Search Documents

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By R. M. G. Machunter

The dynamic behaviour of plant circuits and the available instrumentation determine the control strategies that are appropriate for the duty of the mineral separation plant. Although steady state modelling is appropriate to provide the main requirements of grade and throughput capability of a plant, it is the dynamic characteristics that determine the tolerance of the plant to disturbances and also its controller ability. This paper explores these issues with respect to the additional use of dynamic modelling to achieve these objectives.

Jan 1, 2007

By C Menzies

Hydraulic Monitor mining at Solid EnergyÆs Spring Creek Mine has proven to be a safe and effective method of extracting steeply dipping thick seams at production capabilities approaching one million tonnes per annum.   This paper traces the development of Hydraulic Monitor mining from its initial introduction into old workings at Strongman Mine, its refinement at Strongman 2 in shallow, thick and steep workings, through to its introduction into the deep, very thick seams at Spring Creek Mine. This last step of the progression came with all the added complications that come with depth, particularly flammable gas.   This paper will describe the various changes in mining conditions that dictated the performance of the monitor, how the mine layouts were changed to adapt, and the various operational systems that were put in place, to allow a safe and productive operation.

Jan 1, 2007

By L. Tapia

The main disturbance for stability in primary grinding using SAG mills is related to continuous changes in the ore being fed to the plant, such as size and hardness. Searching for stability is the first step to accomplish, before trying to maximize the mill throughput. The time variability in the characteristics of the ore being fed from the mine to the plant must be known or inferred to perform adaptive changes in the grinding process control. In day to day operation, such information is not available in real time. Transport times and inventories between the mine and the plant complicate the situation. Under this scenario, Minera Los Pelambres implemented a grinding optimization strategy, based on the real time analysis of certain process variables, such as ore size, mill current consumption, pebble generation and throughput. As a result, both grindability and stability indexes are inferred. This is equivalent to inferring the ore characteristics by knowing its effect on the grinding behavior. These two indexes permit control of the SAG mill total charge level and hence, allow optimization of throughput by means of an expert control system.

Jan 1, 2007

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By J McNee

Pike River Coal Limited (PRCL) is developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine is being developed to extract a coking coal deposit of the Brunner Seam, some 46 km northeast of Greymouth, using a combination of continuous miners, road-headers and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumped down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.   PRCL faces significant challenges to achieving the goal of cost effective production. The remoteness, high rainfall (greater then 6 metres per year on average), temperature variation and restrictions on access to this subalpine environment have driven the project to develop some distinctive solutions. These include the establishment of survey control in such a difficult environment with vertical and sub-vertical rock faces, significant vegetation and steep slopes by using helicopter survey, aerial photography and LIDAR (Light Detection And Ranging) aerial survey. PRCL has also commenced designing the placement of the main ventilation fans in an underground chamber in the stone drive.

Jan 1, 2007

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow inby the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

Jan 1, 2007

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By G S. C Murray

Major mining projects are developed with the assistance of lending institutions who provide hundreds of millions of dollars in funding over several years, and of course expect those funds to be returned with interest. Two Australian banks have adopted the Equator Principles, an emerging financial industry benchmark for assessing and managing environmental and social risk in project financing. Project financiers have encountered environmental and social issues that are both complex and challenging, particularly with respect to projects in the emerging markets of Asia-Pacific and elsewhere. There are many recent and historical examples of failures by resource companies to effectively manage their environmental, social, safety and security risks, some of which have caused the project to fail completely, and some of which have caused the temporary cessation of production. These events put the financial institutionsÆ funds at risk through inadequate management capacity and non-compliance adversely affecting the ability of the borrowers to repay the loans. They can also reflect adversely on the reputation of the lending institutions. In assessing these risks, lenders are increasingly looking at the track record of the borrower in its country of origin and in other countries where it operates. Lenders are wary of companies that have one standard for operations in a developed country, where the regulatory environment may tightly control what they do, and another standard for operations in countries where the regulatory regime is perhaps less stringent. Lenders may require environmental and social reviews or audits to be conducted on their behalf by competent third parties prior to a loan being approved, and annually over the life of the relationship. The mining industryÆs concept of the unwritten æsocial licence to operateÆ is highly relevant in relation to the delivery of community benefits that are sustainable post-mine closure. This paper provides examples of recent practices that support financial viability and sustainable development, as well as examples of some failures that have put lenders at risk.

Jan 1, 2007

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: ? How do mill lifters and liners really work and have an effect on grinding? ? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the `extreme' form the major observations and conclusions expressed in this paper are that: ? the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; ? the often promoted theory that balls impacting the ?toe of the charge? is a dominant form of breakage is incorrect; and ? fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

A Joy Global Inc. Company [ ] ? Joy Global Inc. headquarters located in Milwaukee, Wisconsin ? P&H Mining Equipment surface mining equipment and support ? Joy Mining Machinery underground mining equipment and support

Jan 1, 2007

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By C. F. Vos

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate (DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromiter ejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2007

This paper will address this question from the point of view of a drill and blast engineer or researcher working in open cut and underground mining operations. The paper will establish a common set of reference standards for high-speed imaging and data capture, which engineers and researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of mining and blasting applications analysis and research. In addition, the paper will examine the different technologies from an image quality and data stream reference point, ease of operation, cost, and reliability parameters. Finally, this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of quality control, research and analysis in the mining based industries. This will include a novel approach to digital high-speed imaging and data analysis in the field, which should deliver high-quality images and data analysis in a time frame that is more appropriate to the need for immediate action, analysis and problem solving.

Jan 1, 2007

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007