Search Documents

By Lawrence Neal Post

Introduction Synthetic soda ash production began to decline in the late 1930s. This was due to high operating costs and waste disposal problems. Since soda ash was used as a major component in manufacturing glass, an alternate method of producing that chemical was necessary. A process to produce soda ash from trona was developed by FMC Wyoming Corp.'s predecessor, as well as an economical way to obtain trona. Existing trona operations are located about 40 km (25 miles) west of Green River, WY. Five operators presently mine trona in this area. FMC's property has 153 km2 (59 sq miles) leased. Its eight shafts reach 488 m (1600 ft) deep to the uniform trona deposit. The seam ranges in thickness from 2.4 to 3.6 m (8 to 12 ft). History Egyptian tombs, dating from 4000 to 3000 BC, contained mummies preserved by an embalming process using soda ash. For many years, soda ash was produced by burning marine plants, then dissolving the soluble material (sodium carbonate) from the ashes. The name soda ash is derived from this method of production. In 1791, Nicola LeBlanc developed black ash, or salt cake, from salt, sulfuric acid, coal, and limestone. This process remained in use until 1863, when Ernest Solvay developed a method for producing soda ash from salt, coke, and limestone with ammonia as a catalyst. This Solvay process was widely used. And, in the 1930s, there were 17 plants in the US alone. High plant operating costs and waste disposal problems, however, necessitated finding an alternative to the Solvay process.

Jan 10, 1985

By D. King

Outline ? Regional Geology and Deposit types ? PM Deposit Exploration History and FNX?s Exploration Strategy ? Deposit Geology and Interpretation ? Resource Estimation ? Reconciliation ? Conclusions ? Breccia of comminuted footwall rocks from passage of shock wave due to meteorite impact ? Matrix ?pseudotachylite?-like? ? Variable re-crystallization of matrix due to thermal metamorphism &/or alteration

May 1, 2006

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By R. F. Lee, G. Purcell

Tests carried out in the Department of Mining and Metallurgy at the New Mexico Institute of Mining and Technology indicate that high density rigid foams may, with the addition of suitable fillers, have structural properties comparable with concrete. Since polyurethanes have other useful properties that are unique to the foams, they have great potential value for both mining and civil engineering applications. Polyurethane, a generic term for a wide variety of closely related foam compounds, suggests rather misleadingly that foams are simple polymers of the urethane monomer ethyl carbamate (H,NCOOC,H,) . Polyurethane foams certainly do contain urethane groups, but these need not necessarily preponderate. Other reactive groups may be, and usually are, present so that the final polyurethane product will most likely contain, in addition to urethane groups, aliphatic and aromatic hydrocarbon, ester, ether, amide and urea groups.

Jan 9, 1963

By Joseph J. Feiler

Fires in underground coal mines are persistent problems anywhere in the world that coal is mined. Coal fires pose safety and health hazards in the form of mine subsidence, loss of energy reserves, destruction of property and surface improvements, and air pollution. In 1995, the US Bureau of Mines (US-BM), in cooperation with the Colorado Division of Minerals and Geology (CDMG),entered into a contract with Goodson & Associates Inc. (GAI) to design and field test the effectiveness of a new foamed grout technology called ThermoCell. GAI is a Lakewood, CO geotechnical and mining reclamation engineering firm. The company developed ThermoCell to control and extinguish underground coal fires. The viability of the special grout and the technology of application were established during a full-scale field demonstration at the abandoned IHI Coal Mine fire, near Rifle, CO. Following acquisition of additional funding by CDMG in 1999, Goodson returned to the site in April to continue the grouting to fully extinguish the IHI fire.

Jan 1, 2000

By S. Pal, A. K. Lahiri

Most of the compounds present in slag are surface active. This gives rise to foaminess of slag. The foam life and foaming index are normally determined by the draining rate of slag through the plateau border, so the foaming index is directly proportional to slag viscosity and inversely proportional to slag density and bubble diameter. When a small amount of a strong surface active compound like P2O5or Cr2O3is present in slag, however, the foam life increases significantly and the above relationship is not obeyed. The strong surface active compounds reduce the draining rate from the film between the adjacent bubbles so the film draining controls the life of the foam. The thickness of the film, Marangoni force, viscosity of the slag, and diffusion of surface active compounds determine the film draining rate. The interplay of these factors leads to very low or high film draining rates and affects the film and foam stability significantly. Keywords: slag, foam, foaming index, film draining

Jan 1, 2004

By M. Görnerup, A. Kapilashrami, Seetharaman. S., A. K. Lahiri

Simultaneous reduction and foaming of chromium-rich slag have been studied in a laboratory furnace equipped with X-ray image analysis. Reduction of the metal oxides by graphite generated CO, which caused the melt to foam. The slag composition continuously changed due to reactions and dissolution of lining. Gas generation rate, foam height, and gas bubble size were studied and correlated to slag composition. Viscosity increased significantly during the experiments due to a change in slag composition. Bubble sizes varied little during the progress of reactions but differed considerably for different slags. Bubble sizes were largest for V2O5 containing slag, which is contrary to the general understanding that the presence of strong surface active agents reduces the bubble size. The foaming index did not follow expected trends for bubble size and viscosity, suggesting that foaming index is not a suitable parameter for discussion of foams under dynamic conditions. Keywords: slag, foaming, dynamic conditions

Jan 1, 2004

By M. B. C. Brandt

Focal depths of 15 tectonic earthquakes and 9 mine-related events were determined for South Africa using data recorded by the South African National Seismograph Network. These earthquakes and events were relocated by means of the Hypocenter program using direct P-waves (Pg) , critically refracted P-waves (Pn) , and first-arrival S-waves for the magnitude range 3.6 ?? ML ?? 4.4. Focal depths were first determined by means of the minimum root mean square (RMS) of the differences between the measured travel times and those predicted using the velocity model. The depths for tectonic earthquakes had a 2 km ?? D ?? 10 km range and an average depth and standard deviation of 6.9 ± 2.3 km. Depths for minerelated events ranged over 0 km ?? D ?? 7 km, averaging 3 ± 2.3 km. Next, arrival times for the additional regional depth phases sPn , PmP, sPmP, and SmP were measured. Focal depths were re-determined for the relocated epicentres, with the minimum variance (i.e. spread) of the differences between the measured travel times and travel times predicted by means of the Wentzel, Kramer, Brillouin, and Jeffreys (WKBJ) method for synthetic waveform modelling. Depth ranges were 4 km ?? D ?? 7 km (average 5.9 ± 1.2 km) and 1 km ?? D ?? 4 km (average 2.4 ± 1.2 km) for tectonic and mine-related events, respectively. The derived depths were verified for one tectonic earthquake with synthetic-to-recorded-waveform fits using the WKBJ synthetic seismogram software for the abovementioned regional phases. The focal mechanism parameters for this earthquake source were obtained from the National Earthquake Information Centre. Focal depths were estimated for nine stations by visually comparing synthetic waveform phases with recorded waveforms, ranging from 5 km to 8 km.

Jan 1, 2014

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By Launa Mallett, Michael J. Brnich

The first step to emergency preparedness is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen all at once. Risk assessments are used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. While the examples provided in this training package are specific to mine fires, the concepts and tools can be applied to any mine hazard. Purpose: This training package was developed to assist instructors, as they: 1) determine how to use risk assessment to improve preparedness for mine fire emergencies and 2) present risk assessment concepts and tools to trainees. Audience: This package is appropriate for workers/trainees from all types of mines. A risk analysis can be conducted by anyone familiar with the location(s) being studied. Why Conduct a Fire Risk Assessment? During a risk assessment, hazards are evaluated in terms of the likelihood that a problem may occur and the damage it might cause. Mine fire preparedness requires consideration of all possible fires that could occur. However, at a given mine some fires are more likely than others and some would result in greater damage than would others. Conducting a risk analysis identifies these differences. The results can be used to target resources at the types of fires that are most likely and/or are most destructive. Hazards that are very likely to result in fires that would do considerable damage to people and property should be targeted first for remediation and/or effective response if remediation isn't possible. Potential fires that are less likely or that would have less severe consequences are identified for attention later, after the more serious situations have been addressed.

Jan 10, 1992

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

By James L. Christensen, Gregory Sanchez, Michael P. Walker

The Fogg Museum expansion project required excavation and construction in a congested urban area in Cambridge, Massachusetts. A soldier pile tremie concrete (SPTC) wall provided the support of excavation and now serves as the permanent basement wall of the new expansion of the museum. The existing Fogg museum had a single basement level. The new expansion has a two-level basement for new exhibit space and an amphitheater. The east side of the site is about 20 feet above the basement level of the existing Fogg structure which resulted in a significant unbalanced load that needed to be resolved without damaging the original Fogg structure. The SPTC wall was supported with a combination of tiebacks and internal bracing. The final depth of the excavation was about 40 feet below street level. Strict movement control was imposed because the existing museum contained an Italian Renaissance-style courtyard. The southeast corner of the SPTC wall had to accommodate underpinning of an historic concrete ramp which was ultimately incorporated into the expansion. Challenges during construction included excavating the SPTC wall panels up to 12 feet into argillite bedrock which had occasional diabase dikes and sills. The following topics are discussed in more detail after a general project.

Jan 1, 2015

Wrenching between basement blocks is considered to be the mechanism whereby a well developed set of en echelon folds and an associated fracture system are developed in the Fitzroy Depression, Western Australia. The regular geometry of these structures accords with a right lateral regional coupling between high-standing, basement blocks bounding a trough filled with a thick pile of stratified Phanerozoic sediments. The structures developed during or after the Mesozoic Era, but the couple is inferred to have been applied to blocks outlined by old lineaments, which may reflect strains or ruptures in basement that developed during the Precambrian, and which were regenerated during Palaeozoic and Mesozoic time.

Jan 1, 1967

By J. B. Gilliatt

The discovery of ore at Wabana was quickly followed by the mining of the ore beds where they outcropped in the land areas. The third phase, as at present carried out, consists of extensive submarine operations, which were commenced in 1908, by driving a pair of slopes out under Conception bay, opening. the mine for a distance of a mile and a half from the shore. Two other slopes, now driven just beyond the shore line, are being sunk to the submarine territory where, it is generally recognized, huge reserves of ore lie under the bay. The process of erosion of the land, the solution and re-disposition of its iron-bearing minerals in thick beds of ore have been considered elsewhere, but these bear small relation to the physical forces which have acted upon the ore-beds since the deposition of the strata. These physical changes are made manifest by jointing and cleavage and faulting. The discussion of these, the relation they bear to each other, and to the folding of the strata, is the purpose of this article. For the benefit of those who may not be familiar with the formation in which the ore occurs, I include a general summary of the geology of Be!! island and its environs; also a description of conditions that prevailed during the period of deposition, so that the reader may appreciate some of the later changes that took place during or subsequent to its emergence from the sea, and the folding or tilting of the strata to the position it now occupies.

Jan 1, 1924

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

At a regional scale, the Otago Schist has been divided into textural zones, metamorphic zones, structural transposition zones, and terranes and lithologic associations. Each of these subdivisions reveals aspects of the internal structure of the lithologically monotonous Otago Schist but, to date, a map of the schist derived directly from structural data has not been made. In the present study, digitised structural data from the QMAP GIS were used to make a form line map of Schist foliation which, in turn (and using certain non-unique guiding assumptions), was used to construct a provisional foliation thickness map of the Otago Schist. Contours of dominant foliation (Sp) thickness have been drawn from 4 kIn above to 16 km below the reference level of the Caples-Torlesse terrane boundary in the schist structural pile. A recent revision of the Otago Schist textural zone classification has shown that the grain size of metamorphic white micas increases progressively with textural grade. There also appears to be a correlation between schist mica grain size and foliation thickness. Using mica grain size, it may eventually be feasible to establish the vertical structural position of samples in greenschist facies parts of the schist pile to a precision of ¦ 1 km or better, even if they are in inliers or fault-bounded blocks. Foliation thickness and mica grain size are thus potentially useful tools for research and exploration in the Otago Schist in that they assist with structural interpolation and extrapolation. Even at this early stage of application they can be used to provide hitherto unobtainable, semi-quantitative estimates of displacement on Mesozoic and Cenozoic faults and folds.  

Jan 1, 2001

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979