Search Documents

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

In presenting this address I am conscious of the honour that has been paid me in my election to this important office, and I am very aware that I follow, in the position of President, many distinguished men who have led the Institute over the 70 years since its inauguration in Broken Hill in 1893.It is perhaps appropriate tonight that I intend to talk about a metal which recalls the birth-place of the Institute, and is also one with which I have had a direct association throughout the whole of my working career. This metal is Silver.Silver is associated traditionally in everyone's mind with money and silverware, and has always been prized for its natural beauty and elegance. It is today one of the few metals in which world consumption has outstripped production, and the events which have occurred to bring about this situation make an interesting story.In telling this story, I propose firstly to indicate our development as a silver producing country, give an historical review of the metal, trace its use as currency and the factors influencing its price, and then say something of the old and new uses of silver. Finally I shall give some comments on silver production in Australia today.Australia, with 6-5 per cent of the world's output of silver, ranks sixth among the producer countries and over the years has contributed 892.5 million ounces to the world's supply which, based upon production since the discovery ofAmerica, is estimated to have been 22,150 million ounces or nearly 680,000 tons.Although our production appears relatively small by...

Jan 1, 1963

By B. Hart, J. Marois

"Scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM–EDX), and Time of flight secondary ion mass spectroscopy (TOF-SIMS)were used to analyze pyrochlore grains from Niobec froth flotation plant. Samples from the mill feed, pyrochlore rougher feed, pyrochlore rougher concentrate, and tail were analyzed in order to identify a potential relationship between pyrochlore matrix composition and selective separation. SEM-EDX analyses indicate that pyrochlore grains with high Fe content appear to be less recoverable than those with a lower Fe content and that the flotation response is related to matrix Fe rather than Fe occurring as inclusions. TOF-SIMS was used to analyse the surface of high Fe and low Fe pyrochlore, in order to identify a potential relationship between pyrochlore matrix composition and the related effect on cationic collector adsorption (tallow diamine). Surface analyses of pyrochlore from a conditioning test show that species indicative of the collector favour the surface of Fe poor pyrochlore relative to the Fe rich variety. The results from the conditioning test illustrate a negative relationship between collector loading and the presence of Fe and related oxidation species. This study identifies the link between pyrochlore matrix Fe content and, the presence of surface oxidation products, to collector loading. Poor Fe rich pyrochlore recovery noted in the Niobec froth flotation plant may be partially explained by this mechanism.INTRODUCTIONPyrochlore, the most abundant niobium containing mineral (Perrault and Manker, 1981) is economically recovered in Brazil, China, and Canada (Niobec) (Kouptsidis et al., 2008). Since 1974 Niobec has been extracting niobium from the St-Honorécarbonatite deposit. Niobec is the only operating Nb extraction facility in North American and one of the three major world producers of ferroniobium (Dufresne and Goyette, 2004; Belzile, 2009).Flotation is the preferred and most cost-effective method for pyrochlore recovery (Burks, 1958; Shapolov and Polkin, 1958; Zakharov et al., 1967; Razvozzhaev and Nikiforov, 1972; Bogdanov et al., 1973; Abeidu, 1974; Raby and Desrochers, 1975; Wilson, 1979; Biss and Nadeau, 1982; Biss, 1985). With the aim of optimising the flotation process for the Niobec ore, numerous experiments were performed on the influence of surfactants and type of water to optimise pyrochlore recovery and grade during flotation (Gomez et al., 1987; Rao et al., 1988; Dufresne and Goyette, 2004; Belzile, 2009)."

Jan 1, 2013

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

By A. U. Seybolt

A FEW copper-zinc-base alloys meet die-casting requirements reason- ably well, although improvements are desired. Aluminum bronzes, high-tinbronzes and some copper-nickel-zinc alloys can be die-cast, accordingto Herb,1 but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. TABLE 1. Commercial Die-casting Brasses a Constituent Yellow Brass Low-silicon High-siliconb Brass Brass Nickel Silver Composition, Per Cent Cu 57-59 63-65 80 -81.5 42.0 Zn 40-42 33-35 13.5-16.0 41.0 Sn 0.5-1.5 Si 0.75-1.25 3.75-4.25 Pb 1.0 Ni 16.0 Properties Tensile, lb. per sq. in.. 55,000-60,000 65,000-70,000 85,000-95,000 85,000-95,000 Yield, lb. per sq. in.d.. 30,000-35,000 35,000-40,000 65,000-70,000 65,000-72,000 Elong., per cent in 2 in . 15-20 20-30 8-12 10-20 Brinell hardness 120-130 120-130 160-180 160 Specific gravity 8.47 8.50 8.15 8.45 Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy, 3,4 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. c Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb' as 1650° F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600° F., and of the nickel silver as 1675° F. d Criterion not stated.

Jan 1, 1939

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

The labour question is one that has caused mine managers much thought and anxiety and is likely to continue to do so as long as human beings exist. The difficulty is to devise some arrangement whereby the interests of miner and mine ownerare identical. Mines cannot be worked without capital, and capital is no good without labour, yet, though both have the mine in common, their interests are not exactly the same. Some men are happy so long as they can scrape through by exerting themselves as little as possible, but capitalists do not work mines for charity, they want some return for their money.Where a large number of men are employed there are bound to be examples of all sorts, good and bad, and it is because one cannot depend on all, that different methods of employment have to be adopted. Which method is selected depends to a great extent on the labour market, local conditions, nature of the ore and the way in which it occurs.A big step towards success is obtained by securing the services of good bosses, not only those who know how work should be done, but men who have a knowledge of human nature. It is a big mistake to be too lenient with a man, also to be unnecessarily harsh. A good boss will always be sought out by good men who have worked under him before, or who have heard of him from others. By a good boss we do not mean one who employs two men where one would do, or who lets the men loaf...

Jan 1, 1901

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By J. -P. Tshibangu, A. Vervoort, A. Lavrov

Abstract: The aim of the research presented is to study the effect of complex loading schemes on the fracturing process during loading and/or unloading. A first set of experiments was done using a poly-axial cell. These experiments in combination with numerical simulations showed a difference in micro-fracturing (shear and tensile cracks), but not in macro-failure between various loading/ unloading schemes. The second set of experiments was based on the three-point bending test and several cycles with or without rotation between cycles were applied. If the specimen was rotated by 90° or 180° about its long axis between the first and second cycle, no Kaiser effect was observed. Résumé: Le but de la recherche présentée est d’étudier l’effet de schémas de charge complexe sur le processus de fracturation durant la phase de charge et de décharge. Une première série d’expériences était réalisée utilisant une cellule polyaxiale. Ces expériences combinées avec des simulations numériques ont montré une différence de micro-fracturation (fissures de cisaillements et de traction) pour les différents schémas de charge et décharge, mais en ce qui concerne la macro-fracturation ce n’est pas le cas. La deuxième série d’expériences était basée sur des essais de flexion trois points avec plusieurs cycles, avec ou sans rotation entre les cycles. Si l’échantillon est tourné de 90° ou 180° selon le grand axe entre le premier et le second cycle, l’effet Kaiser n’est pas observé. Zusammenfassung: Der Zweck der vorliegenden Forschung bestand darin, den Einfluß von komplizierten Beanspruchungsschemen auf den Bruchprozess im Laufe von Belastung und/oder Entlastung von Gesteinen zu untersuchen. Der erste hier beschriebene Satz von Experimenten wurde mit einer dreiaxialen Belastungsmaschine angestellt. Diese Experimenten zusammen mit dazugehörigen numerischen Simulationen zeigten Unterschiede zwischen Be- und Entlastungsbeanspruchungen in Bezug auf mikrobruchmechanische Mechanismen (d.h. Scher- oder Zugrisse) an, aber nicht in Bezug auf den Makrobruchprozess. Der zweite Satz von Experimenten umfasste Gesteinsbeanspruchung in mehreren Zyklen von Drei-Punkt-Biegung, indem die Gesteinsproben zwischen den Zyklen um einen angegebenen Winkel (0°, 90° oder 180°) gedreht wurden. Falls die Probe um 90° oder 180° gedreht wurde, wurde kein Kaiser-Effekt im zweiten Zyklus beobachtet.

Jan 1, 2003

Mr. BRADFORD said :-On assuming this chair, which has been occupied by so many gentlemen of conspicuous ability; my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year.When considering the subject matter of this address to you to-night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion. Next I turned to a consideration of whether a discourse on the theory and practice of iron and steel would be of interest.I, however, banished this idea also from my mind, because it appeared to me that you have already had a surfeit of this on your visits of inspection to our local industries and I did not want in any way to be held responsible for the iron entering into your souls! I therefore propose, with your kind consideration, to address you on other subjects of common and vital interest to all.My first words and thoughts turn on the absolute necessity of eliminating waste in our methods. If we are to succeed in our...

Jan 1, 1926