explosions, and innovative X-P devices.

Jan 1, 1985

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3'1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

The paper covers the history and develop- ment of electrical and diesel-powered hydrau- lic percussion rock drills. It examines main design aspects and problems encountered in pro- ducing an efficient and reliable machine to fully cover the nominal hole sizes required for underground development, production drill- ing and for general quarry work. The main design features and advantages of a hydraulic rock drill are relatively low input power requirement to energy per blow (this being achieved by the use of an electric or diesel- powered hydraulic system) and a specially con- structed piston using a powered damper cylinder to absorb the recoil forces from the drill steel and reduce stresses on the drill, feed and hydraulic boom. A further important design feature is the anti-jamming device which controls the drill both during manual and automatic operation. This anti-jam device works on feed and rotation press and prevents the drill bit becoming jammed in broken or soft ground. These features and many other mechanical and environmental benefits are highlighted when comparing hydraulic percussion rock drills with current pneumatic machines. The hydraulic rock drill gives an overall high penetration and production rate, with an added bonus for ergonomy and environmental conditions such as lower noise level, no fogging from air and oil exhaust (which naturally gives better air for breathing),plus improved vision when in under- ground situations. Hydraulic rock drills and systems have been fully tested in many mines, quarries and contract sites during the past years. They h6! been improved and modified and are now provi~ to be very reliable and economical piece drilling equipment whò in mines and quarries.

Jan 1, 1978

By H. T. Fargey

This paper considers the social, economic and political factors and their influence on future production and marketing of Western Canadian minerals. Among the subjects discussed are inflation, taxation, anti-combines legislation, unstable international currency relationships, economic nationalism and protectionism, the European Common Market and environmentalism.

Jan 1, 1973

By R. T. Elworthy

Canada ranks second in the list of world consumers of natural gas. In 1923 our production was nearly fifteen million thousand cubic feet valued at $5,800,000. Our output, however, appears very small compared with that of the United States, which in 1923 totalled over one thousand and eight million cubic feet, valued at $240,000,000. Natural gas is found in commercial quantities in three? provinces in Canada. New Brunswick: Natural gas in New Brunswick has been utilized commercially only since 1912,although the investigation of oil and gas possibilities of the province commenced as early as 1859. The annual production is a little more than one-twentieth of the total Canadian production and remains fairly constant from year to year. Ontario: In Ontario the earliest gas wells were drilled in Essex and Welland counties between the years 1885 and 1890. On account of the small demand in Canada the cities of Detroit and Buffalo were supplied with large quantities of gas from these wells, but this export was curtailed in 1898 and finally ceased in 1900. The production of natural gas in Ontario, mainly from fields in Lambton, Kent, Essex, Norfolk, Haldimand and Welland counties, increased rapidly from 1900 until the peak was reached in 1917, when over nineteen million thousand cubic feet valued at $3,641,587 was consumed.

Jan 1, 1925

By C. N. Logan

The Southern Company is one of the nation's largest electric utilities and is the parent firm of five operating companies: Alabama Power, Georgia Power, Gulf Power, Mississippi Power and Savannah Electric and Power. Another subsidiary is Southern Company Services (SCS) which provides engineering and technical sup-port to the five operating companies. This technical support includes the procurement and supply of over 40.9 Mt (45 million st) of coal annually for the 22 coal fired plants in the system. Approximately 80 percent of this tonnage is purchased under long term contracts and the remaining 20 percent is purchased on the spot market. The coal is principally supplied from Alabama, Illinois Basin and the eastern Appalachian coal fields. Most of the coal is delivered by unit train and barge but one plant in Alabama receives all its coal by truck and conveyor belt.

Jan 1, 1990

By Truman P. Stauffer

Secondary use of mined-out space in underground limestone quarries is emerging in the Kansas City area where abandoned quarry sites are being renovated into warehouses, factories, and offices. Mining techniques, ceiling heights, and pillar distribution are being altered as planning for the secondary use of mined-out space is combined with the quarrying process. Even the historic urban- quarry land use conflict invites a reappraisal in that this development provides a potential resolution of the problem. Mutual subsidization by dual rock and space interest is changing the economics of rock production. A city is much more than a surficial adjunct superimposed upon the topography of an area. Its development and growth are deeply rooted in the resources, benefits and problems of its underlying geology. The environmental geologist must address himself to more than the quality of a particular resource. He must comprehensively relate resource extraction and processing with the urban emphasis of optimal use which favors long term usage of land over one time economic ventures. Limestone quarrying, closely allied with the growth of many cities, has commonly left a series of scarred landscapes in the path of the burgeoning metropolis. These abandoned quarry sites are barriers to orderly city growth and fail to serve the people as useful and taxable land. Where quarries are functional, supplying the city with needed growth minerals, problems of blasting damage, noise, and dust exist. Technology faces the challenge of making mineral production and processing good neighbors to the urban market they serve. Continued growth of cities may require more efficient use of space below as well as above the surface optimizing land usage so that long term economic benefits may be reflected in improved mining methods.

Jan 1, 1973

By G McSpadden

At September 2001 the beneficiation plant at BHP Billiton Iron OreÆs Mt Whaleback mine is set to treat 9.5 million tonnes per annum (Mtpa) of iron ore, 40 per cent better than original design. This paper describes the steps, decision-making processes and innovations used to increase capacity at minimum cost. The plant was designed in 1979 to operate at 1133 t/h for 6000 hours per annum, treating 6.8 Mtpa. Sufficient suitable contact ore was unavailable and feed was finer than planned. The plant was designed with minimum surge capacity between multiple process units. It had never reached design capacity. In 1993 a study by Fluor Daniel to treat increased tonnage resulted in modifications to improve plant operations. Efforts to expand production by increasing reliability did not achieve the desired capacity. NJ Morrow (Pty) Ltd (NJM) conducted a technical audit in 1996 with process evaluation by Mineral Processors. Replacement of operator interface and PLC logic in 1997 made plant operation and diagnosis easier. Involving operators in logic development enhanced their plant knowledge. Fluor Daniel Simulation developed a simulation model of the process. Mineral Processors and NJM reviewed the model findings, recommended metallurgical improvements and developed preliminary designs and costs. BHP Engineering produced a detailed design with a cost estimate of $A34 million. After analysis and revision of the design, a $A10.4 million upgrade to 8.5 Mtpa was carried out. Detailed modifications to the process units, particularly the HM drum plant, allowed significantly higher capacities and improved metallurgical performance. The target capacity was achieved in June 2001. Further modifications are progressing to treat lower-grade ores.

Jan 1, 2002

By G. Y. Chin, M. T. Dolan, W. L. Mammel

We have obtained by computer methods the solutions of the Taylor analysis1 for axisymmetric flow in bcc metals. Four modes of slip have been treated in detail:2-4 (111), {112}(111), {123}( 111), and a mixture of all three. In addition to obtaining anisotropy of strength data for randomly oriented or textured polycrystalline material,4 we have also obtained the lattice rotation resulting from slip on the predicted systems. The patterns of lattice rotation are essential to an improved understanding of texture development during deformation. The present note shows the results of lattice rotation for 5 pct axisymmetric compression, for fifty-two axial orientations distributed at 5-deg intervals throughout the standard stereographic triangle. The data are presented in Figs. 1 to 4 for the four modes of slip. The lattice rotation is indicated by a vector, the ends of which correspond to the positions before and after the deformation. The different vectors emanated from a given orientation represent different combinations of five slip systems that satisfy Taylor&apos;s minimum shear criterion.&apos; Fig. 1 shows the results for {110}< 111> slip. They are similar to those obtained by Bishop5 for the case of (111 )(110) slip in axisymrnetric tension, since in axisymmetric flow the sense of lattice rotation for {111)( 110) in tension is the same as that for (110) (111) in compression. The pattern of lattice rotation may be divided into three regions: region A in which the rotation is toward [100]; region B, toward [lll]; and region C, toward either [ loo] or L lll]. Although some slip combinations in region C lead to [1101, the latter is not stable as continued activity of the same combinations will eventually move the axis toward [loo] or Llll]. It may also be noted that [loo] is itself not stable. However, close inspection of the vectors in region A shows that it is impossible for an axial orientation within A to rotate outside its boundary. Hence after heavy compression, all orientations from A and some from C are expected to form a diffuse band in the [100] vicinity. By far the largest region is B. Here all orientations rotate to [lll], which is a truly stable position. Thus the [111] texture component is expected to be rather sharp. For the case of (112 }( 111) slip, Fig. 2, region C is enlarged at the expense of A, with B about the same as for {110}( 111) slip. A significant difference, however, is that [loo], as well as [Ill], is now truly stable. Fig. 3 shows the results of slip on {123}( 111) systems. Region B is substantially enlarged at the expense of C, with A being intermediate in size between the {110}(111) and {112}(111) cases. Like the case of {110)( 111) slip, [100] is itself unstable. However, the lattice rotations here are confined to less than 5 deg; hence it may be considered "stable" for practical purposes. Finally, Fig. 4 shows the results of mixed slip. Here region B is the largest, and C the smallest, of all the cases considered. Both [loo] and [ill] are stable. The behavior of the three corner positions is, in fact, identical to the case of {112)( 111) slip, Fig. 2; it turns out that in these positions for the mixed slip case, all the active slip systems (based on Taylor&apos;s criterion) belong to pure {112}( 111) .4 In summing up the results for the four modes of

Jan 1, 1968

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot&apos;s reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By L. M. Barker

The New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. History Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper. Geology Description of the geology of the Ajo district has been published by Ira B. Joralemon5 and by James Gilluly.6 The ore occurs chiefly in the porphyritic facies of Cornelia quartz monzonite, though appreciable

Jan 1, 1939

By L. M. Barker

The New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. History Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper. Geology Description of the geology of the Ajo district has been published by Ira B. Joralemon5 and by James Gilluly.6 The ore occurs chiefly in the porphyritic facies of Cornelia quartz monzonite, though appreciable

Jan 1, 1939

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed &apos;jetted particle drilling&apos;7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited&apos;s T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D BARRON J V. N DORR Engineering Societies Library Board ROBERT PEELE PHILIP W. HENRY GEORGE C STONE JOSEPH E. POGUE The Engineering Foundation H C BELLINGER GALEN H CLEVENGER J V N DORR

Jan 1, 1923