Search Documents

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By P. G. Rueffel

"Natural deposits of sodium sulphate are the result of normal geological processes. They are world-wide in occurrence and are found in depressions in arid and semi-arid regions. Primarily, the sodium sulphate deposits of the prairies are post-glacial and differ from rock salt deposits, which originated from connate water (fossil sea-water). Sodium sulphate on the Canadian prairies occurs as brine or in beds of intermittent and/or permanent crystals. Most beds are contaminated with various amounts of silt, sand and decayed organic matter. Soluble impurities such as chlorides, carbonates and bicarbonates of sodium and sulphates of magnesium and calcium are leached out from the soil of the surrounding run-off area of the deposits.In this paper, the origin of sodium sulphate, and the physical and chemical aspects related to the development of the Ingebrigt Lake deposit are dealt with. The problems of garnering raw material, and of refining and de-hydration are discussed, with emphasis on the Ingebrigt Lake plant. The utilization of the ""Total Power Concept"" in a sodium sulphate plant is described. The principal uses of sodium sulphate are also discussed."

Jan 1, 1968

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By S Hille, J Karageorgos

With the increased variability of todayÆs large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

By Sarah Wilson, John Kaplin

Plans are underway to extend commuter rail service underground into downtown San Francisco. The Salesforce Transit Center (STC) was completed in 2018 and will serve as a new transit hub, including a commuter rail station after two future connecting tunnel segments are completed. The northern segment, known as the Caltrain Downtown Extension (DTX), which will extend the rail line from its current terminus at 4th and King Streets to the STC, is currently in Preliminary Engineering. The southern segment, the subject of this paper, is a 1.6-mile tunnel known as the Pennsylvania Avenue Extension (PAX), which is currently in the pre-environmental planning stage, with alternative alignments under evaluation including single bore versus twin bore options. This paper discusses project challenges, including highly variable tunneling conditions in soil and rock, a congested urban project site with limited space for construction staging, alignment crossings of large existing buried infrastructure, and complicated interfaces with future and existing rail operations.

Dec 1, 2022

By H. C. Fuller

Submerged combustion and inverse solubility methods were investigated as promising alternative means for crystallizing manganese sulfate from solutions produced by leaching manganese ores with either sulfuric acid or sulfur dioxide. Evaporation of water from typical manganese sulfate solutions by sub-merged combustion techniques enabled production of a slurry containing 32 to 39 pct MnSO4.H2O crystals suspended in a saturated solution of manganese sulfate. Such a slurry required further processing by thickening or filtration and drying to produce crystals of MnSO4.H2O. In a second approach, semicontinuous processing of manganese sulfate solu¬tions by thermal crystallization under pressure effected a recovery of 94.5 pct of the MnSO4.H2O as dry free-flowing crystals. Treatment of a solution containing about 100 grams manganese per liter at 189° C, produced a "barren" solution containing only 1.9 grams manganese per liter. Calculations made on comparable manganese sulfate solutions show that the heat requirement of the thermal crystallization method was about one-third to one-fourth that of the submerged combustion method.

Jan 1, 1966

By F. X. Tartaron

This report describes work done by the Bureau of Mines to simplify the design and operation of the vortex cone, a new device for prerefining blast furnace iron. Three new apparatus arrangements were tested. Results with one of these arrangements average 74.2 pct silicon removal and 61 pet oxygen efficiency (disregarding removal of carbon and manganese).

Jan 1, 1965

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By James H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse circulation air lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll- Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1976

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By Sunil G. Warrier

A rapid infrared forming technique has been developed to fabricate titanium matrix composites. This technique applies infrared heating to infiltrate titanium alloys into carbon and silicon carbide prepregs. The entire process typically takes 1-2 minutes in an inert atmosphere. The advantages of this technique are that the process is fast, simple, does not require a vacuum or a high external pressure. The process is very economical both in energy conservation and operation costs. This technique has been used to produce void free composites with limited, well controlled fiber-matrix reactions and mechanical properties comparable to currently available titanium matrix composites.

Jan 1, 1993

By R W. Hutchinson

Cupreous pyrite deposits in Cyprus have many geologic similarities to Canadian massive sulphide copper-zinc ores as well as certain significant differences. A comparison of the Cyprus and Canadian deposits indicates a complex genetic history for the latter and suggests that their origin should be re-examined. The Cyprus ores occur in subaqueous extrusive rocks near and at the top of a Cretaceous volcanic pile or igneous complex. The rocks have not been deformed, nor have they been deeply buried or deeply eroded. Apparently the ores formed near or at surface in the top of the volcanic pile by a volcanic-exhalative process and from an ore-fluid of volcanic derivation. The Canadian deposits are of comparable composition and have similar geologic set-tings, but occur in the most ancient Precambrian rocks. Their enclosing Keewatin greenstones have, in most places, been deformed, regionally metamorphosed and invaded by granitic intrusions. Comparison suggests that the Canadian ores also formed initially near surface in ancient Keewatin volcanic complexes by a syngenetic, volcanic-exhalative process. Subsequently, during orogenesis, they were deformed, remobilized under conditions of elevated pressure-temperature and re-emplaced as epigenetic bodies into

Jan 1, 1965

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019