Search Documents

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933

By HeeDong Lee, Owen Reedy, Lawrence Matson, Naidu Seetala, Thomas Key

Spark Plasma Sintering (SPS) consolidated ZrB2+SiC composites using nano-powders (around 40 nm) showed smaller grains compared to those using micron size powders and segregation of SiC into islands is minimal but with higher oxidation of ZrB2 to form ZrO2 in nano-composites. Argon-gas purging prior to SPS consolidation at around 2000 °C and 40 MPa of ZrB2+20vol.%SiC nano-powders was used to minimize the oxidation and obtain fine granules with high densification. The densification of the Argon-gas purged nano-composites is higher compared to those consolidated without Argon gas purging. The EDX analysis showed a strong reduction in the oxygen peak for the Argon gas purged composites. The XRD spectra also support this observation with less ZrO2 phase composition in Argon gas purged composites. The Vickers micro-hardness showed slightly lower values for Argon gas purged composites though they have higher densification.

Mar 1, 2017

By V. Baltazar

The behaviour of arsenic and antimony during copper electrorefining was studied in order to identify the conditions under which good quality copper cathodes could be produced from anodes with high levels of these impurities. Examination of the effect of current density over the range 21 to 37 mA/cm2 indicated that the relative amounts of As and Sb entering the electrolyte affected the onset of passivation. When the ratio of As/Sb entering the electrolyte was greater than 2, the anodes showed no sign of passivation even at the highest current density; when the ratio was less than 2, the anodes passivated at 37 mA/cm2. Cathode analyses showed that anodes with an As/Sb dissolution ratio less than 2.0 tend to produce cathodes of inferior quality even at normal current densities (25.7 mA/cm2). The criterion of a minimum As/Sb dissolution ratio of 2.0, and mathematical correlations for the distribution of As and Sb between the electrolyte and slime developed in a previous study, allow the calculation of the maximum allowable Sb level in en anode for a given As concentration. Analyses of plant data at the CCR Division of Noranda Inc. for the last four years of operation have demonstrated that the use of this as a quality control tool has allowed the quality of copper cathodes to be maintained despite a significant increase in the average Sb levels in anode receipts.

Jan 1, 1987

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt.

Feb 1, 2020

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By Garg. D.

Premixed bronze powders are widely used to produce a wide variety of P/M components including bearings and bushings by the powder metal industry. The physical and mechanical properties of sintered bronze components such as dimensions, strength, microstructural characteristics, and sintered density are well known to change with sinlering furnace design, particle size distribution in powders, green density, preheating and sinlering time" and temperature, and protective atmosphere flow rate. " However, not much is known about the effect of protective atmosphere composition on physical and mechanical properties of sintered bronze components; This paper describes effects of protective atmosphere composition and sintering temperature on physical and mechanical properties of sintered bronze components

Jan 1, 1996

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By R. A. Cummings, N. N. Moebs, M. M. Singh

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, but may be at least partially controlled by tempering the air before it is brought to the working places. Disintegration of shale roof is progressive loosening of chunks or slabs or roof shale, which fall to the floor. Bolts are left dangling or are connected to the roof by a column of loose rock. Posts are rendered ineffective. Passage of ventilation air and personnel is restricted by piles of fallen material on the floor. Shale disintegration as it occurs in mine roofs does not appear to have much in common with slaking, such as is measured in slake-durability tests, which results in the failure of certain shales when exposed in embankments or foundations. A two-year program was conducted on behalf of the US Bureau of Mines, incorporating field and laboratory analysis of deterioration. During this study, a. survey was conducted of underground mining operations in the Illinois Basin and Appalachia. In all, 47 mines in six different coal seams were identified as possibly having roof deterioration problems pertinent to the study. Of these, the No. 1 Mine of the Valley Camp Coal Co. near Triadelphia, WV was selected for detailed study. This mine uses conditioning entries, workings where raw intake air is routed before reaching the key haulageways. Deterioration is to be confined to the conditioning chambers. The approach adopted to study the deterioration problem was to measure atmospheric moisture in the mine, determine shale behavior in the laboratory under various moisture conditions, and measure mine roof behavior that could be correlated with atmospheric moisture observations. The following tasks were performed: • Atmospheric baseline data were collected, consisting of airflow measurements, continuous monitoring of the mine and surface atmospheric conditions using a sling psychrometer. • Roof deterioration was documented through measurement of roof convergence (sag), mapping of roof conditions, collection of fallen and rashed material and measurement of roof height increase and photographic logging. An infrared scanner was also tried, but not found useful. • The behavior of shale under various moisture conditions was determined in the lab through tests of shale expansion, natural moisture content, moisture uptake capacity at various humidities, and static (immersion) slaking.

Jan 1, 1984

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By K. J. Reid, H. A. Lex, I. Iwasaki, K. A. Smith

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides from Duluth gabbro were investigated. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously ground pulps. With the ball-mill ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1984

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 5, 1950

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By Y. A. Attia, M. Elzeky

The effects of bacterial adaptation and partial replacement of leaching solution on the rate and extent of bioleaching reactions of a complex sulfidic gold ore were investigated. The ore was first concentrated by bulk sulfide, flotation, and the sulfide concentrate was treated by bioleaching using Thiobacillus ferrooxidans. The residues from bioleaching were treated by cyanidation to extract the gold and silver. Bacterial adaptation before bioleaching significantly increased the rate and extent of bioleaching reactions. Similarly, the daily partial replacement of leaching liquor enhanced to a great extent the leaching rate, and in some cases, increases of up to ten fold were observed. Both bacterial adaptation and solution replacement increased the gold recovery by about 2-fold and that of silver by about 1.3-fold. In this work, more than 95% of the gold and more than 98% of the silver could be recovered from the sulfidic gold ore when bioleaching was used ahead of cyanidation, compared with 18.3% and 52.3% by direct cyanidation.

Jan 1, 1992

By M. Elzeky, A. Attia

The effects of bacterial adaptation and partial replacement of leaching solution on the rate and extent of bioleaching reactions of a complex sulfidic gold ore were investigated. The ore was first concentrated by bulk sulfide flotation and the sulfide concentrate was treated by bioleaching using T. Ferrooxidans bacteria. The residues from bioleaching were treated by cyanidation to extract the gold and silver. Bacterial adaptation before bioleaching significantly increased the rate and extent of bioleaching reactions. Similarly, the daily partial replacement of leaching liquor enhanced to a great extent the leaching rate and in some cases up to ten fold increase was observed. Both bacterial adaptation and solution replacement increased the gold recovery by about 2-fold and that of silver by about 1.3-fold. In this work more than 95% of the gold and more than 98% of the silver could be recovered from the sulfidic gold ore, when bioleaching was used ahead of cyanidation compared with 18.3% and 52.3% by direct cyanidation.

Jan 1, 1989