Search Documents

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of nine manganese-ore samples in 1953-1954. Three samples were from Nevada and the other six from California. These samples represent marginal or low-grade ores from deposits that have been mined selectively in the past. The present interest lies chiefly in the possibilities of concentration of the remaining low-grade ores for economical exploitation. The treatment methods included gravity concentration and flotation in most cases. Results were sometimes unsatisfactory, particularly when the ore was too fine grained for liberation of the minerals within economical grinding range. The contaminating gangue minerals, such as quartz and iron oxides, were locked with the manganese to an extent that prevented separation of high-grade concentrates with satisfactory recovery. In cases where fairly good concentrates were made, it was at the expense of recovery, a condition typical of low-grade ores.

Jan 1, 1955

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By R. K. W. Merkle, F. A. S. Reyneke, Z. Harris, P. W. J. Delport

The technological advancements in computing power in the last 30 years have enabled the practical visualization of complex geological environments in three-dimensional (3D) space. 3D models and their application in the mining industry are becoming increasingly important, for example, to identify future exploration areas and targets, for mineral assessment and evaluation, and prediction and planning of future drill-holes. However, acquiring borehole data is an expensive practice, with drilling programmes costing mining companies up to billions of dollars each year. Tighter financial constraints on exploration budgets result in more pressure being put on three-dimensional models to accurately identify future target areas. This article aims to evaluate the potential drilling success of simulated greenfield and brownfield exploration using a 3D geological model created of Leeuwpoort tin mine. These simulations investigate the probability of intersecting a mineralized zone of economic interest and evaluate how the probability is affected when the number of drill-holes and distance from a known intersection changes. Furthermore, these simulations attempt to obtain an indication for the minimum number of drill-holes required for a successful exploration campaign at the mine. The investigation also aims to establish a first-pass attempt towards developing a ‘favoured procedure’ for identifying potential exploration targets for tin deposits with geological and geochemical characteristics similar to Leeuwpoort. The results for the ‘favoured procedure’ established are statistically tested using the ‘bootstrapping’ method. By simulating various exploration scenarios, the study also emphasises the importance of predicting successful drilling, which aids in budgeting for drilling programmes as the minimum number of drillholes needed for a specific exploration project can be determined.

Feb 2, 2022

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By Bertrand L. Johnson

As potash is more necessary to the agricultural economy of the United States now than ever before it is gratifying to find that the virtual stoppage of imports from Germany in late 1939 caused none of the anxious foreboding that gripped American farmers in 1914. For long decades this country, in common with tie rest of the world, depended upon German potash, but today our expanded needs can be mot from domestic sources. The present armed conflict in Europe, like that of 1914, disrupted a world monopoly, but the cartel that in recent years controlled 90 percent of the world output (see fig, 1) was an international syndicate comprising French, Polish, and Spanish as well as German producers and having reported sales agreements covering production in the U. S. S. R. and Palestine. The break-up of these commercial agreements has necessitated readjustments but generates no such alarm as the closing of a single source of supply. In striking contrast to the critical shortage that developed a quarter century ago, no increase in prices has occurred or is anticipated in the domestic market.

Jan 1, 1940

By Paul M. Tyler

Hafnium appears to be among the more abundant of the newly discovered elements . Though quite widely distributed in nature , its compounds chemically so resembled those of zirconium , its sister element , that it escaped detection until 1923 , when Coster and Hevesy announced the discovery of the element , to which they gave the name of " hafnium " , from Hafniae , the Latin name for Copenhagen , where their research work was performed . Hafnium has so far been found only as a minor constituent of zirconium minerals . Zirconium as an element was discovered more than 140 years ago , but only a few unimportant uses were found for the metal or its compounds until some 18 years ago ; it is still classed among the rarer commercial metals . It is not surprising , therefore , that hafnium has not yet found a definite place for itself in industry . Nevertheless it has commanded a considerable interest among scientists ; and in 1930 some 70 grams of perfectly pure oxide of hafnium were prepared in Europe . A commercial future for hafnium is already glimpsed in the radio industry , and its high melting point and electronic emissivity have already led to the taking out of patents for its use in radio tubes and incandescent electric lamp filaments and for the cathode surfaces of devices such as X- ray tubes and rectifiers .

Apr 1, 1931

By H Guthrie, J Hodder, J Bain, S Durkin

Australian mines have traditionally relied on diesel powered vehicles to fulfil their light vehicle needs. There are many reasons for the resources industry to review its use of diesel-powered vehicles. The international industry has developed projects to explore the use of Battery Electric Vehicles (BEV) as a more sustainable alternative to traditional diesel-powered vehicles. While the technology for cost-effectively applying modern high-performance lithium-based batteries to the mining environment has existed for over a decade it is yet to be widespread throughout the industry. Through the collaboration of Safescape, 3ME Technology and Kirkland Lake Gold, with funding from Mining Equipment technology services (METS) Ignited, the project has focussed on advancing the Australian METS sector’s capability in the rapidly approaching implementation of BEV technology. This paper reports on the collaborative approach to develop a prototype vehicle; explains the selection criteria for the various components of the vehicle; and details the risk-based approach to developing a scalable product to replace existing underground light vehicle fleets. The prototype vehicle was tested underground at Kirkland Lake Gold’s Fosterville operations in Victoria beginning in October 2019. Reporting from these trials focusses on the key factors affecting underground operations. These include driveability, safety, charging and cycle times. Gathering data around energy consumption through normal daily duties enabled a model of energy consumption and charging requirements to be developed such that various applications of the electric vehicle can be considered against existing diesel-powered vehicles. This has provided insight into the impact on daily operations, and the way forward for large scale implementation.

Mar 15, 2021

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By James P. Ulery, Frank E. Chase

Clay veins found in coal mines have caused numerous injuries and fatalities. These structures plague all phases of mining, including entry development, pillar recovery, and panel extraction. Clay veins also increase production costs and may disrupt or halt mining. These detrimental aspects have prompted the Bureau of Mines to investigate the physical characteristics of and roof instability problems associated with clay veins. This was accomplished by observing and mapping clay veins in surface and underground mines. The occurrence and origins of clay veins were also investigated to determine predictive capabilities. The investigators found that clay veins normally occur in more stable, less rapidly subsiding coal basins. Clay veins result when tensile stresses develop fissures which are later infilled. These fissures can be propagated by compactional processes and/or tectonic stresses active during and subsequent to coalification. The Bureau also found that associated faults, fractures, and slicken-side planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance, the roof is segmented into cantilever beams, causing unstable conditions. Consequently, the strata on either side of the clay veins should be bolted and strapped together to form a beam.

Jan 1, 1987

By Luisa Perez, Carlos Perea

El método de explotación por subniveles es uno de los más utilizados en operaciones mineras de mediana y gran escala, como es el caso de la minería de zinc en Perú. Para seguir la secuencia de explotación, este método requiere el relleno de los caserones vacíos, como por ejemplo el relleno en pasta, el cual se produce mediante la mezcla del relave producto de la planta concentradora de mineral con un 3.5 % de cemento, con el fin de que dicho relleno actúe como pilares de gran dimensión que aporten el sostenimiento necesario a la mina (0,8 MPa). Sin embargo, esto genera una dilución con el mineral a explotar al momento de avanzar en los tajos aledaños. Por ese motivo, y por la necesidad de lograr la automatización de la operación minera, se decide evaluar el relleno detrítico cementado, evaluación que se realiza mediante el análisis de resistencia, estudios de factibilidad, rendimiento en costos, aumento de productividad y seguridad en la operación. El resultado son valores máximos de resistencia de los pilares de 1,6 MPa, que evitan la dilución y mejoran el porcentaje de recuperación de mineral.

Sep 20, 2019